Connecting the Battery Connecting the Charger IMPORTANT: Even if you have the Basement Watchdog Special Backup Sump Pump System installed by someone else, you must read and follow the safety information contained in this manual. Failure to do so could result in property damage, serious injury, or death.
SMALLER DIAMETER that they will be easily accessible. cause battery to explode in enclosed spaces. When service is required, contact Glentronics Charge in a well-ventilated area. Always • When connecting the battery cables, first technical support at 800-991-0466, option #3, Failure to read and follow these warnings and shield eyes and face from battery.
Introduction Control Unit The Basement Watchdog Special backup sump pump system is battery-operated. It is designed as an emergency backup system to support your main AC sump pump, and it will automatically Battery begin pumping any time the float switch is...
Pump & Pipe NORMAL SUMP PIT Installation Instructions INSTALLATIONS FLOOR FLOOR There are two basic methods that can be used to JOIST JOIST install the pump, a direct discharge to the SLOPE PIPE outside of the building, or a connection to an DOWN existing discharge pipe.
Pump & Pipe the pump to any existing pipes; it should be in place of the union. Make sure it is placed on the floor of the sump. A brick may installed with the arrow pointing up, or it Installation Instructions be placed under the pump if there are rocks will not prevent the backflow of water.
Pump & Pipe Installation Instructions INSTALLATION B: CONNECTION TO AN EXISTING DISCHARGE PIPE (Diagram B) Depending on your installation requirements, PVC pipe lengths will vary. Cut the pipes and assemble them as shown in photo #7. Do not cement them together until you are sure they are cut to the correct lengths.
Pump & Pipe the “L” bracket. (c) Once the strainer is prevent leaking. (No check valve is needed with prevent the backflow of water. When a check this method of installation as long as you use attached, simply press the rest of the pump valve is used, a 1/8”...
Page 8
Pump & Pipe the main AC pump with two (2) stainless steel 5. Install a check valve on the top of the PVC bottom of a “Y” connector. Prime and cement hose clamps. Position the bracket so the pipe attached to the Basement Watchdog the top of the “Y”...
Battery Instructions purchased the battery. time and give off a sulfur-like smell, but this is normal. After the battery has been filled, screw NOTE: BASEMENT WATCHDOG BATTERIES NOW the six (6) caps securely on the top of the battery. A new Basement Watchdog 7.5 Hour Standby COME IN TWO CONFIGURATIONS.
and cut off the tip. Insert the end of the hose Control Unit Connections into each cell. Control the flow by pinching the hose with thumb and forefinger. Fill each DANGER cell of the battery to a level just covering Risk of electrical shock or battery explosion, the battery plates, and then go back and which can cause serious injury or death.
security tag from the battery cables. Attach CAUTION the battery cables to the battery…the BLACK wire to the NEGATIVE (-) post, and the RED If you are not using the Basement Watchdog wire to the POSITIVE (+) post. Replace the Standby battery, you cannot use the battery PUMP wing nuts and tighten them.
The Basement Watchdog Special allows you to • If the bottom light on the controller is also The Basement Watchdog control unit features a connecting it to your car battery.
REFER TO THE PHOTOS AT LEFT REPLACING THE BATTERY DANGER 1. Unplug the charger from the wall outlet. Risk of electrical shock or battery explosion, 2. Remove the cover of the battery box by which can cause serious injury or death. pushing in the tabs on the front and back, Wear eye protection.
Page 14
See enclosed order form.) battery. Then call Glentronics technical 9. Plug the charger back into the wall outlet. support for instructions at 800-991-0466, Remove (You should provide additional protection for 6.
Pump When the water rises in the sump pit and PUMP CH RGER activates the float switch, the pump will begin FUSE pumping, and the “Pump was activated” light and alarm will turn on. Try to determine what caused the system to activate. •...
YELLOW button for 5 seconds. It is important to manually test the float The alarm will be silence, but the light will stay The Basement Watchdog Special is equipped switch periodically. on. The system will continue to operate while with a computer-controlled automatic charging the power alarm is silenced.
Troubleshooting Guide Read safety warnings & instructions before attempting any repairs or maintenance. DANGER BATTERY ALARM Possible Reasons Remedies Terminals are corroded ....Clean terminals &...
The defective product must be returned directly to the factory, postage prepaid with the original bill of sale or receipt to the address listed below. Glentronics, Inc., at its option, will either repair or replace the product and return it postage prepaid.
Page 19
CHECK OUT THESE OTHER BASEMENT WATCHDOG PRODUCTS AC PUMPS FLOAT SWITCHES CHECK VALVES WATER ALARMS Industrial Grade Pumps for the What’s the most common reason your What’s a Klunkless Check Valve™? Minimize the risk of water damage Residential Market main AC pump fails? If you’ve spent any time in your basement, You can detect leaks before they become bigger The Basement Watchdog line of AC sump pumps...