Warranty - Elation TVL2000 User Instructions

TVL2000
2-YEAR LIMITED WARRANTY
A. Elation® Architectural hereby warrants, to the original purchaser, Elation®
Professionals® products to be free of manufacturing defects in material and
workmanship for a period of two years (730 days) from the date of purchase. This
warranty shall be valid only if the product is purchased within the United States
of America, including possessions and territories. It is the owner's responsibility
to establish the date and place of purchase by acceptable evidence, at the time
service is sought.
B. For warranty service, send the product only to the Elation® Professionals®
factory. All shipping charges must be pre-paid. If the requested repairs or ser-
vice (including parts replacement) are within the terms of this warranty, Ela-
tion® Professionals® will pay return shipping charges only to a designated point
within the United States. If the entire instrument is sent, it must be shipped in
its original package. No accessories should be shipped with the product. If any
accessories are shipped with the product, Elation® Professionals® shall have no
liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the
product is modified in any manner which Elation® Professionals® concludes,
after inspection, affects the reliability of the product; if the product has been
repaired or serviced by anyone other than the Elation® Professionals® factory
unless prior written authorization was issued to purchaser by Elation® Profes-
sionals®; if the product is damaged because not properly maintained as set forth
in the instruction manual.
D. This is not a service contract, and this warranty does not include mainte-
nance, cleaning or periodic check-up. During the period specified above, Ela-
tion® Professionals® will replace defective parts at its expense, and will absorb
all expenses for warranty service and repair labor by reason of defects in mate-
rial or workmanship. The sole responsibility of Elation® Professionals® under
this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of Elation® Professionals®. All products
covered by this warranty were manufactured after January 1, 1990, and bear
identifying marks to that effect.
E. Elation® Professionals® reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes
in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to
any accessory supplied with products described above. Except to the extent
prohibited by applicable law, all implied warranties made by Elation® Profession-
als® in connection with this product, including warranties of merchantability or
fitness, are limited in duration to the warranty period set forth above. And no war-
ranties, whether expressed or implied, including warranties of merchantability or
fitness, shall apply to this product after said period has expired. The consumer's
and or Dealer's sole remedy shall be such repair or replacement as is expressly
provided above; and under no circumstances shall Elation® Professionals® be
liable for any loss or damage, direct or consequential, arising out of the use of,
or inability to use, this product.
G. This warranty is the only written warranty applicable to Elation® Profession-
als® Products and supersedes all prior warranties and written descriptions of
warranty terms and conditions heretofore published.
©Elation Pr fessionals® - www.elationlighting.com - TVL2000 Instruction Manual Page 16
o

Warranty

TVL2000
Power Supply:
electronic ballast, which will auto sense the voltage when it is plugged
into the power source. With the electronic ballast you do not need to
worry about wall voltage, this unit can be plugged in anywhere. Also
be sure to only use the included I.E.C. power cable supplied with the
unit.
DMX-512:
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA "IN" and DATA "OUT" XLR terminals located on all DMX
fixtures (most controllers only have a DATA "OUT" terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a sin-
gle controller, as long as all fixtures and the controller are DMX com-
pliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The TVL2000 3 DMX channel modes. The DMX address
is set electronically using the controls on the side of the unit. Your unit
and your DMX controller require a approved DMX-
512 110 Ohm Data cable for data input and data
output. We recommend Accu-Cable DMX cables.
If you are making your own cables, be sure to use
standard 110-120 Ohm shielded cable (This cable
may be purchased at almost all professional sound
and lighting stores). Your cables should be made
with a male and female XLR connector on either
end of the cable. Also remember that DMX cable
must be daisy chained and cannot be split.
©Elation Pr
The Elation Professionals
DMX is short for Digital Multiplex. This is a universal pro-
fessionals® - www.elationlighting.com - TVL2000 Instruction Manual Page 5
o
Set Up
TVL2000 contains an
®
Figure 1