1. Manuals
  2. Brands
  3. Paradyne Manuals
  4. Power Supply
  5. 9000 Series
  6. Installation instructions manual

Paradyne 9000 Series Installation Instructions Manual

Access carrier with dc power supply
Hide thumbs Also See for 9000 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
9000 Series Access Carrier
with DC Power Supply

Installation Instructions

Document Number 9000-A2-GN1K-10
September 2000
The 9000 Series Access Carrier with a DC power supply is a metal enclosure that
supports mounting of up to 14 Network Access Modules (NAMs). It has been designed
and approved for use in telephone company central offices only.
It can be mounted in either a 19-inch or 23-inch cabinet or rack. Up to six carriers can
be installed in one standard 72-inch cabinet. All LEDs (light-emitting diodes) on the
NAM(s) are visible from the front of the access carrier. All I/O cables on the I/O card(s)
are accessed from the rear.

Package Checklist

In addition to the access carrier, verify that your package also contains the following:
Power supply (already installed) and power cord
Fan tray for NAMs (already installed)
Baffle for heat deflection, including extender brackets for installation in a 23-inch
rack, and associated screws
Alarm Relay Connector
COM Port-to-PC cable
Set of five filler panels with screws for any unused NAM slots and I/O slots
— Two panels that cover four slots
— Two panels that cover two slots
— One panel that covers one slot
Brackets with screws for installing the housing in a cabinet or rack (already
mounted in the 19-inch rack position)
When your equipment arrives, inspect it for physical damage and tighten any screws
that may have worked loose. Contact your sales representative immediately if there are
any signs of shipping damage, or if anything is missing from your package. Otherwise,
proceed with the installation.
1

Advertisement

Table of Contents
loading

Related Manuals for Paradyne 9000 Series

Summary of Contents for Paradyne 9000 Series

  • Page 1: Installation Instructions

    Document Number 9000-A2-GN1K-10 September 2000 The 9000 Series Access Carrier with a DC power supply is a metal enclosure that supports mounting of up to 14 Network Access Modules (NAMs). It has been designed and approved for use in telephone company central offices only.

  • Page 2: Before You Begin

    Available Options The following options can be ordered separately: 72-inch EIA standard cabinet, 19 inches wide Redundant/replacement power supply Power supply fan tray Replacement fan tray for NAMs Replacement baffle FrameSaver SLV 9128 1-Slot Housing-to-Access Carrier Upgrade Instructions for converting a 1-slot FrameSaver SLV 9128 for use in the access carrier Contact your sales representative to order an option.
  • Page 3 HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control precautions to prevent damage to equipment. If you are not sure of the proper static control precautions, contact your nearest sales or service representative.
  • Page 4 Installing in a Cabinet/Rack with Threaded Screw Holes 1. Use a screwdriver to install the screw loosely enough to allow the bracket keyhole to drop under the screw head during installation. Use the 9th hole as shown on the left side of the carrier. Use the 12th hole on the right side of the carrier. Mounting Front Rail Bracket...

  • Page 5: Power Supply

    Installing in a Cabinet/Rack without Threaded Screw Holes 1. Slip a Speed Nut into the 3rd, 9th and 16th rail holes on the left side of the carrier, and into the 3rd, 12th and 16th holes on the right side of the carrier. Align the hole of the Speed Nuts with the hole in the rails.

  • Page 6: Alarm Relay Connector

    Installing a Redundant Power Supply The redundant DC power supply is a separately orderable product. Refer to the instructions that came with the power supply, DC Power Supply for 9000 Series Access Carrier Installation Instructions , Document No. 9000-A2-GN1L, for installation information.

  • Page 7: Installing The Baffle

    Once the carrier is connected to ac power, the fans in the fan tray begin circulating air and the green LED lights. If not, check potential reasons in Troubleshooting in the User’s Guide or Supplement. Installing the Baffle A baffle with Speed Nuts is provided for heat deflection. Extender brackets are also provided to convert the baffle for use in a 23-inch rack.

  • Page 8: Card Installation And Removal

    Card Installation and Removal NAMs are installed from the front of the access carrier. I/O cards that provide the interface connections for their associated NAMS are installed from the rear. NOTE: Cards can be added or removed without powering down the unit. I/O Card Installation The I/O card inserts into the rear of the access carrier and directly connects to the NAM that it supports.
  • Page 9 Installing Rear Filler Panels Once I/O card installations are completed, a filler panel must be installed for each unfilled I/O card slot to ensure compliance with safety requirements. WARNING: Filler panels must be installed on the unused slots to avoid possible injury from electrical shock.
  • Page 10 Installing Front Filler Panels Once card installations are completed, a filler panel must be installed for each unfilled NAM slot to ensure compliance with safety and FCC requirements. WARNING: You must install filler panels on the unused slots to avoid possible injury from electrical shock.
  • Page 11 THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS. CET APPAREIL NUMÉRIQUE DE LA CLASSE A RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATÉRIAL BROUILLER DU CANADA. Screw THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
  • Page 12 Power-On and Verification CAUTION: This product is intended to be used in a restricted access location. Grounding is provided by the DC grounding terminal on the rear of the housing. This is a safety feature. Equipment grounding is vital to ensure safe operation.

  • Page 13: Important Safety Instructions

    Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. All installation and service must be performed by qualified service personnel, as opening or removing covers may expose dangerous voltage points or other risks. 3.
  • Page 14 8. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. 9.
  • Page 15 The authority to operate this equipment is conditioned by the requirements that no modifications will be made to the equipment unless the changes or modifications are expressly approved by Paradyne. In order to maintain compliance with FCC limits, any supplied ferrite chokes must be installed in accordance with the card installation instructions.

  • Page 16: Warranty, Sales, Service, And Training Information

    Document Feedback We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the number and title of this document in your correspondence. Please include your name and phone number if you are willing to provide additional clarification.

Table of Contents