Handle 14.8 [2.6] Due to continuous product development/improvement the specifications and configurations in this document are subject to change without prior notice. Manufactured by: NITTO KOHKI Co., Ltd. 2-9-4, Nakaikegami, Ohta-ku, Tokyo, 146-8555, Japan NITTO KOHKI CO.,LTD. Tel : (81)-3-3755-1111 Fax : (81)-3-3753-8791 E-mail : overseas@nitto-kohki.co.jp...
5. PREPARATION 6. HOW TO OPERATE THE TOOL 7. MAINTENANCE AND INSPECTION 8. OPTIONAL ACCESSORIES 9. ORDERING SERVICE PARTS 10. JET CHISEL (EJC-32A) 110V-120V 60Hz ASSEMBLY AND PARTS LIST 11. JET CHISEL (EJC-32A) 220V-240V 50Hz ASSEMBLY AND PARTS LIST PICTOGRAM Warning: It might be dangerous to operate the tool if the instructions supplied are not followed.
When an extension cable is used, check regularly and WARNING change it when it is damaged. The grip should be kept dry and clean. Maintain it so well IMPORTANT SAFETY INSTRUCTIONS FOR that it does not carry oil or grease. ALL ELECTRIC TOOLS (14) Switch off and take off the plug for the following: When using electric tools, basic safety precautions...
1 USAGE When performing maintenance, inspection, replacement or adjustment of parts, make sure to disconnect the attachment plug from the receptacle. This is an electric hand-held fast multiple needle scaler for scaling workpieces such as slags and spatters. Do not remove a rating plate. Please contact sales agent for replacement if they are taken off or damaged.
6 HOW TO OPERATE THE TOOL 7 MAINTENANCE AND INSPECTION WARNING WARNING Always wear eye protection. When performing maintenance, inspection, Everyday eyeglasses only have impact replacement or adjustment of parts, make sure resistant lenses. They do not protect eyes. to disconnect the attachment plug from the Also use face or dust mask, if operation receptacle.
Page 6
Take out a Fuse Holder which is packed with Sponge and replace it with a new one. e Replace it with a new Fuse which is specified by Nitto Kohki. The procedure is the opposite of the removal. Switch Handle (A)
t Press Switch Handle(A) into the Frame while you fit the Assembly q Insert the Brush Holder into the Frame with the chamfered Core Rods and complete the assembly. edge to the front. [Fig 16] y Tighten the Switch Handle fastening screws. Note: If it is difficult to get the lead wire terminal into the Brush Holder, insert the terminal a little obliquely.[Fig 13] [Fig 16]...
10 JET CHISEL (EJC-32A) 110V-120V~ ASSEMBLY AND PARTS LIST CAUTION The illustration is for information only. Users should never disassemble parts. Contact the sales agent from whom you purchased the tool or authorized dealer should the tool need service, repair or replacement of parts.
Page 9
The parts numbers with ( ) are included in the Ass'y parts written above them.(110V-120V~) No. Parts No. Parts Name Q'ty Price No. Parts No. Parts Name Q'ty Price TA99980 Anvil Guide Sub Ass'y 1set TP04234 Spring Washer M4 TP00045 Hex. Socket Cap Screw 8 TB02531 Stator Sub Ass'y 1set TQ03272 Rubber Plug...
11 JET CHISEL (EJC-32A) 220V-240V~ ASSEMBLY AND PARTS LIST CAUTION The illustration is for information only. Users should never disassemble parts. Contact the sales agent from whom you purchased the tool or authorized dealer should the tool need service, repair or replacement of parts.
Page 11
The parts numbers with ( ) are included in the Ass'y parts written above them.(220V-240V~) No. Parts No. Parts Name Q'ty Price No. Parts No. Parts Name Q'ty Price TA99980 Anvil Guide Sub Ass'y 1set TP04234 Spring Washer M4 TP00045 Hex. Socket Cap Screw 8 TB02533 Stator Sub Ass'y 1set TP16300 Spring 3.2...
Page 12
NITTO KOHKI CO.,LTD. Printed in JAPAN TQ12916-2...