Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. LG Electronics hereby declares that this/these This equipment generates, uses, and can radiate radio frequency product(s) is/are in compliance with the essential...
Safety Information IMPORTANT SAFETY Disposal of your old appliance INSTRUCTIONS 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal 1.
‘damaged’ while playing a recording stored inside the system’s HDD, it must be replaced with a new one. Ask for an engineer’s assistance for HDD replacement from your dealer. LG Electronics is not responsible for deleted data caused by user mishandling. •...
In order to maintain stable system performance, have your system checked regularly by the service center. LG Electronics is not held responsible for system breakdown caused by user mishandling. There is a risk of explosion if a battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Contents Contents Screen on the Main Monitor Main Monitor Screen Moving the Channel's Position Selecting the Main Monitor screen mode Selecting the Spot Monitor screen mode Grouping channel PTZ Camera Control Using the Digital Zoom function Export the recorded data Safety Information Viewing the System Log List Viewing System Information...
LG Network Client Program Introduction Recommended PC Requirements Before install the program Getting Started Install the LG Network Client on your PC Starting the LG Network Client LG Network Client Overview Operation and settings Register the Site Name or Group Name...
Text Input for ATM and POS device. • Full real-time recording. • User management (User level control). Up to 480 IPS @ 704x480, LRH7160D Series • PTZ Control. NTSC Up to 240 IPS @ 704x480, LRH7080D Series Dome camera telemetry control (Dome OSD control).
Preparation Front Panel Front of the LRH7160D series FOCUS+ IRIS+ INFO ALM.OFF FOCUS - IRIS - ALARM TEXT OFF CLEAR SHIFT 10/0 BACK UP COPY MARK MOVE TOUR FOCUS+ IRIS+ INFO ALM.OFF FOCUS - IRIS - SEARCH SETUP ALARM TEXT OFF...
Preparation Channel Buttons: You can input a number with channel buttons. You can also use the channel buttons for sub-function with SHIFT button (11 to 16 buttons of 8 channel DVR are used for sub-function without SHIFT button.). • The LED in the button indicates the status as follows: Off: The current status is for live mode.
Preparation Rear Panel Rear of the LRH7160D series Rear of the LRH7080D series VIDEO INPUT: Connect the camera’s video output to these BNC connectors. LOOP OUT: The signal from VIDEO INPUT connector is looped out to this connector. RELAY-OUT Terminals: Output terminals for alarm (relay) signal.
Preparation Remote Control Button Description POWER (1) Turns DVR on or off. LOGIN Displays the User Log-In dialog box or logs out. Set the appropriate DVR system ID to operate via the IR Remote Controller when using the multiple DVR. Press the ID button then press the number button within 2 seconds to select the system ID of the DVR.
Installation Installation Connections Precautions • Depending on the camera and other equipment there are various ways to connect the unit. Please refer to the camera manual or manuals for other devices as necessary for additional connection information. • Be sure to switch off the camera before installation and connection. Basic Connection Overview Connect the coaxial-type cameras Connect the Monitor, DVR, VCR, or others.
Installation Connecting Camera Connecting Display device Connect the video output of your camera to the unit, using a This unit can be output simultaneously from the HDMI, VGA and standard 75 Ω video coaxial cable with BNC connector. SPOT OUT jack. The video signal connection between the DVR and LOOF OUT connector passes the video signal from VIDEO INPUT the monitor.
Installation HDMI Monitor connection Connect the unit to the HDMI monitor using a HDMI cable (Type A, High Speed HDMI Cable). HDMI Monitor connection MAIN SPOT USB Memory device Insert the memory device into the USB port. The system automatically recognizes the device. The system software can be easily upgraded using a USB memory device.
Installation Connecting ATM/POS Connecting Network Connect the ATM/POS unit to the ATM/POS port. You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or monitor the image via network. After the ATM/POS device connection installation, check the network settings for the remote control and monitoring work.
Installation Connecting RS-485 device Connecting LKD1000 controller Connect the LKD1000 controller to control the DVR. (Refer to the This DVR has two data terminals. Use this port to connect PTZ manuals of the LKD1000 controller for more details.) The LKD1000 cameras, DVRs or keypads (optional).
Installation Alarm Output Sensor input connection Connect the alarm device to the alarm output. Alarm signal outputs when an event occur. Alarm output connection Alarm device Alarm device Terminal No. Description Alarm sensor Alarm sensor Ground Alarm Output 1 Alarm Output 2 Terminal No.
