Genesis Platinum Alkaline Water Ionizer User Manual page 12

Installation Instructions
6) Insert one end of the other tubing half into the OUT quick connect connector on the
bottom of the Genesis. Make sure the tubing is pressed all the way into the connector
(IMPORTANT). Note: To remove tubing from a quick connect connector, push the ring
on the connector in (towards the body of the connector) and pull out the tubing.
7) Turn the connectors (and tubing) in the direction needed to exit the tubing towards the
sink.
8) Press the tubing into the guides at the edge of the Genesis bottom. Set the Genesis in an
upright position and place it where you intend to use it.
9) Both the "IN" tubing and the "OUT" tubing should be exiting the Genesis toward
sink. If they are not, lay the unit on its back and switch the direction of the connectors and
tubing accordingly.
10) Locate the stainless steel faucet head diverter valve and the stainless steel male/male
adapter and set these next to your sink.
11) Remove the existing aerator that is installed on your faucet head. Store this aerator in a
safe place in the event you need to use it at a later date.
12) Depending on what threads are your faucet head, you may or may not need to use the
male/male adapter to match the threads on the faucet head diverter valve. If required,
screw the adapter onto the faucet head. Then screw the faucet head diverter valve onto the
faucet head. Tighten securely.
13) Measure the length of the IN tubing needed to reach the diverter valve installed on the
faucet head.
14) With the Genesis placed where it will be used on a daily basis, take the IN tubing,
which is the tubing without the acid line sink attachment and run it to the pin on the faucet
head diverter valve. Do not pull on the tubing when measuring the length needed. You
want the tubing to have some slack so you can move the Genesis when cleaning the
counter top.
15) If your faucet head is designed to rotate, you will need to allow ample tubing for the
faucet to move freely once the tubing is attached to the faucet head. To do this, position
the faucet head at the point furthest from your Genesis. Mark the tubing with a marker and
cut at a square ninety degree angle with a razor blade or sharp knife, again leaving some
slack in the tubing.
Alkaline Water Ionizer
GENESIS Platinum
Installation Instructions
16) Press this IN tubing onto the pin of the faucet head diverter valve.
Position the tubing in the sink where you want it to drain (leaving some slack).
17) Mark the OUT tubing at the desired length with a marker and cut it with a razor blade or
sharp knife to the desired length.
18) Slightly wet the suction cup of the acid line sink attachment and the area of the sink where
you want to install the acid line and press the suction cup onto the wetted area of the sink.
19) Connect the Genesis ionized water output delivery hose to the Genesis. Screw the threaded
end of the deliver hose into the adapter on top of the Genesis. Tighten the hose securely.
Plug the Genesis power cord into a 110 Volt electrical outlet.
20) Adjust the input water pressure (water flow rate) into the Genesis using the faucet. You
want the water flow rate on the Genesis LCD Display to read between 2.0 and 2.5 liters/minute.
B) Cold Water Line Installation:
Note: Installing the optional water supply line diverter valve that is shipped with your Genesis
enables you to connect the Genesis IN quick connect connector on the bottom of the Genesis
directly to the cold water supply line under the counter. This eliminates the need to connect the
Genesis water supply tubing to the faucet. If you have an electrical outlet under the counter,
you can also plug the Genesis power cord into this outlet.
DRILLING the Access Hole
1) Determine where you want to place the Genesis on your countertop. You will want the
water output hose located on top of the Genesis to reach the sink. The access hole should be
relatively close to the Genesis in order to minimize the amount of tubing that will be exposed
above the counter.
2) Drill a 1/4" hole in the selected access hole location.
IMPORTANT: If you have an electrical outlet under the sink and you want to plug your
Genesis into this outlet (recommended if an outlet is available) you will need to make the
access hole large enough to accommodate both the Genesis power cord plug and the 1/4" water
supply tubing. DO NOT plug the Genesis in at this time.
3) TURN OFF the COLD water valve (usually the right hand valve).
GENESIS Platinum
Alkaline Water Ionizer