Page 1
8995UPC/DNC/UDX SD/HD UP/DOWN/CROSS CONVERTER Instruction Manual Software Version 1.3.0 071848005 MARCH 2011...
Page 2
Affiliate with the N.V. KEMA in The Netherlands CERTIFICATE Certificate Number: 510040.001 The Quality System of: Thomson Inc, and its wor dwide Grass Valley division affiliates DBA GRASS VALLEY Headquarters 15655 SW Greystone Ct. 10 Presidential Way 400 Providence Mine Rd...
Page 3
8995UPC/DNC/UDX SD/HD UP/DOWN/CROSS CONVERTER Instruction Manual Software Version 1.3.0 071848005 MARCH 2011...
Safety and Regulatory Compliance described in the GeckoFlex 8900 Series frame documentation (see the GeckoFlex Frames 8900FX/FF/FFN Signal Processing System Instruction Manual). All Modular product documentation can be found on-line in PDF format at this link: www.grassvalley.com/docs/modular 8995UPC/DNC/UDX — Instruction Manual...
Modules Introduction This manual covers installation, configuration, and operation for the 8995UPC Up Converter, 8995DNC Down Converter, and 8995UDX Up/Down/Cross Converter modules for the GeckoFlex frame. The 8995 modules provide up/down/cross conversion between broadcast quality SD and HD video. An optional Genlock submodule can be installed for external reference timing for environments requiring video signals to be synchronized with other video sources and processed for video quality.
Table 3 on page 28 for a video conversion summary diagram. 8995UPC Module The 8995UPC is fully featured with 8995 series functionality described above. This module up converts SD video to high quality HD video. Refer Table 4 on page 28 for a video conversion summary diagram.
(Figure 16 on page 37) and noting the software version given below the frame graphic. Check the Grass Valley ftp server at this link for the latest 8900NET release: ftp://ftp.grassvalley.com/modular/8900/8900net/v4.3.0/ Set Fan • Fans in the front cover must be set at maximum speed. Refer to Speed to Maximum on page •...
There are ten front and rear cell locations in the 2 RU GeckoFlex frame (Figure 1) to accommodate either audio, analog and digital video modules. The 8995 module set uses the 8900UDX-R rear module that requires two adjacent slots, allowing five 8995 modules per frame. Figure 1. GeckoFlex Frame 8995UPC/DNC/UDX — Instruction Manual...
The retainer clip screw torque specification is given in the specifications in Table 9 on page Mechanical • If using a fiber optic submodule, handle it carefully, use anti-static pre- Fiber Optic Cleaning Requirement on page 19 cautions, and read the before cabling. 8995UPC/DNC/UDX — Instruction Manual...
Manual available online for a complete overview of using the genlock reference. This as well as all other modular product manuals are available online at the following URL on the Grass Valley web site: http://www.grassvalley.com/docs/modular In addition to the capability of providing a local external reference to this...
All unused rear slots in a GeckoFlex frame should have a blank rear adapter cover installed. Figure 2. Installing Rear Module (751- Version Frame) Use retainer clip or needlenose pliers to pull out blank after removing retainer clips 8995UPC/DNC/UDX — Instruction Manual...
Install Genlock submodule on back of circuit board. Center submodule connector J1 over front module connector J14 and snap in place. From top side of module, tighten the screw provided to the standoff on the circuit board. 8995UPC/DNC/UDX — Instruction Manual...
For Frame Bus 1 distribution, set GEN LOCK BUS XMT jumper, J11 Pins 1-2 (ENA) or pins 2-3 (DIS). For Frame Bus 2 distribution, set GENLOCK BUS XMT jumper, J10 Pins 1-2 (ENA) or pins 2-3 (DIS). Pin 1 Pin 1 8995UPC/DNC/UDX — Instruction Manual...
Figure 5. Front Module Installation Card Carriers Front Module Side View Locking Pin Card Carriers Module installed Slide top and bottom card carriers on module over top and bottom guides on right of slot. 8995UPC/DNC/UDX — Instruction Manual...
This helps ensure optimum perfor- mance of the fiber optic interface. Industry standard fiber optic cleaning kits can be purchased on the web and in electronics stores. 8995UPC/DNC/UDX — Instruction Manual...
