Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stevens AeroModel LiddleRod 2.4
Summary of Contents for Stevens AeroModel LiddleRod 2.4
- Page 1 Micro RC Model for Spektrum / ParkZone 2.4 systems Length 12.5 inches | Span 14.75 inches | Wing Area 57 inches | Flying Weight 1.1 oz. Photo Supplement for Plans Dated 03.08.2010 LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 1 of 14...
-
Page 2: Product Support
Product Support WARRANTY Stevens AeroModel guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall Stevens AeroModel’s liability exceed the original cost of the purchased kit. Further, Stevens AeroModel reserves the right to change or modify this warranty without notice. -
Page 3: Kit Contents
Covering Iron and Heat Gun Small Needle Nose Pliers Small Round “Rat-Tail” file. 1 in. x 2 in. length sticky back velcro 3/4 in. wide clear tape 1 Roll AeroLITE (solite) LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 3 of 14... - Page 4 General Assembly Instructions Thank you, for purchasing this Stevens AeroModel LiddleRod™. An indoor micro RC model developed for the popular Spektrum and ParkZone 2.4ghz micro receiver/esc/servo “brick” or “puck” systems. This model has been developed and manufactured using state of the art CAD/CAM systems and features a unique interlocking construction process that, when compared to traditional methods found in other model aircraft kits, save countless hours of measuring, cutting, sanding, and fitting.
-
Page 5: Fuselage Construction
Fit left fuselage side FR to assembly and tack In the same manner dry fit F4... glue. Fit and tack glue part F5 to top of fuselage..Then F1 to the assembly. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 6 of 14... - Page 6 Square fuselage on flat mount. surface and glue all joints with thin CA. Fit G1 behind F2... Match profile of F8 with that of F1 and glue in place. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 7 of 14...
- Page 7 V5 1/32 in. ply disks. Fit vertical stabilizer to slots in fuselage assembly. Align stabilizer perpendicular to fuselage top and glue. Bend landing gear per plan sheet and fit to gear block. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 8 of 14...
- Page 8 CA. Do not allow glue to contact nylon wheel within pants. Tack parts in ascending order from work table up. Align edges and glue. Bevel leading edges of rudder and elevator. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 9 of 14...
- Page 9 Clip prongs from motor gear box and lightly with double sided tape. Make and install sand tabs smooth. push rods per push rod detail on wing assembly plan page. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 10 of 14...
-
Page 10: Wing Construction
Fit and glue parts W1a and W1b together. Glue pilot cut-outs to balsa figure part P with contact cement. Fit and glue rib R2 to slot in leading edge of wing. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 11 of 14... - Page 11 Fit S1/R1 assembly to slot in rib R2 and wing frame. Align and secure with thin CA. tape the leading edge to the work surface, then wrap the frame over the ribs and glue at trailing edge. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 12 of 14...
-
Page 12: Final Assembly
CA glue along the top and bottom lacquer based spray - We recommend Deft, root edge and within the fuselage along the available at your hardware store. spar tab. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 13 of 14... - Page 13 Follow the directions in step 4 of Final Assembly instructions on plan set for installation. Show your completed LiddleRod™ off to friends and family. LiddleRod™ © 2010 Stevens AeroModel all rights reserved. Page 14 of 14...
Need help?
Do you have a question about the LiddleRod 2.4 and is the answer not in the manual?
Questions and answers