Installation HDD INSTALLATION 6. When you turn the power of the unit on, the new HDD is detected and formatted automatically. CAUTION Note for Hard Disk Drive You should install the hard disk drive from 1 to 6 in order. The internal hard disk drive (HDD) is a fragile piece of equipment.
Installation System Operation General Explanation of the Live Screen on the Main Monitor 1. Turn on the unit. System booting will commence. The LG logo image will be displayed on the main monitor during the system Main Monitor Screen booting.
Installation Moving the Channel's Position You can control the PTZ Camera. (optional) You can change the camera channel's position in a split screen of the Main Monitor. g Live Screen 1. Select a desired channel by clicking the left button of the Displays the current surveillance live screen.
Installation Selecting the Spot Monitor screen mode Grouping channel You can select the live screen mode to full, 4-split, 9-split or 16-split You can group channels you want. screens on the spot monitor. 1. Press CAM or click the icon in the system control bar. 1.
Installation Preset Settings You can adjust the focus of a camera Preset position is the function to register camera monitoring manually. positions (preset positions) associated with position numbers. You can adjust the iris of a camera By entering the position numbers, you can move cameras to the manually.
Installation Viewing the System Log List NOTE To view the system log list: • Check the export device before you proceed. 1. Press the LOG button or click the icon in the system control • You can also use the COPY button on the front panel for bar.
Installation Configuration menu Viewing System Information To view system information: 1. Press the INFO button or click the icon in the system control bar. The system information window is displayed on the main The features and options of the DVR are configured through the monitor.
Installation System settings Setting the Menu Using the Front Panel Buttons or Remote Control Buttons Remote Front Panel Description Control Properties Use these buttons to select the menu options or adjust the options value. SEARCH SETUP Select the option or confirm the LOG-IN VIEW BACK...
IP address. • Host Name: Enter the host name you want to use. You can not use the “www”, “mail”, “http”, “ftp”, “com”, “lg”, “lge”, “lgddns”, “lgeddns”, “ddns” for host name. • Interface: Select a LAN port you want to use (Ethernet 0 or •...
Installation Date/Time please check network connection. When you want to change DDNS host name If you want to change the registered host name to new one, follow as shown below. 1. Enter a new host name in the [Host Name] option. 2.
Installation Controller 7. Click [OK] to restart the DVR. NOTE • Do not turn the power off during the update process to prevent the malfunction. • Do not remove the external device or CD/DVD disc for update while the update is in progress. It may cause a malfunction. Backup •...
Installation Daily/Weekly backup NOTE 1. Connect the USB device for backup. You cannot use the CD or DVD writer for daily or weekly backup. • The backup function is not supported on the external USB CD-ROM driver. 2. Select WEEKLY or DAILY on the schedule options. •...
Installation Device settings Settings for the PTZ cameras connected via the data port of the RS-485 terminal. Camera • Channel: Selects the desired channel to set the connected PTZ camera. • Ch: Displays the channel number. • Port: Selects the connected data port of the RS-485 terminal •...
Installation IP Device on the drop-down list. Relay Type: Select the relay type. Control Duration: Enter the relay time. Motion Setting You can configure this option when you select to [LGE] on the [Driver] option. Select [Motion] tab of the [Setup] window. 1.
Installation To register the IP device automatically NOTE • The Supported IP camera specifications. Specification Description Driver LGE, AXIS, ONVIF Recording mode Continuous, Instant, Motion, Sensor Video Codec H.264, MPEG4, MJPEG Audio recording and Support playback Resolution CIF, Half D1(2CIF), D1(4CIF), UXGA, 720p, 1080p (Up to 2048 x 1536) 1.
Installation Display settings Storage • Overwrite: Sets whether you use Overwrighting function. • Full Warning: When the HDD has overflowed a warning message is displayed. • Auto Delete: Sets the auto delete date. If you set the auto delete • Channel Name: Mark up to display or remove the channel name date, the recorded data will be deleted except the data within in the channel window.
Installation Record settings Video Adjustment Adjust the brightness, contrast and color settings of each camera channel. You can see the settings screen from the preview windows. Normal Schedule Recording A Normal schedule recoding can be activated at preset times, in a repeating pattern on selected weekdays.
Installation 3. Drag and drop with left button of the mouse to set the channel 2. Select a recording mode. and time you want to record. The color of the time block is changed depending on the selected mode. • Gray (No recording): No schedule recording.
