Table of Contents
Advertisement
-
- - - -
I
RECORDING
~
•
Insert a recordable CD,
printed side up
and close the compart
men\.
-
CLOSe
lights up and the display
w
ill show the number of
recorded tracks and and the total recorded time
.
OPC
will light up if the CDR is loaded for the first time; the
rec order then adapt the power of the
laser
to this particular.
CDR
(Cpe
= Optimum
Power
Calibration).
•
Press RECORD to set the recorder to the
recording/stand-by
mode
.
-
The RECORD indication (red led above the button) starts
flashing;
r
u~
L
lights up if the CD is
full.
ANALOG RECORDING
•
Select ANALOG with the INPUT SELECT button.
- You can now record from an
y
analog source
.
You can also
make an analog recording from a dig ital source, for example
from a digital CD which you have recorded yourself In this
case
ensure
that
the CD player and the recorder are connected
with each
ot
ner via the
analog
inputs and
outputs.
•
Allow the so urce from which you wish to record, to
play.
•
Set the volume with REC(ording) LEVEL so that the LEDs in
the display light up during passages with an average volume
ofupto-10dB.
An excess of up to
-
3dB
is
norma
l
during peaks.
•
Differences between the left and right channel can be
corrected w ith the BALANCE control.
•
Press
PLAY
to start recording.
- The track being played/recorded is always shown under
TRACK and on the number
indicator,
and its elapsed
playing/recording time is shown under TRACK TIME
.
- When automa tic track numbering (AUTO) is selected,
recording
will stop automatically after the last track.
When manual tra
c
k numbering (MANUAL) is selected
,
you
must stop recording by pressing STOP/CM
•
If you do
not
yet wish
to
store the recording permanently
(FI
X
UP), you can rem ove the CDR and add to the recording
at any
time
or skip unwanted passages and/or tracks.
• If
you do not wish
to
record anything else on the CDR you
can store the recording permanently by pressing FI
X
UP and
then
within 2 seconds
REC(ord)
- FIX LIP lights up; the recording will now be stored
.
The time
needed for this will be counted down on the display
- The recording has
now
been st ored on the CDR and can
no
longer
be changed
.
•
Press OPEN/CLOSE to open the CD compartment and take
out the CDR
.
•
Press POWER to switch the recorder off.
10
DIGITAL RECORDING
•
Select DIGITAL with the INPUT SELECT button
.
- You can now record fr om any (digital) CD(V) player.
•
You do not need to set the recording
level;
the signal is
taken over exactly from the original.
•
Press PLAY to start recording.
-
The track being played/recorded is always sh own under
TRACK
and on the number indicator, and Its elapsed
playing/recording time IS
show
n under TRACK
TIME.
- When automatic track numbering (AUTO) is selected,
recording
w
ill stop automatically after the last track
.
When manual track numbering (MANUAL) is
selected,
you
must stop recording by pressing STOP/CM
.
-
If
you do not yet wish to store the recording
permanently,
you can remo ve the CDR and add to the recording at any
time or skip unwanted passages and/or tracks.
•
If you do not wish to store anything else on the CDR, yo
u
can store the recording permanently by pressing
FIX
UP
and
then
within 2 seconds
REC(ord).
- FI
X
UP
lights
up;
the
recording
w
ill now be st
ored.
The time
needed for this will be counted do
w
n on the display
-
The
recording has now been stored on the CDR and can
no
longer
be changed.
•
Press
OPEN/
CLOSE to open the CD compartment and take
out the CDR.
•
Press POWER to switch
the
recorder off.
SYNCHRONIZED RECORDING
(REC SYNC)
If the recorder is connected via the RC5 REMOTE sockets to a
CDM player
w
ith a REC SYNC function you can synchronize
the start of recording and playback
.
NOTE!
This function is only possible when the PAUSE mode of the
CD player is cancelled by pressing
the
PAUSE button againl
• Press
REC SYNC on the recorder.
-
REC SYNC lights up.
•
Press RECORD to set the rec order to the recording/stand-by
mode
.
•
Press PLAY on the recorder.
-
Playback and recording will start at the same time
.
- When automatic track numbering (AUTO) is selected,
recording will stop automatically after the last track.
When manual track numbering (MANUAL) is selected, you
must stop recording by pressing STOP/CM.
RECORDING A SILENT PASSAGE
(MUTE)
•
Press RECORD to set the
reco
rder to the recording/stand -by
mode.
•
Press MUTE
- A 3-second pause will
now
be recorded
.
- The pause time will be counted down on the
display.
RECORDING VIA (A) MICROPHONE(S)
•
Connect a microphone
w
ith a 6.3 mm jack plug to the
MICRO L/MONO socket if you wish to make a mono recording.
•
Connect one microphone With a 6.3 mm jack plug to each of
the MICRO
soc
kets (L/MONO and R) if you wish to make a
stereo recording.
•
Select ANALOG with the INPUT SELECT button (27) on the
front of the recorder.
•
Set the
INPUT
SELECT SWitch (12) on the rear of the player
to
MICRO.
•
You can now record you
r
voice
.
•
Adjust the recording volume using the RECORD LEVEL
button
c,
t
J
IN·
•
f
•
f
ST
•
F
- F
SK
aL
th
ar
Ski
•
I r
•
P
-
s
It
-T
•
A
S
•
P
-T
ri
Un!
•
Ir
·
P
,
"
-
LJ'
-
TI
•
A
S
\
•
P
-
TI
[P,
C ?
\
skir:
./
Advertisement
Table of Contents
