Technical Support personnel can more effectively assist you. Safety Instructions ATTENTION: To safely interact with and enjoy all the features and benefits of these Xtreme Power Conversion Un- interruptible Power Supplies (UPS), please read and follow all installation and operation instructions completely.
Page 4
See Page 15 of this manual for more safety details. DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! Xtreme Power does not sell products for life support or medical applications. DO NOT use these UPS in any circumstances that would affect operation or safety of any life support equipment or with any medical applications or patient care.
• If AC input power fails, the inverter turns on an supplies power from the batteries to the load. • When AC input power returns, the UPS automatically begins supplying the load with power through the AVR circuit. • The charger circuit provides recharge for the batteries. Xtreme Power Conversion Corporation Page 5...
Page 6
XVRT User’s Manual Uninterruptible Power Supply Xtreme Power Conversion Corporation Page 6...
Page 7
XVRT User’s Manual Uninterruptible Power Supply XVRT-1000 FRONT PANEL Xtreme Power Conversion Corporation Page 7...
Page 8
Caution: To reduce risk of fire, use only 26AWG or larger telecommunication line cord. Communication Function A RS232 interface and UPSMON software is provided to support communications with NOVELL, UNIX, DOS, WIN- DOWS, and other operating systems. Xtreme Power Conversion Corporation Page 8...
Note: Many factors can affect the amount of power that your computer system will require. The total load that you will be placing on the battery-powered outlets should not exceed 85% of the UPS capacity. Xtreme Power Conversion Corporation Page 9...
Inspect the UPS upon receipt. The packaging is recyclable; keep it for reuse of dispose of properly. Installation of Rack-mount accessories Install the rack-mount type units according to the following illustrations. Vertical Tower Configuration Wall Mount Configuration Horizontal Stacked Configuration Xtreme Power Conversion Corporation Page 10...
UPS output outlets, as its power demand is much higher than typical peripherals and may cause the circuit breaker to trip. It is suggested that laser printers and other heavy loads be connected to the Bypass outlets. Xtreme Power Conversion Corporation Page 11...
When a Power Failure occurs, after turning on the UPS, and prior to the self-test sequence, the UPS will automati- cally shut down and not restart until utility power is restored. Check to assure power is available at the receptacle being used for input power. Xtreme Power Conversion Corporation Page 12...
Some computers are equipped with a special connector to link with the communication port. In addition, special cords may be required. Some computers may require special UPS monitoring software. Contact your dealer for the details on the various interface kits. Xtreme Power Conversion Corporation Page 13...
8. Measure the DC voltage of the approved replacement batteries for the proper value. 9. Install and connect new batteries ensuring proper polarity and voltage. 10. Replace cover(s), reconnect AC source, and restart the UPS. Xtreme Power Conversion Corporation Page 14...
UPS outlets of the UPS Contact Xtreme Power Conversion The battery is defective or worn out about replacement of batteries The on/off switch is designed to Turn the UPS off. Wait 10 sec &...
RS-232 bidirectional port, RS-232 to USB cable to enable USB connection, SNMP connectivity via external SNMP card/device INCLUDED IN BOX 6 ft USB-DB9 adaptor, 6ft DB9 cable, UPSMON, CD, phone cord, set vertical brackets, set horizontal brackets, user manual Xtreme Power Conversion Corporation Page 16...
4. (1) 6 ft USB-DB9 adaptor cable 5. (1) UPSMON CD (monitoring software) 6. (1) phone cord (for use with telephone/data surge protection) 7. (1) set of vertical mounting brackets 8. (1) set of horizontal mounting brackets Xtreme Power Conversion Corporation Page 17...
2. Verify there are no circuit breakers tripped. 3. Call your dealer for assistance. If you cannot reach your dealer, or if they cannot resolve the problem, call Xtreme Power Conversion Corp Technical Support at 800.582.4524. Technical support inquiries can also be made at support@xpcc.com.
Any technical advice furnished by XPC Corporation or a XPC Corpora- tion authorized representative before or after delivery with regard to the use or application of Xtreme Power Con- version equipment is furnished on the basis that it represents XPC Corporations best judgment under the situation and circumstances, but it is used at the recipient’s sole risk.
10. 10. Use dnpower for the User Name and for the Password. 11. 11. A Configuration Screen is displayed. Note: The default login user name and password are both dnpower. Configuration Screen When you enter into the Configuration Screen, the following menu is displayed: Xtreme Power Conversion Corporation Page 20...
Page 21
MIB-II System Group Setup Menu Current values for the following MIB-II OID: sysName: NETpower sysContact: admin sysLocation: 1) Set sysName 2) Set sysContact 3) Set sysLocation <0> Return to previous menu Enter Choice >> Xtreme Power Conversion Corporation Page 21...
Page 22
.NETpower SNMP agent adapter Configuration UPS Properties Setup UPS Identification Name: UPS UPS Attached Device: NA Last Battery Replacement Date: 12/31/1969 1) Set UPS Identification Name 2) Set UPS Attached Device 3) Set Last Battery Replacement Date Xtreme Power Conversion Corporation Page 22...
Page 23
You have to setup it correctly so that the .NETpower device can sent out mails when an event occurs. .NETpower SNMP agent adapter Configuration Email Parameter Setup SMTP Server IP Address: 1) Set SMTP IP Address <0> Return to previous menu Enter Choice >> Xtreme Power Conversion Corporation Page 23...
Page 24
0 to return to the previous menu without resetting the data. .NETpower SNMP agent adapter Configuration Restore default data ========================== 1) Yes, Do it <0> Return to previous menu Enter Choice >> Xtreme Power Conversion Corporation Page 24...
Page 25
.NETpower SNMP agent adapter Configuration Save & Exit ========================== 1) Yes, Do it <0> Return to previous menu Enter Choice >> Exit Without Saving Enter x at the main menu to exit the Configuration Screen Xtreme Power Conversion Corporation Page 25...
Need help?
Do you have a question about the 1000VA and is the answer not in the manual?
Questions and answers