Installation Normal Settings concerning normal recording. 2. Enter the name of the special day. Use w/s/a/d to select the [Name] column and press OK. The virtual keyboard menu appears. • CH: Displays the channel number. 3. Use w/s/a/d to enter the necessary information for year, •...
Installation Event settings Motion Sensor • Channel: Select the channel to set motion detection. • Sensitivity: Set the level of sensitivity for the created motion detection area. Sensitivity can be set from level 1 to 10 or OFF. • Relay Output: Select the number of the RELAY-OUT terminal for •...
Installation ATM/POS Data Format Event Popup The DVR can be set to react to text input from devices such as ATMs (Automated Teller Machines) and POS (Point of Sale; i.e., cash registers). This screen allows you to configure the DVR for your input device.
Installation Mail Emergency • Notification: Mark up to be notified the unit's operating • Notification: Mark up to be notified the emergency agent about information according to notification settings by e-mail. the unit's operating information according to your notification settings. •...
Installation Buzzer • Trap Community String: Specifies the SNMP trap community in which you want to enable this system (e.g. lgecommunity or Marks up when you want to activate the selected option. public). Output • Sensor: Makes a sound when a sensor occurs. •...
Setup, Search/Play, Export, PTZ, Power Off, Instant Record: Set the authority for the selected group. Mark up the option to activate it. • Main Channel/Spot Channel: Selects the channel to allow the operation for the group user. The LG logo is displayed on the covert channel(s).
Installation Setup Wizard settings Step 2 Set date and time. The Setup Wizard appears on the screen when you turn on the unit for the first time or select [Setup Wizard] on the Setup menu. You can set the System name, display language, data, time, network settings, recording schedule and recording mode on the initial setup wizard.
Installation Step 3 Step 5 Set network address for LAN ports. Set recording mode for the Continuous and Event recording. • Interface: Select a LAN port you want to use (Ethernet 0 or • Resolution: Selects the recording resolution. Ethernet 1). •...
Operation Operation Instant Recording NOTE • External recording devices can be used as copy areas for images recorded on the hard disk. It is impossible to record Images from a camera will be recorded on the built-in hard disk. images on the external recording devices directly. Ensure all the cameras are connected and that time and date have •...
Operation Instant Playback 7. Press ad (Play) button or click button to start playback. The picture(s) is (are) displayed on the main monitor. 8. Press STOP (Z) to stop playback and return to the search menu. 9. Press BACK repeatedly to exit the [Date/Time] menu. It is possible to play a recorded image without stopping recording.
Operation ATM/POS Search 5. Use w/s/a/d button to select the channel and press OK button to confirm the selection. If you want to select the all Search the recorded text information by ATM/POS device. channels, marks up the [Select All] option. This function is available with backup data of the internal or external 6.
Operation Export Search Smart Search Searches an exported data in the external device or internal You can be searched the recorded data by specifying the motion DVD-ROM device. detection conditions. If you want to use this function, you have to connect the external device or insert the CD/DVD disc with exported data otherwise the warning message will be displayed.
Operation Functions Available During Playback Button Function FOCUS+ IRIS+ Playback Remote Control Front panel Control Menu INFO ALM.OFF FOCUS - IRIS - Stops playback. ALARM TEXT OFF CLEAR SHIFT 10/0 INFO ALM.OFF BACK UP COPY MARK MOVE TOUR Pauses playback. ALARM TEXT OFF FOCUS+...
Operation Using the playback control menu Using the Protect function You can use various playback function using playback control menu. This function allows you to protect the recorded data against being automatically overwritten. 1. Play a data recorded. Playback control menu appears at the bottom of the screen. How to select Protect section.
2. Enter the password. (Note that the default client password are Memory 2 GB or above RAM “000000”.) 3. Click the [OK] button and then the LG Network Client window is Graphics Card 128 MB or above Video RAM (Use latest displayed.
LG Network Client Program LG Network Client Overview File End Backup Use to stop and exit the backup Search search function. Selected Menu Tab Software Update Use to upgrade DVR/NVR software or Live window add/upgrade PTZ protocols. Tool Bar Menu Bar 1.
When you click the PAUSE button to Information windows. You can add, edit or delete pause the playing the recorded data the site name or group name in LG of the selected channel, the Print Icon Network Client. is activated. You can print the paused...
Register the Site Name or Group Name 6. Enter the TCP/IP port number of the DVR/NVR. If it isn’t entered, The first time LG Network Client is started, you should register a site the port number is set by default.