Page 20
Fiber Optic Receiver Handle Fiber Optic Transmitter Fiber Optic Transceiver Removing an SFP Submodule If you need to remove an SFP submodule, snap the handle out and pull the submodule slowly out of the metal cage. 8995UPC/DNC/UDX — Instruction Manual...
The input to the module can be connected to an electrical coax BNC and up to two fiber optic connectors depending on the fiber optic submodule installed. Only one video input can be active at a time and must be selected on the Video Input web page (page 54). 8995UPC/DNC/UDX — Instruction Manual...
Auto Tracking Output BNC J2 output is an auto tracking delay signal that can be fed to audio modules to synchronize the audio delay to match the delay of the 8995 module. 8995UPC/DNC/UDX — Instruction Manual...
Figure 5. Return the 8900NET module to the frame and replace the front cover. Figure 8. Set 8900NET S1 for Maximum Front Cover Fan Speed Remote Fan Speed Override at maxium Configuration DIP switch S1 8900NET 8995UPC/DNC/UDX — Instruction Manual...
PWR and (Figure 9) on the top side of the module front edge should illuminate (refer to Table 2 on page 25 to see the possible operating indi- cator combinations). Figure 9. Front Panel LED Indicators 8995UPC/DNC/UDX — Instruction Manual...
Page 25
VID IN (green) Indicates a valid input signal is being detected. Indicates no valid reference signal is being detected or signal is not locked. REF IN (green) Indicates a valid reference signal is present and locked. 8995UPC/DNC/UDX — Instruction Manual...
• Auto Blue – when Auto Blue is enabled on a channel, the output will automatically freeze to a blue screen when the input signal is lost on the input. 8995UPC/DNC/UDX — Instruction Manual...
1080i/50 to 576i/50 for example). • Cross Conversion – allows an HD signal input to be cross converted between progressive signal types and interlaced signal types in the same time domain (720p/59.94 to 1080i/59.94 or 1080i/50 to 720p/50 for example). 8995UPC/DNC/UDX — Instruction Manual...
Page 28
(50) 1080i Down Cross Convert Convert (50) Table 4 shows the possible input and output conditions for the 8995UPC Up Converter module or up conversion on the 8995UDX. Table 4. 8995UPC/8995UDX Up Conversion Output Signal 480i 720p 1080i 1080p 1080sf...
(white) and bottom (black) luminance levels and the white clipping on chrominance channel of the output signal (C White Clip) Image enhancement controls include a noise reduction control, edge expansion, extended color space, vertical edge filtering, and a matte edge border. 8995UPC/DNC/UDX — Instruction Manual...
Active Format Description on page 117. This Appendix provides detailed defini- tions of the binary codes and how the AFD codes respond to the aspect ratio settings made on the web page when AFD is present. 8995UPC/DNC/UDX — Instruction Manual...
Page 31
Figure 11. Full Height Aspect Ratio Shift horizontally Full Height (Center Cut) Complete picture appears in Full Height format with horizontal cropping. Also known as Center Cut mode. Position picture with horizontal alignment and cropping controls. 8995UPC/DNC/UDX — Instruction Manual...
Page 32
Set matte color of top and bottom margins. = lost picture Shift horizontally 14x9 SP: Up Conversion Top and bottom cropping; Position left, center, or right = lost picture 8995UPC/DNC/UDX — Instruction Manual...
Genlock Controls On modules with an 8900GEN-SM Genlock submodule installed (8995UDX+GEN, 8995DNC+GEN, or 8995UPC+GEN) the Genlock web page and control panel controls will be available. Use these controls to enable the external genlock reference and set control and timing parame- ters for the module.
The 8900NET module in the GeckoFlex frame should be running software version 4.3.0 or higher for optimum remote and control panel operation and is required for software updating. Upgrade software and instructions for the 8900NET can be downloaded from the Grass Valley web site. See System Requirements on page 11 for 8900NET software updating.
The available control panel controls for the 8995 modules are listed in Table 13 on page 111. An example of the Newton Configurator is shown in Figure Figure 15. Newton Configurator Example 8995UPC/DNC/UDX — Instruction Manual...
8900NET module with software version 4.3.0, using Internet Explorer, the recommended web browser, and Windows XP operating system. For information on status and fault monitoring and reporting shown on the Status page, refer to Status Monitoring on page 106. 8995UPC/DNC/UDX — Instruction Manual...
