DSC Power 832 Installation Manual page 47

R E P O
Section Reporting Code
#
[344-348]
Openings
[348]
Auto-arm Cancellation
[348]
Special Opening
[349-350]
Battery Trouble/Restoral
[349-350]
AC Failure
Trouble/Resoral.
[349-350]
Bell Circuit
Trouble/Restpral
[349-350]
Fire Trouble/Restoral
[349-350]
Auxiliary Power
Trouble/Restoral
[349]
TLM Failure
[350]
TLM Restoral
[349-350]
General System
Trouble/Restoral
[349-350]
Gen System Supervisory
Trouble/Restoral
[351]
Line 1 or 2 FTC Restoral control panel has restored communications to
[351] Event Buffer is 75% Full
[351]
DLS Lead In
[351]
DLS Lead Out
[351]
General Zone
Trouble/Restoral
[351]
Delinquency
[352]
Periodic Test
[352]
System Test
[352]
LINKS Test
[353]
General Device Low
Battery Trouble/Restoral
[354]
User Walk Test Lead In
[354]
User Walk Test Lead Out User ends Walk Test [*][6][8]
* A/R = alarms/restorals; T/R = tamper/restorals; O/C = openings/closings; Maint. = maintenance;
Misc. = miscellaneous; Test = test transmission
** UU = user number (access codes 01-42); ZZ = zone number (01-32)
‡ Program the Contact ID "Fail to close" event code [(4)54] to report either closing or activity delinquency. Make sure your central station is aware of the
application of this reporting code.
R T I N
Code Sent When...
system disarmed (user 01-34, 40-42 indicated)
Auto-arm cancelled
Opening (disarming) using one of the following
methods: keyswitch, maintenance code, DLS
software, wireless key
Main panel battery is low/battery restored
AC power to control panel is disconnected or
interrupted/AC power restored (both codes
follow AC Failure transmission delay)
open/short circuit detected across bell
terminals/bell circuit restored
a trouble occurs/restores in a fire zone
Aux voltage supply trouble/restoral
telephone line monitoring trouble (sent via
LINKS. Do not program if LINKS not used)
Telephone line trouble restoral
"Service Required" trouble occurs (view
troubles using [*][2][3])/trouble restored
control panel loses/restores communications
with module(s) connected to the Keybus
central station on line 1 or 2
event buffer is almost full
downloading session start (initiated by panel)
downloading session complete
one or more zones have trouble/trouble
restored
programmed amount of time (days or hours) for
delinquency has expired without zone activity
or without system being armed
periodic sytem test transmission
[*][6] bell/communications test
LINKS test transmission
Wireless zones/pendants/handheld
keypads/wireless keys have low battery
User initiates Walk Test [*][6][8]
43
G V C O
Dialer
Direction*
O/C
O/C
O/C
Maint.
Maint.
Maint.
Maint.
Maint.
Maint.
Maint.
Maint.
Misc.
Misc.
Misc.
Misc.
Misc.
Misc.
Misc.
Test
Test
Test
Test
Test
Test
D E S
Auto- SIA Auto
matic Rep
Contact Codes**
ID
(4) A2 OP-UU
(4) A5 CE-00
(4) AA OP-00
(3) A2 YT-00/YR-00
(3) A1 AT-00/AR-00
(3) 21 UT-99/UJ-99
(3) 73 FT-00/FJ-00
(3) AA YP-00/YQ-00
(3) 51 LT-00
(3) 51 LR-00
(3) AA YX-00/YZ-00
(3) 33 ET-00/ER-00
(3) 54 YK-00
(6) 23 JL-00
(4) 11 RB-00
(4) 12 RS-00
(3) 72 UT-00/UJ-00
(4) 54 CD-00
(6) A2 RP-00
(6) A1 RX-00
(6) A3 TX-00
(3) 84 XT-00/XR-00
(6) A7 TS-00
(6) A7 TE-00