Disconnect: Select to disconnect to the site name. 3. Repeat step 1 to 2 to connect the other site name. NOTE Up to 5 users can connect to the DVR/NVR system using the LG Network Client program. Connect the group device 1.
LG Network Client Program Instant playback NOTE It is possible to play a recorded image without stopping recording. 1. Select the [Camera View] tab in the live mode. • To delete the camera from Live Window, Click desired channel number on the [Cameras] and then drag drop where not Live 2.
LG Network Client Program Pan/Tilt/Zoom Tab To Register Preset Positions You can control the PTZ cameras via the network. 1. Move the camera to a point you wish. 1. Select the PTZ camera channel window in the camera view 2. Click the [SET] icon.
LG Network Client Program Log View Tab Edit the favorite 1. Select the registered favorite name and click the right mouse You can see the system log list of selected site name. button. 1. Select the [Log View] tab. 2. Select the [Edit Favorite] option. The Edit Favorite window is 2.
LG Network Client Program Event Search Tab Smart Search Tab Searches a recorded picture by date and event type. Searches the recorded data by specifying the motion detection conditions. 1. Select the [Event Search] tab. 1. Select the [Smart Search] tab.
LG Network Client Program Using the Remote Setup function ATM/POS Search Tab Searches the recorded text information by ATM/POS device. You can set the DVR/NVR configuration of a selected site name This function is available with backup data of the internal or external using this function.
LG Network Client Program Device settings obtain the average time among 5 public servers (time.nist.gov, time-a.nist.gov, time-b.nist.gov, ntp.nasa.gov, clock.isc.org). • Private Time Server: Enter the private time server’s IP address or host name. • Sync. Interval: You can set synchronized intervals with the NTP time server to 1 day, 1 hour, 1 month and 1 week.
LG Network Client Program Display settings again. • XX: Connection failed. 3. Click the [CLOSE] button to exit the window. ATM/POS Setting • Interface Device: Select the interface device from the drop- down list. • Camera: Select the camera number for mapping with ATM/POS device.
LG Network Client Program Motion Settings Record settings • Sensitivity: Set the sensitivity level for the created motion detection area. • Relay Output: Select the number of the RELAY-OUT terminal for the output alarm (relay) signal when motion is detected.
LG Network Client Program Event Settings 3. Select the desired channel to schedule recording. 4. Click the start time cell block and drag & drop to select a time period cell block. Click the start time cell block of a channel and drag & drop across the channels to select the time period block for multi- channel setting at the same time.
LG Network Client Program Notification NOTE Mark up when you want to activate the selected option. If the selected notification option is activate, notify the user about the • ATM/POS Recording Information. information of selected option by E-mail. • Sensor On: Sends an e-mail when a sensor has occurred.
Record: Set the authority for the selected group. Mark up the option to activate it. • Main Channel/Spot Channel: Selects the channel to allow the operation for the group user. The LG logo is displayed on the covert channel(s). User 1. Select the [User ID] from the drop-down list.
LG Network Client Program Using the E-Map function Add the Map 1. Click the [Add E-Map] button. The Add E-Map window is This function gives a visual overview of the cameras in your displayed. surveillance environment. 2. Click the [...] button in the [E-Map path] option.
LG Network Client Program Using the Multiple Window function Using the Protect function This function allows you to see a live screen maximum 64 channel This function allows you to protect the recorded data against being by using two monitor.
LG Network Client Program Additional Programs To activate the Emergency Agent program 1. Run the [LG Emergency Agent] program. The Emergency icon is displayed in the system tray. 2. Whenever a notification function occurs, a message box is displayed on the bottom right of the screen.
Camera Number: Displays the camera channel number of recorded data. Video Information window. To play the exported data 1. Run the LG Export Viewer program on the PC or in the Export Playback control buttons. Viewer folder of the external USB device. Option setting window.
• The exported data of [AVI LG] file format is always displayed OSD. To playing AVI LG file, you have to install the LG DVR Codec. • If you select AVI file format, it can play on any media player. But OSD may not be displayed on some media player.
LG Network Client Program Event Search 1. Select the [Event Search] tab. 2. Click the icon and select starting and ending date. (The selectable date is displayed in blue color.) 3. Enter starting and ending time. 4. Select the camera channel for event search.
Check the power cable on the camera is connected correctly. displayed on the screen but the camera images are not Check there is no problem with the video cable connection between the camera and the LG DVR displayed. system. Turn off the DVR system and turn it on again.