Page 37
Content display section displays the information page for the selected frame or module (frame slot icons are also active links). Refresh button for manual update of page 8995UPC/DNC/UDX — Instruction Manual...
Page 38
Status web page where Warnings and Faults are displayed. LED colors indicate: • Green = Pass – no problems detected • Yellow = Configuration error warning • Red = Fault condition detected 8995UPC/DNC/UDX — Instruction Manual...
Page 39
Figure 19. 8995UDX Status/ID Header When any of the 8995 modules have an 8900GEN submodule installed, the header shows the addition of the Genlock with + GEN (Figure 20). Figure 20. 8995UDX + GEN Status Web Page 8995UPC/DNC/UDX — Instruction Manual...
Page 40
• Frame Sync – provides horizontal and vertical timing and loss of signal controls for the 8995 module, multi-frame delay selection, minimum delay mode, manual freeze mode, and timing status tables (page 55), • Color Correction – provides RGB gain, offset and gamma correction adjustments (page 62), 8995UPC/DNC/UDX — Instruction Manual...
Page 41
(page 92), and • Slot Config – provides Locate Module and Slot Memory functions along with links to the SNMP, LED Reporting, and Frame Alarm con- figuration web pages (page 95). 8995UPC/DNC/UDX — Instruction Manual...
Information about the module, such as part number, serial number, hard- ware revision and software and firmware versions, and asset tag number (assigned on the Slot config web page) are given in a read-only section at the bottom of the display. 8995UPC/DNC/UDX — Instruction Manual...
Page 44
Configuration Figure 22. 8985UDX Status Web Page 8995UPC/DNC/UDX — Instruction Manual...
Page 45
Configuration Warnings and configuration errors are also reported on the Status web page between the double lines as shown in Figure Figure 23. Warnings and Configuration Error Reporting 8995UPC/DNC/UDX — Instruction Manual...
SNMP monitoring application such as NetCentral. Refer to Status Monitoring on page 106 for an explanation of the color coding and using an SNMP monitoring application. Note Outputs are not monitored in this application. 8995UPC/DNC/UDX — Instruction Manual...
Page 47
Configuration Figure 24. I/O Config Web Page with Factory Default Signal Names 8995UPC/DNC/UDX — Instruction Manual...
When a new configuration has been selected with the Input and Output Standard pulldowns, such as a up conversion operation shown in Figure 25, a message will appear indicating Changes Pending: Click Apply Set- tings button to commit changes Figure 25. Changes Pending Message 8995UPC/DNC/UDX — Instruction Manual...
Page 49
Configuration Figure 26. System Config Web Page 8995UPC/DNC/UDX — Instruction Manual...
Page 50
28. The warning message will indicate why this operation is not supported. Figure 28. Invalid Signal Conversion Warning Message Configuration errors on the System Config web page will also be reported on the Status web page as shown in Figure 23 on page 8995UPC/DNC/UDX — Instruction Manual...
Page 51
23.98Hz input video is synchronous to the start of the 10-field sequence in this reference. The 2:3 inverse pulldown cadence of 23.98Hz output video may be synchro- nized by the 8995UDX module to a SMPTE 318M-B reference. 8995UPC/DNC/UDX — Instruction Manual...
Page 52
This can be caused by a loss of one of the refer- ences or a mis-adjustment in the reference output delay of either reference. The total phase error shown in this graphic represents approximately 1 us. 8995UPC/DNC/UDX — Instruction Manual...
• Each configuration web page shown in the Functional View will have links to the web page, the web page, and the << Previous Functional View web page similar to Figure Next >> Figure 30. Configuration Web Page Links 8995UPC/DNC/UDX — Instruction Manual...
• – this field reports the status of the input video signal as Signal State Present Not Present , or Not Supported (no fiber submodule installed). Figure 31. Video In Web Page 8995UPC/DNC/UDX — Instruction Manual...
For normal delay operations, Minimum Delay mode should be disabled. Refer to Table 9 on page 99 for the delay values for each format. 8995UPC/DNC/UDX — Instruction Manual...
Page 58
Configuration Figure 34 illustrates the Frame Sync timing status when Minimum Delay Mode is enabled. Figure 34. Frame Sync with External Reference – Minimum Delay Enabled 8995UPC/DNC/UDX — Instruction Manual...
