Display Diagnostic Codes; Cycle Count Since A Diagnostic Code - Maytag MAH8700AW* Service

Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing
requires power.
Selection Component
Rotary cycle
selector set to Bleach Valve
Colors. Press and Cold Water
Rotary Selector
Knob.
Press Rinse &
Spin switch pad

Display Diagnostic Codes

The diagnostic code display can be
toggled on and off from Service
Mode by pressing the Rinse&Spin
key and rotating the cycle select knob. The display will
show a "d". Rotating the Cycle Selector knob in either
direction will cycle through the list of codes one code
at a time with no wrap. Once an initial direction is
selected by the user (either Clockwise or
Counterclockwise), subsequent movements of the
knob in the same direction will show older codes. If
the user changes direction and turns the knob in the
opposite direction, the more recent code will be
displayed. If rotation is continued to the limits of the
list, the display will remain at the top or the end of the
list. A pair of dashes "- -" will be displayed at the end
of the list of codes, when the control reaches the top,
it will again show "d". A code generated during the
current cycle will be displayed with the Spin Indicator
LED turned "ON". If no cycle is currently running, a
code generated during the previous cycle will be
displayed with the Spin Indicator LED turned "ON".
Access Other Features While a diagnostic code is
displayed, if the Rotary Selector is pressed and held,
the machine will display the number of cycles since
the diagnostic code occurred. To clear the diagnostic
list press the Delay and Chime keys for 3 seconds
while viewing the list.
A code generated during the current cycle will be
displayed with the Spin Indicator LED turned "ON". If
no cycle is currently running, a code generated during
the previous cycle will be displayed with the Spin
Indicator LED turned "ON".

Cycle Count Since A Diagnostic Code

Occured/Clearing Diagnostic Codes
While a diagnostic code is displayed, if the Rotary
Selector is pressed and held, the machine will display
the number of cycles since the diagnostic code
occurred. To clear the diagnostic list press the Delay
and Chime keys for 3 seconds while viewing the list.
18
!
Function
st
1 press
Fabric
Softener fill.
nd
Valve 2 press
valves off
st
1 press
heater on. 2
Heater
press heater
off.
2
1
16026126 Rev. 0
WARNING
Diagnostic Codes
Diag. Description
Code
nd
1 No Drain
The door
fails to
2
unlock
3 No Fill
The door
4 fails to lock
5-7
Water level
8
sensor fault.
9
Unbalance
detected
during final
spin, which
10 prevented
the spinner
from
exceeding
400 rpm
Trigger Action to be
taken
The water
level fails to
drop below Displays "nd"
the Low Go to "Will Not
Water level
Drain"
reset within
Troubleshooting
15 minutes,
Section
before a spin
begins.
Door failed to
Displays "LO" Go to
unlock after "Will Not Unlock"
3attempts
Troubleshooting
Section
Continuous fill
Displays "nF"
of 12
Go to "No Water
minutes.
Fill"
Total fill of
Troubleshooting
14minutes.
Section
Door failed to Displays "FL" Go to
lock after 3 "Will not lock"
attempts Troubleshooting
Section.
Not Used
Input signal
from water
level Sensor
is out of Displays "LE"
range, Go to "No water fill
Washer will
Troubleshooting".
beep and
pause the
wash cycle.
Not Used
Never
LED – Will display
exceeded
"dc"
400rpm due
Go to "Wet Clothes
to an
"Troubleshooting
unbalance
Section"
load.
©2005 Maytag Services