Troubleshooting Symptoms Cause & Solution Check the audio recording option is correctly set for the camera you wish to record audio. Audio data recorded with Check the speaker and audio (line input) on the rear of system are connected correctly. video data is not playing.
Troubleshooting Symptoms Cause & Solution E-mail reception failed without SMTP server setting. • Make sure the network is correctly set. • Make sure the mail address is input correctly. • Check the spam mail setting of the input mail address. (If you set the spam mail, some mails are deleted automatically or classified in the spam mail box) •...
Appendix Appendix Recommended Devices Recommended USB Memory list Maker Model Name Capacity LG Electronics XTICK SPIN LG Electronics XTICK UF1 32 G Lexar Jump Drive Memorive TRANSCEND 16 G SKYDRV SANDISK Cruzer 16 G Samsung Electronics SUM-LSB8 Samsung Electronics SUM-PSB...
Appendix Supported function list for device Device Instant backup Schedule backup Export Configuration Import/Export CD/DVD USB memory USB HDD E-SATA HDD NOTE If you use a USB memory stick or USB HDD for configuration import/export you must disconnect the other external USB devices. Supported PTZ Camera list Pan/Tilt Zoom...
Appendix Time zones Timezone Timezone name Timezone Abbreviation Eniwetok, Kwajalein -12:00 Midway Island, Samoa -11:00 Hawaii -10:00 Alaska -09:00 -08:00 Pacific Time (US and Canada); Tajuana -08:00 -07:00 Mountain Time (US and Canada), Chihuahua, La Paz, -07:00 -06:00 Mazatlan, Arizona Central Time (US and Canada), Saskatchewan, Guadalajara, Mexico City, Monterrey, -06:00 -05:00...
Appendix Factory Default Configuration Settings Factory Default 1st level 2nd level 3rd level Default Value setting System Name NULL Language The option depends on the model. Button Beep Video Format NTSC or PAL Properties Resolution 1024*768 Configuration Import Configuration Export Factory Default Convert (LRH7160, LRN8240) Interface...
Appendix Resolution 352x240 (NTSC) / 352x288 (PAL) Network Streaming Quality STANDARD Frame Rate 7.5 (NTSC) / 6 (PAL) Date Current Date Time Current Time Date Format YYYY/MM/DD Time Format 12 HR Date/Time Time Zone The option depends on the model. Daylight Saving Daylight Saving Start JAN, 1st, SUN, 00...
Appendix Name CH 01 to CH 24 Camera Audio 01 to 16, OFF IP Enable ON, OFF Channel CH 01 Port NONE Control ID Protocol LG_MULTIX Baud Rate 9600 PTZ Test 9 to 24 Name CH 09 to CH 24 Model Name NULL NULL...
Appendix Overwrite Full Warning Auto Delete Storage Saving Device Storage Format E-SATA Insert Eject Channel Name Channel Status Channel FPS Font Size Position Main Dwell Time 2 SEC Display Sequence Spot Dwell Time 2 SEC Channel CH 01 Brightness Video Adjustment Contrast Color Restore to Default...
Appendix Input Channel Transaction Start NULL Transaction End NULL ATM/POS Data Format Delimiter CARRIAGE RETURN Ignore String NULL Time Out 10 MIN Relay Output NONE Event Popup Spot Channel Sensor On Motion Detection Text In Notification Admin Password Changed Video Loss Power On/Off Disk Full Event...
Appendix SNMP Version NONE Port Community String public User NULL Authentication NONE SNMP Password NULL Privacy NONE Password NULL Trap IP Address NULL Event Trap Community String NULL Relay Off ALARM ACKNOWLEDGE System Alarm Out NONE Output HDD Fail Alarm Out NONE Video Loss Alarm Out NONE...
Appendix Specifications Model LRH7160D Series LRH7080D Series Analog Analog-IP Switch condition Analog-IP Switch condition Input - Basic : Analog 16ch + IP 8ch/4CIF - Basic : Analog 8ch + IP 8ch/4CIF or or Analog 8ch + IP 16ch/4CIF Analog 4ch + IP 12ch/4 CIF * Max.
Appendix Network Connection Ethernet 10/100/1000 Mbps (x2) Network Network Transmission Up to 240 IPS Bandwidth Control Power AC Free 100~240V, 50/60 Hz Power Consumption Maximum 80 W (with 6 HDD) Dimension (W x D x H) 440 mm x 452 mm x 115 mm Net Weight (without HDD) 9.68 kg 9.59 kg...