Page 59
• 150 pixels (Minimum Delay Mode selected) + Multi-Frame Delay + Delay Wrap Position (% of full scale) X (1 frame period). When converting from an interlaced to a progressive signal, the timing status will be noted as shown in Figure 35 on page 8995UPC/DNC/UDX — Instruction Manual...
Page 60
0 to 656 Must span input video frame period 1080p/23.98 1080i/59.94 0 to 2199 0 to 1406 Must span input video frame period 720p/59.94 0 to 1649 0 to 1874 Must span input video frame period 8995UPC/DNC/UDX — Instruction Manual...
Page 61
Configuration Figure 35 illustrates the Frame Sync timing status when upconverting between an interlaced and a progressive signal. Figure 35. Frame Sync with External Reference – Minimum Delay Enabled 8995UPC/DNC/UDX — Instruction Manual...
G Gamma Correction B Gamma Correction together using the control. Raising the gamma Total Gamma Correction above 1.0, brightens the gray intensity. Lowering the gamma below 1.0, darkens the gray intensity. Figure 36. Color Correction Web Page 8995UPC/DNC/UDX — Instruction Manual...
• – when Noise Reduction is enabled, control the level of noise Level reduction with the Level control from a very low level (0) to a high level (63). 8995UPC/DNC/UDX — Instruction Manual...
Page 64
2:2 cadence in the video, reducing the chance of dis- tortion related to cadence detection. The result may slightly reduce de-interlacing quality for 3:2 cadence video. 8995UPC/DNC/UDX — Instruction Manual...
Page 65
Configuration Figure 37. Video Proc Web Pager 8995UPC/DNC/UDX — Instruction Manual...
It can also detect the presence of EIA608 CC inside of an EIA708 digital packet. In the Transcoding web page, the controls for CC Transcoding are divided into three sections: • Input Status, • Encode to Output, and • Output Signal. 8995UPC/DNC/UDX — Instruction Manual...
Page 67
In this case, the user may select with the control, Encode to Output which packet type ( , or take the closed Digital 708 CC Digital 608 CC Analog CC) to captioning from. 8995UPC/DNC/UDX — Instruction Manual...
Page 69
Analog CC or place the Analog CC (normally on Line 21) on any line between lines 11 and 21. Lines 6-10 and Line 22 are reserved for digital only. Figure 40. Encode to Output Pulldown 8995UPC/DNC/UDX — Instruction Manual...
Page 70
Lines 6-22. (Default) Line 21 Note Lines 9 is reserved for the EIA708 Default and Line 12 is reserved the EIA608 Default. Figure 41. Analog Output Line Choices 8995UPC/DNC/UDX — Instruction Manual...
VITC Analog VITC Input Line input line for VITC detection on a specific line or the default position of . The Input Line pulldown choices are shown in AUTO DETECT Lines 7-19 Figure 43 on page 8995UPC/DNC/UDX — Instruction Manual...
Page 72
VITC will be on in Output Line the output video signal. Select a specific line or default position of AUTO . The Input Line pulldown choices are shown in Figure DETECT Lines 7-19 Figure 44. VITC Output Line Choices 8995UPC/DNC/UDX — Instruction Manual...
AFD Control section. When disabled, the AFD Input/Output reporting on the web page will be bypassed. The Aspect Ratio mode selection, , will also be removed and revert to Auto Full Width mode as shown in Figure 46 on page 8995UPC/DNC/UDX — Instruction Manual...
Page 74
SMPTE AFD requirements. Refer to the Appendix, Active Format Description on page 117, for detailed information on SMPTE AFD code definitions and requirements and how to use the aspect ratio controls with signals containing AFD information. 8995UPC/DNC/UDX — Instruction Manual...
Page 75
Configuration Figure 45. Aspect Ratio Web Page without AFD Auto Mode is present but not active 8995UPC/DNC/UDX — Instruction Manual...
Page 76
Configuration Figure 46. Aspect Ratio Web Page with AFD Disabled Auto Mode is removed 8995UPC/DNC/UDX — Instruction Manual...
Page 77
Configuration Figure 47. Aspect Ratio Web Page with AFD Present and Enabled 8995UPC/DNC/UDX — Instruction Manual...
Transmitter or a Transceiver submodule. • – checking this checkbox enables re-embedding of Audio Re-Embedding the audio on the output signal. For no embedded audio on the output, leave this unchecked. Figure 48. Fiber Out Web Page 8995UPC/DNC/UDX — Instruction Manual...
