Denon AVP-A1HDCI Owner's Manual page 102

4
3,4
3, 4
4
41,76,81
• Turn off the power and contact a
DENON service center.
• Replace with new batteries.
• Operate within the specified
range.
• Remove the obstacle.
.Insert the batteries in the
proper direction, following the
polarity marks in the battery
compartment
• Move the set to a place in which
the remote control sensor will
not be exposed to strong light
• Set the same remote IDs for the
main unit and remote control
unit.
• Set is damaged.
• Batteries are worn.
• You are operating outside of the
specified range.
• Obstacle between main unit and
remote control unit.
• The batteries are not inserted in
the proper direction, as indicated
by the polarity marks in the
battery compartment
• The set's remote control sensor
is exposed to strong light (direct
sunlight, inverter type fluorescent
bulb light, etc.).
• The remote ID of the main unit
and remote control unit do not
match.
Power turns off
suddenly and
power indicator
flashes red.
Set does not work
properly when
remote control
unit operated.
(Remote Control Unit)
Troubleshooting
If
a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner's manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist.
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
(General)
iN?> c'J;\::~"':lj;"0'
Ca:n. .". ' . . . · . . .
·/~i;.;<, H.Xj(·f~"
/i
;f;~"
Power does not • Connection of the power cord is • Check that the power plug is
23
turn on, or turns faulty.
securely inserted into the AVP-
off directly after it
A1HDCl's AC inlet and the wall
was turned on. power outlet
No sound is • The connection with the input • Check the connections. 11
produced from devices or power amp is faulty.
speakers.
• Device you want to play and set • Select an appropriate input 43
input source do not match. source.
• Master volume is turned too • Adjust the master volume to an 56
low. appropriate level.
• Mute mode is set • Cancel the mute mode. 56
• Headphones are connected.
• Disconnect the headphones. 56
·No digital signals are being • Select an input source for which
43,46,47
input. the digital input setting has been
made.
·The connectors to which the • Set the input mode.
45
digital inputs are assigned and
the settable input modes do not
match.
Display is off.
• The "Dimmer" setting is set to ·Set to something other than 42
"OFF': "OFF':
• The PURE DIRECT mode is set
• Set a surround mode other than 50
the PURE DIRECT mode.
"DOLBY DIGITAL:' • DVD player's digital audio output • Check the DVD player's audio -
indicator does not setting is not proper.
output setting. For details, read
appear on display.
the DVD player's operating
instructions.
I
99
4
3,4
3, 4
4
41,76,81
• Turn off the power and contact a
DENON service center.
• Replace with new batteries.
• Operate within the specified
range.
• Remove the obstacle.
.Insert the batteries in the
proper direction, following the
polarity marks in the battery
compartment
• Move the set to a place in which
the remote control sensor will
not be exposed to strong light
• Set the same remote IDs for the
main unit and remote control
unit.
• Set is damaged.
• Batteries are worn.
• You are operating outside of the
specified range.
• Obstacle between main unit and
remote control unit.
• The batteries are not inserted in
the proper direction, as indicated
by the polarity marks in the
battery compartment
• The set's remote control sensor
is exposed to strong light (direct
sunlight, inverter type fluorescent
bulb light, etc.).
• The remote ID of the main unit
and remote control unit do not
match.
Power turns off
suddenly and
power indicator
flashes red.
Set does not work
properly when
remote control
unit operated.
(Remote Control Unit)
Troubleshooting
If
a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner's manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist.
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
(General)
iN?> c'J;\::~"':lj;"0'
Ca:n. .". ' . . . · . . .
·/~i;.;<, H.Xj(·f~"
/i
;f;~"
Power does not • Connection of the power cord is • Check that the power plug is
23
turn on, or turns faulty.
securely inserted into the AVP-
off directly after it
A1HDCl's AC inlet and the wall
was turned on. power outlet
No sound is • The connection with the input • Check the connections. 11
produced from devices or power amp is faulty.
speakers.
• Device you want to play and set • Select an appropriate input 43
input source do not match. source.
• Master volume is turned too • Adjust the master volume to an 56
low. appropriate level.
• Mute mode is set • Cancel the mute mode. 56
• Headphones are connected.
• Disconnect the headphones. 56
·No digital signals are being • Select an input source for which
43,46,47
input. the digital input setting has been
made.
·The connectors to which the • Set the input mode.
45
digital inputs are assigned and
the settable input modes do not
match.
Display is off.
• The "Dimmer" setting is set to ·Set to something other than 42
"OFF': "OFF':
• The PURE DIRECT mode is set
• Set a surround mode other than 50
the PURE DIRECT mode.
"DOLBY DIGITAL:' • DVD player's digital audio output • Check the DVD player's audio -
indicator does not setting is not proper.
output setting. For details, read
appear on display.
the DVD player's operating
instructions.
I
99