Table of Contents
Advertisement
Quick Links
USB 2.0 USB-2000
Thank you for purchasing the USB-2000. Please read this guide
thoroughly before installation.
FCC Radio Frequency Interference Statement Warning
The USB-2000 have been tested and found compliant with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when installed and
operated in a commercial environment. The USB-2000
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this user guide, may cause harmful interference
to radio communications. Operation of the USB-2000 in a residential area is likely
to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CE Statement
We, Icron Technologies Corporation, declare under our sole responsibility
that the USB-2000, to which this
declaration relates, are in conformity with European Standard EN 55022/A1
Class A, and EN 50082-1 (IEC 801-2, IEC 801-3, IEC 801-4)
IC Statement
These Class A digital apparatus complies with Canadian ICES-003.
©2006 Icron Technologies Corporation. All rights reserved. Icron
Technologies Corporation, the Icron Technologies Corporation logo, and the
Icron Technologies Corporation products referred to herein are either the
trademarks or the registered trademarks of Icron Technologies Corporation.
All other trademarks are property of their respective owners. Icron
Technologies Corporation assumes no responsibility for errors that may
appear in this manual. Information contained herein is subject to change
without notice.
Advertisement
Table of Contents
Related Manuals for Icron USB-2000
Summary of Contents for Icron USB-2000
- Page 1 FCC Radio Frequency Interference Statement Warning The USB-2000 have been tested and found compliant with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when installed and operated in a commercial environment.
-
Page 2: Table Of Contents
User Guide Contents Introduction....................1 USB-2000 Product Contents..............1 About the USB-2000.................. 2 Before You Begin ..................5 Installing the LEX unit................5 Installing the REX unit ................5 Connecting the LEX unit to the REX unit ..........5 Checking the Installation................6 Connecting a USB Device ................. - Page 3 USB-2000 Notes...
-
Page 4: Introduction
: Notes give additional information that could make installation NOTE easier. USB-2000 Product Contents When you open your USB-2000 for the first time you should find the following items: • USB-2000 User Guide • Local EXtender (LEX) unit. • Remote EXtender (REX) unit. -
Page 5: About The Usb-2000
With the USB-2000, utilizing singlemode fiber, USB devices can be located up to 10km from the host computer. The USB-2000 is composed of two individual units, the LEX unit and the REX unit. Note that there are no physical differences between the -2 and -4 units. - Page 6 User Guide The REX unit: USB-2000 The REX unit connects to a USB device using a conventional USB cable. The REX unit allows you to connect up to four USB devices. Additional devices may be connected by attaching a conventional USB hub to the REX unit.
- Page 7 USB Type B USB Type B port port connector connector Compatibility The USB-2000 complies with USB 2.0 specifications governing the design of USB devices. However, Icron Technologies Corporation does not guarantee that all USB devices are compatible with the USB-2000.
-
Page 8: Before You Begin
User Guide Before You Begin Before you can install the USB-2000, you need to prepare your site. 1. Determine where the host computer is to be located and set up the computer. 2. Determine where you want to locate the USB device(s). -
Page 9: Checking The Installation
Link port on the REX unit. 4. Plug the other end of the second patch cord into the fiber-optic information outlet near the USB device. : If you are installing a USB-2000 unit, the NOTE maximum length of the fiber-optic cable, including patch cords, must not exceed 500 meters. -
Page 10: Troubleshooting
The computer does not section of Device Manager, check that support USB hubs. the USB-2000 is recognised as a “Generic USB Hub”. d) The USB-2000 is malfunctioning. 6. If the USB-2000 is not recognised, contact technical support for assistance. - Page 11 USB 2.0 Ranger 442 and USB 2.0 Ranger 444 Symptoms/Cause Remedy A device is connected to the 1. Disconnect the USB-2000 from the REX unit and the computer. corresponding Device LED 2. Connect the USB device directly to the is off USB port on the computer.
-
Page 12: Specifications
Total system shipping 1.1 kg (2.4 lb) weight Temperature range 4°C to 40°C USB-2000 Link cable Two strands of 50/125µm MMF or 62.5/125µm (not included) MMF cabling are required. The cabling subsystem must provide a duplex connection with crossover, and must be terminated with Duplex... - Page 13 USB 2.0 Ranger 442 and USB 2.0 Ranger 444 USB-2000Link cable Two strands of 9/125µm SMF cabling are (not included) required. The cabling subsystem must provide a duplex connection with crossover, and must be terminated with Duplex LC connectors at both ends.
-
Page 14: Limited Hardware Warranty
Hardware Remedies Icron Technologies Corporation’s entire liability and the Licensee’s exclusive remedy for any breach of warranty, shall be, at Icron Technologies Corporation’s option, either (a) return of the price paid or (b) repair or replacement of hardware, which will be warranted for the remainder of the original warranty period or 30 days, whichever is longer.
Need help?
Do you have a question about the USB-2000 and is the answer not in the manual?
Questions and answers