• – reports whether the detected audio has 20 or 24 bit capability. Capability • – identifies the detected audio as Audio or Non-audio. Audio Mode Figure 49. Audio Input Status Web Page this link 8995UPC/DNC/UDX — Instruction Manual...
Use the Delay controls for Channel A and Channel B to adjust the indi- vidual channel delay from ±33.786ms (29.97Hz), ±40ms (25Hz), and ±41.708ms (24Hz) with respect to video delay. To lock the channel delay setting together, select the Channel Delay Lock checkbox. 8995UPC/DNC/UDX — Instruction Manual...
> -42 dBfs is present. False indicates the signal exceeds this level or is not present. • Under , a report of indicates that the signal is clipping above Clip True -0.5dBfs. indicates the signal is > -0.5 dBfs. False 8995UPC/DNC/UDX — Instruction Manual...
Page 83
Configuration Figure 51. Audio Gain Web Page 8995UPC/DNC/UDX — Instruction Manual...
Present Not Present Use the radio buttons to select which Groups (1-2) Groups (3-4) View Select audio pairs to define. The resulting choices will be the embedded audio configuration in the video output signal. this link 8995UPC/DNC/UDX — Instruction Manual...
• 1 KHz • 400 Hz • Silence Note To re-embed the processed audio into the video output stream, make sure the Audio Re-Embedding Enable checkbox on Video Out Web Page on page 78 is selected. 8995UPC/DNC/UDX — Instruction Manual...
For example, if Low Jitter is selected and the Status is still after Invalid one minute has passed, the input reference has excessive wander that cannot be tracked in Low Jitter mode. Switch to and verify Fast Lock Status is after about 10 seconds. Locked 8995UPC/DNC/UDX — Instruction Manual...
Page 89
– provides coarse adjustment of the reference timing stream Coarse Offset by 37 ns steps up to one line. • – provides fine adjustment of the reference timing stream by Fine Offset steps up to 37 ns. Figure 54. Genlock Web Page 8995UPC/DNC/UDX — Instruction Manual...
Page 90
720p 50 TLS 1080p 24 TLS 1080sf 24 TLS 1080 sf 24 TLS Not used in this release 1080i 50 TLS 720p 50 TLS 1080p 23.98 TLS None NTSC 1080p 23.98 TLS 1080i 59.94 TLS 720p 59.94 8995UPC/DNC/UDX — Instruction Manual...
Page 91
None AES 48K Word Clock 96K AES 96K Work Clock 48K This input standard will lock but will generate a Warning on both the Genlock and Status web pages but will not affect the locked condition. 8995UPC/DNC/UDX — Instruction Manual...
2. In the File Download screen select Save 3. This will bring up the Save As screen shown in Figure 56 on page 4. Enter a name in the File name field. This file is saved as a .bin type. 8995UPC/DNC/UDX — Instruction Manual...
Page 93
2. Enter a path and file name or select to locate the directory Browse... where the files have been saved. Figure 57. Load Settings Configuration. 3. This will bring up the Choose File screen shown in Figure 58 on page 8995UPC/DNC/UDX — Instruction Manual...
Page 94
As mentioned in a previous note, recalling default factory settings and names must be done after any software update. This writes over your current con- figuration so follow the instructions for saving your configuration before updating software. 8995UPC/DNC/UDX — Instruction Manual...
• Locate Module • Slot Identification • Slot Memory • Frame Health Reporting • LED Reports • SNMP Trap Reporting Each of these functions is described in detail below. Figure 59. Slot Config Web Page this link 8995UPC/DNC/UDX — Instruction Manual...
Page 96
Learn Module Config current configuration for this slot. The configuration is saved on the 8900NET module. If the 8900NET module is removed or powered down, the stored configurations are not saved. 8995UPC/DNC/UDX — Instruction Manual...
Page 97
8900NET module. This web page allows configura- tion of which alarms and warnings that are reported to the SNMP manage- ment software. Refer to the 8900NET Instruction Manual for complete details on using the 8900NET web pages. 8995UPC/DNC/UDX — Instruction Manual...
Refer to the latest module release notes for complete software updating details. All modular Modular product documentation, including the latest release notes, can be found in PDF format on the Grass Valley web site at this link: www.grassvalley.com/docs/modular 8995UPC/DNC/UDX — Instruction Manual...
