Cleaning The Spa; Spa Repair; Lay-Z-Spa Storage; Disposal - Bestway Lay-Z-Spa 54113 Monaco Owner's Manual

Cleaning the spa

spa walls. Use soap and water to clean the walls and rinse thoroughly.
NOTE: DO NOT use hard brushes or abrasive cleaners.

Spa Repair

For Spa #54112 and inflatable cover #54113
If the spa is torn or punctured, use the provided heavy-duty repair
patch.
1. Dry the area to be repaired.
2. Remove the patch backing and place the patch over the
damaged area.
3. Smooth the surface to remove any air bubbles. A secure
unnoticeable repair can usually be made.
Lay- Z- Spa Storage
are completely dry. This is essential to extend the life of the spa.
We recommend using the pump to blow dry the spa, pump and
pipes. Re- attach the two stopper caps onto the spa's inlet and
outlet valves. It is recommended you store the spa in its original

Disposal

Meaning of crossed –out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities.Contact your local government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new
ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge.

TROUBLESHOOTING

problems whatsover, do not hesitate to contact Bestway or your authorized dealer. Here are some helpful tips to help you to diagnose
and rectify some common sources of trouble.
Problems
Pump does not operate
Pump not heating properly
Lay-Z-Massage System
does not work
Water Filtration not working
Pump adapters are not level
with the spa adapters
Spa leakage
Water not clean
Detergent residues and dissolved solids from bathing suits and chemicals may build up on the
Make sure the spa and pump
Bestway strives to provide the most trouble- free Spas on the market. If you experience any
Probable Causes
- Power failure
- Temperature set too low
- Dirty Filter Cartridge
- Improper water levels
- Forgot to remove the 2 Stopper Caps
- The thermal cut-out cut off
- Heating element failed
- Pump is too hot
- 30-minute auto shut off feature activated
- Something is wrong with the Pump
- Dirty Filter Cartridge
- One characteristic of PVC is that it
changes shape, which is normal
- Spa is torn or punctured
- Insufficient filtering time
- Dirty Filter Cartridge
- Improper water maintenance
For Spa #54113 (Not including inflatable cover)
If the spa is torn or punctured, use the provided PVC repair
patch and glue following these steps:
1. Clean and dry the damaged area.
2. Use the provided glue to coat both the damaged area and
PVC repair patch. Place the PVC repair patch over the
damaged area and smooth out any air bubbles.
3. Wait 24-hours before inflating. Check to ensure there is no
air leakage, if air is leaking re-apply the PVC repair patch.
package in a warm dry place.
NOTE: Plastic becomes brittle and susceptible to breaking
when exposed to subzero temperatures. Freezing can severely
damage the spa. Improper winterization of your spa can void
your warranty.
Solutions
- Check power source
- Set to a higher temperature
- Clean/replace the Filter Cartridge in time
- Add water to specified levels
- Remove the 2 Stopper Caps before heating
- Press the "Reset" button on the pump
- Call for service
- Unplug the Pump. After the Pump has cooled
insert the plug and press the Lay-ZMassage
System Button to activate
- Press the Lay-Z-Massage System Button to
reactivate
- Call for service if it does not reset
- Clean/replace the Filter Cartridge in time
- Elevate the pump with wood or another type of
insulated material to bring the pump's adapters
level with the spa's adapters.
- Use provided Heavy-duty Repair Patch or PVC
repair patch
- Increase filtration time
- Clean/replace the Filter Cartridge
- Refer to the chemical manufacturer's
instructions
10
S-S-001409