Crestron, the Crestron logo, CresFiber, Crestron e-Control, Crestron Toolbox, DigitalMedia, DigitalMedia 8G, DM, DM 8G, and Excite are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby and Dolby Digital are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries.
Regulatory Compliance Regulatory Compliance As of the date of manufacture, the DM-RMC-200-S and DM-RMC-200-S2 have been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement Federal Communications Commission This device complies with part 15 of the FCC Rules.
Further Inquiries ......................31 Future Updates ......................32 Return and Warranty Policies ....................33 Merchandise Returns / Repair Service ..............33 Crestron Limited Warranty..................33 GNU General Public License ....................34 Contents i Operations & Installation Guide – DOC. 7246B...
7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. The manual is available from the Crestron Web site at www.crestron.com/dmresources.
Page 8
7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables sold separately.
Page 9
7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables sold separately.
0.23 inches (~6 mm) in diameter to extend from the electrical box as needed. An array of indicators is provided on the front of the DM receiver for easy setup and troubleshooting. 4 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
Applications The diagram below shows a DM-RMC-200-S in a standalone application. In this type of application, the DM-RMC-200-S is used with a DM 8G fiber transmitter such as the DM-TX-201-S (sold separately) and is not used with a DM switcher.
1920 x 1080 @ 60 Hz (1080p60) 1920 x 1200 @ 60 Hz plus any other resolution allowed by HDMI up to 165 MHz pixel clock (Continued on following page) 6 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
Page 13
DTS-ES, DTS 96/24, DTS-HD High Res, DTS-HD Master Audio™, up to 8ch PCM Analog Stereo 2-Channel Digital-to-Analog Conversion 24-bit 48 kHz (Continued on following page) DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 7 Operations & Installation Guide – DOC. 7246B...
Page 14
1.73 in (44 mm) with mounting bracket Weight 3.3 lb (1.5 kg) including bracket and power pack Included Accessory Universal 24 Volt DC Power Pack (Continued on following page) 8 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
Page 15
7. With reduced blanking only. 8. Using the DMTool in Crestron Toolbox, the amplifier can be enabled/disabled. 9. The latest software versions can be obtained from the Crestron Web site. Refer to the NOTE following these footnotes. 10. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product Catalog for a complete list of 2-Series control systems.
Page 20
Paralleled with rear panel AUDIO OUT connectors; Wire Size: Connector accepts 12 AWG maximum; Output Power: 15 watts per channel at 8 ohms (Continued on following page) 14 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
Page 21
USB HID (1) USB Type A female; USB 2.0 host port for connection of a mouse/keyboard or other USB HID-compliant device (Continued on following page) DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 15 Operations & Installation Guide – DOC. 7246B...
Page 22
7.5 miles (12 km) between devices, use Crestron CRESFIBER8G-SM or generic G.652.D (or better) single-mode fiber optic cable. Refer to the latest version of the Crestron DigitalMedia Design Guide (Doc. 4546) for complete system design guidelines. All wire and cables sold separately.
DM receiver is dropped directly into an Ethernet slot on the control system in SIMPL Windows without a DM switcher. The IP ID is set within the IP table of the DM receiver using Crestron Toolbox™. For information on setting an IP table, refer to the Crestron Toolbox help file. The IP IDs of multiple DM receivers in the same system must be unique.
Ensure that all excess wire is completely inside the electrical box and is not between the box and the DM receiver. 18 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
Page 25
3. Using the two included tie wraps (2013608), thread a tie wrap through the hole on the top and bottom of the holder, and then fasten the tie wraps to the power pack cable. DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 19 Operations & Installation Guide – DOC. 7246B...
Page 26
Power Pack #06-32 x 1” (2022484) (2007250) Installation of the power pack in the holder is shown below. Power Pack Installed in Holder of Mounting Bracket 20 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
From Power Pack Ethernet to Local (Included) Audio Output Line Level Network Device Audio Output DM IN SMF/LC: From DM Switcher, Transmitter, or Other DM Device DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 21 Operations & Installation Guide – DOC. 7246B...
Page 28
NOTE: For optimum performance, Crestron recommends using CresFiber 8G fiber optic cable for the DM-RMC-200-S and CresFiber 8G SM fiber optic cable for the DM-RMC-200-S2. NOTE: Fiber optic cable connectors and cable ends should be protected from contamination and scratching at all times.
Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron Web site. To post a question or to view questions submitted to Crestron’s True Blue Support, log in at www.crestron.com/onlinehelp. First-time users must establish a user account to fully benefit from all available features.
Page 30
In the first example, the DM-RMC-200-S is used with the DMCO-40 output card in a DM-MD8X8 switcher. In the second example, the DM-RMC-200-S is used with the C2ENET-2 card in an Ethernet slot on the control system. C2ENET-2 Device, Slot 8 (Using Output Card in a DM Switcher) C2ENET-2 Device, Slot 8 (Using Ethernet Slot on Control System) 2.
Page 31
IP ID of each unit. Refer to “Identity Code,” which starts on page 17. Program Manager Program Manager is the view where programmers “program” a Crestron control system by assigning signals to symbols. The symbol can be viewed by double-clicking the icon or dragging it into Detail View.
DigitalMedia Switchers Operations Guide (Doc. 6755). 2. Use the Device Discovery Tool in Crestron Toolbox to find the IP address of the DM receiver. The tool is available in Toolbox version 1.15.143 or later.
Page 33
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 3. Use the Address Book in Crestron Toolbox to create an entry for the DM receiver using the TCP connection type, and enter the IP address of the DM receiver. 4. Display the “System Info” window of the DM receiver (click the icon);...
Page 34
To establish TCP/IP communication between the PC and the DM receiver via the LAN port of the DM receiver: 1. Use the Device Discovery Tool in Crestron Toolbox to find the IP address of the DM receiver. The tool is available in Toolbox version 1.15.143 or later.
For details on upgrading, refer to the Crestron Toolbox help file. Check the Crestron Web site to find the latest firmware. (New users may be required to register to obtain access to certain areas of the site, including the FTP site.) To upgrade DM receiver firmware: 1.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. DM-RMC-200-S/DM-RMC-200-S2 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION PWR LED...
Crestron worldwide offices on the Crestron Web site (www.crestron.com/offices) for assistance within a particular geographic region. To post a question about Crestron products, log onto the Online Help section of the Crestron Web site (www.crestron.com/onlinehelp). First-time users must establish a user account to fully benefit from all available features.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Future Updates As Crestron improves functions, adds new features and extends the capabilities of the DM-RMC-200-S/DM-RMC-200-S2, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision.
(property or economic damages inclusive) arising from the sale or use of this equipment. Crestron is not liable for any claim made by a third party or made by the purchaser for a third party.
License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. 34 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
Page 41
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 35 Operations & Installation Guide – DOC. 7246B...
Page 42
THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 36 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC. 7246B...
Page 43
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 This page is intentionally left blank. DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 37 Operations & Installation Guide – DOC. 7246B...