140 ps for HD 500 ps for SD Output jitter < 0.2 UI > 100KHz for HD (FS mode, in low jitter mode) < 1.0 UI 10 Hz-100KHz for HD < 0.2 UI 10 Hz and up for SD 8995UPC/DNC/UDX — Instruction Manual...
Page 100
Delay not deterministic Input 0.4 to 3.2 Genlock 1 frame 1 to 8 1080p/sf/23.98 – 1080p/23.98 Input 1 frame 1 to 8 Genlock 1.2 to 10.0 1080p/sf/23.98 – 480i/59.94 Delay not deterministic Input 1.2 to 10.0 8995UPC/DNC/UDX — Instruction Manual...
Page 101
Input 0.5/1.0 frames 0.5 to 4.0 Genlock 0.5 frames 0.5 to 4.0 720p/50 – 1080i/50 Input 0.5/1.0 frames 0.5 to 4.0 Genlock 1 frame 1 to 8 720p/50 – 720p/50 Input 1 frame 1 to 8 8995UPC/DNC/UDX — Instruction Manual...
Page 102
1080p/sf/23.98 – 1080p/sf/23.98 Input 2 frames 2 to 9 Genlock 2.4 to 11.25 1080p/sf/23.98 – 480i/59.94 Delay not deterministic Input 2.4 to 11.25 Genlock 2.4 to 11.25 1080p/sf/23.98 – 1080i/59.94 Delay not deterministic Input 2.4 to 11.25 8995UPC/DNC/UDX — Instruction Manual...
Page 103
2 adjacent front and rear slots Rear module type 8900UDX-R Rear module retainer clip screw torque 4-5 inch-lb./0.45-0.6Nm Environmental Frame temperature range Refer to GeckoFlex Frames 8900FX/FF/FFN Signal Processing Operating humidity range Systems Instruction Manual at: www.grassvalley.com/docs/modular Non-operating temperature 8995UPC/DNC/UDX — Instruction Manual...
Page 104
For Input-Timed Mode: table entries indicate the delay in output video frame start from the input video frame start position. 8995UPC/DNC/UDX — Instruction Manual...
Page 105
-5 to 0 dBm (-2dBm typical) Maximum distance 10 km Maximum distance 20 km The 1310 nm Dual Transmitter (SFP-13103G-M1DTX) and Transceiver (SFP-13103G-M1TRX) require no attenu- ation between fiber transmitter and receiver connections at any length. 8995UPC/DNC/UDX — Instruction Manual...
• LEDs on the Frame, 8900NET module, and individual frame media modules, • Web browser status reporting for each frame component, and • SNMP traps, captured by Grass Valley’s NetCentral or another SNMP Manager Application. Note SNMP trap information is only available when an SNMP Agent has been installed and configured.
When SNMP Agent software is installed on the 8900NET module, enabled status reports are sent to an SNMP Manager such as the Grass Valley’s NetCentral application. Status reporting for the frame is enabled or disabled with the configuration DIP switches on the 8900NET module.
If power has been cut off to module, remove the module and replace it in the frame to reset. If the problem persists contact Grass Valley Customer Service.
Auto Auto or Manual Reference Restore RefSwBk method Switch to Primary pulldown System Config/ Select amount of delay for switching 30 seconds 30 to 93.97 seconds Reference Restore RefSwDly back to primary Reference Switchback Delay (Seconds) 8995UPC/DNC/UDX — Instruction Manual...
Page 112
Adjust color saturation 0 to 200% 100% Video Processing Controls Chro Gn (chroma gain) (1% steps) Color Saturation (%) Video Proc/ 0 to 200% Adjust total gain 100% Video Processing Controls VPA Gain (1% steps) Total Gain 8995UPC/DNC/UDX — Instruction Manual...
Page 113
Enable or Disable Image Enhancement Controls/ MatBdrEn Matte Edge Border Enable checkbox Auto, Transcoding/ CC (closed captioning) transcoding Digital 708 CC, Auto CC Transcoding/ AudTrscdEnab input signal Digital 608 CC, or Input Signal radio buttons Analog CC. 8995UPC/DNC/UDX — Instruction Manual...
Page 114
Audio Re-embedding Enabled Checkbox Audio Disruption Processing (enabled turns off V-fade and X-fade Audio Delay/ Disabled Enabled or Disabled AudDunkEn to eliminate pops and clicks on out- Audio Disruption Processing checkbox puts). 8995UPC/DNC/UDX — Instruction Manual...
Page 115
View Select (Note: Audio Re-embedding check- Group 3, Group 1, Group 2, Group 3, or Group 4 box on Video Out web page must be or Group 4 radio button checked to re-embed audio to out- put. 8995UPC/DNC/UDX — Instruction Manual...
Page 116
Drive Frame Reference Bus pulldown User Settings/ Recall factory default parameters See Defaults column Recall Factory Defaults Set Factory Defaults button User Settings/ Recall factory names See I/O Config web page Recall Factory Defaults Set Factory Names button 8995UPC/DNC/UDX — Instruction Manual...
When a 4:3 or 16:9 input signal is passed through the module with no up, down, or cross conversion, the AFD Input Code will be the same as the AFD Output Code. 8995UPC/DNC/UDX — Instruction Manual...
SDI. If the output offset turns out to be too large, AFD data is inserted 4 lines after the switching line. When there is a video freeze, AFD is not inserted. 8995UPC/DNC/UDX — Instruction Manual...
When Mode = , the module software is programmed to attempt to pre- Auto serve full height while keeping as much vertical information as possible while following the SMPTE AFD standard. Figure 65. AFD Output Code = 1001 8995UPC/DNC/UDX — Instruction Manual...
Page 120
Active Format Description Figure 66. AFD Present in Input Signal 8995UPC/DNC/UDX — Instruction Manual...
Page 121
This AFD Output Code, , produces an image with a 14x9 aspect ratio 1011 as a horizontally centered pillarbox image in a 16:9 coded frame similar to the image in Figure Figure 67. AFD Output Code = 1011 8995UPC/DNC/UDX — Instruction Manual...
Page 122
Active Format Description Figure 68. Change AFD Output Code 8995UPC/DNC/UDX — Instruction Manual...
Image is full frame with an aspect ratio that is the same as the 4:3 coded frame. Full Frame AFD = 1010 Image with a 16:9 aspect ratio as a vertically centered letterbox in a 4:3 coded 16:9 frame. (center) 8995UPC/DNC/UDX — Instruction Manual...
Page 124
4:3 coded frame. (with alternative 14:9 center) AFD = 1111 Image with a 16:9 aspect ratio and with an alternative 4:3 center as a vertically 16:9 centered letterbox in a 4:3 coded frame. (with alternative 4:3 center) 8995UPC/DNC/UDX — Instruction Manual...
Image with a 14:9 aspect ratio as a horizontally centered pillarbox image in a 16:9 14:9 coded frame. (center) AFD = 1101 Image with 4:3 aspect ratio and with an alternative 14:9 center as a horizontally (with alternate 14:9 centered pillarbox image in a 16:9 coded frame. center) 8995UPC/DNC/UDX — Instruction Manual...
Page 126
Image with a 4:3 aspect ratio and with an alternative 14:9 center in a 4:3 coded (with alternative frame. 14:9 center) AFD = 1111 16:9 Image with a 16:9 aspect ratio and with an alternative 4:3 center in a 16:9 coded (with alternative frame. 4:3 center) 8995UPC/DNC/UDX — Instruction Manual...
Aspect Ratio web page summary table Output Status reporting auto tracking output reporting status Analog Input Line control aspect ratio 14x9 SP blank rear cover definition AFD (Active Format description) anamorphic definition cabling Center Cut cadence controls 8995UPC/DNC/UDX — Instruction Manual...
Page 138
GeckoFlex frame Encode to Output control frame alarm extended color space control module placement Genlock Loop cabling I/O Config web page factory default names Genlock submodule 8995UPC/DNC/UDX — Instruction Manual...
Page 139
Names and Meanings table summary table Local/Remote jumper outputs operation coax Locate Module function fiber optic loss of signal reporting operation, remote control operation, summary table remote controls power up summary table Primary-Secondary Phase Difference PWR LED 8995UPC/DNC/UDX — Instruction Manual...
Page 140
System Config web page transcoding system configuration remote controls system requirements web browser links overview transcoding recommended closed caption web site overview documentation summary of controls FAQ database VITC Grass Valley Transcoding web page software download troubleshooting 8995UPC/DNC/UDX — Instruction Manual...