Related Manuals for Intek MT-174XPS
Summary of Contents for Intek MT-174XPS
- Page 1 MT-174XPS 136-174 MHz VHF FM / 16CH / 5W PROFESSIONAL 2-WAY RADIO PC PROGRAMMABLE MT-460XPS 420-470 MHz UHF FM / 16CH / 4W PROFESSIONAL 2-WAY RADIO PC PROGRAMMABLE INSTRUCTION MANUAL...
- Page 2 User Information USER INFORMATION in accordance with art. 13 of the Legislative Decree of 25th July 2005, no. 15 ”Implementation of Directives 2002/95/EC, 2002/96/EC and 2003/108/EC, relative INSTRUCTION MANUAL to reduction of the use of hazardous substances in electrical and electronic equip- ment, in addition to waste disposal”.
- Page 3 “ General Population” in an uncontrolled the product certification and your right to use the product. INTEK S.R.L. declines any responsibility concerning any modification of the product, environment.
- Page 4 ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the American National Standards Institute (C95.1-1992), IEEE body when transmitting and only use the INTEK belt-clip which Standard for Safety Levels with Respect to Human Exposure to is listed in instructions when attaching the radio to your belt, etc., Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
- Page 5 FCC CAUTION: Changes or modifications to this device, not exp- head and body. ressly approved by INTEK, could void your authority to operate If you wear a portable two-way radio on your body, ensure that this transceiver under FCC regulations.
-
Page 6: Table Of Contents
Battery Pack 6.9.Transmission Begin and Transmission End Signals (PTT ID)...13 6.10.Lone worker / Emergency Alarm.........14 7.Wired Clone...................15 8.Trouble Shooting Guide..............15 9. Specifications / Optional Accessories...........17 Desk Charger Belt Clip Hand Strap Declaration of Conformity MT-174XPS..........18 Declaration of Conformity MT-460XPS..........19 User Information................20... -
Page 7: Preparation
Preparation 2.1 Charge the battery After being purchased or before the first charging after being laid Insert the cable of the power adaptor aside for a long time (2 months), the battery can reach its normal into the adaptor jack at the back of capacity after several times of charging, please ensure to charge the charger, insert the power adaptor the battery for at least once every three months. -
Page 8: Install The Antenna
2.4 Install external speaker/MIC Open the soft rubber cover of external speaker or MIC with your finger- Press the upper end of the battery -nail, insert the pin of matching external speaker or MIC into the pinhole down till the push button on the radio of the radio. -
Page 9: Basic Operation
. Channel: Turning to select channels 1-16. Turn the channel selector knob to select .Power/Volume knob the required channel. When the correct signal Turn clockwise to turn on the radio, keep turning to adjust the is received, you can hear sounds from the volume.To turn off the radio, just turn the knob anticlockwise till a speaker. -
Page 10: Auxiliary Functions
press again to resume normal operation. mode. Press to enable squelch and release to resume 14.Squelch off 3.Call Key 1 Sends the DTMF/2Tone code assigned to momentary normal operation. call 1 key. 15.Squelch off Hold this key to open the squelch. loosen this key 4.Call Key 2 Sends the DTMF/2Tone code assigned to to return to the normal operation. -
Page 11: Battery Saving
When changing the channel with the channel selector, after the cha- b)After the alarm, when the time of transmission exceeds the preset nnel is changed, the radio will announce the number of the channel time, the TOT timer will act. selected. -
Page 12: Scan
6.8 Scan status, it will transmit signals from the current channel, otherwise, The radio can be programmed to scan multiple channels to it will transmit signals from the channel where the scan is started. receive signals from them. Priority channel: The priority channel preset in the Scan list. 6.8.1 Start/End Scan Function Priority channel+ current channel: if the radio is at the Scan Staying a) Press the key programmed to “... -
Page 13: Lone Worker / Emergency Alarm
7. Wired Clone Mode If Transmission End has been set, when you release the PTT switch, If the wired clone function is enabled, the radio will not quit after the ID signals will be transmitted. entering the wired clone mode. To return to normal user mode, the If both have been set, the ID signals will be transmitted respectively user needs to restart the machine. -
Page 14: Specifications / Optional Accessories
9. SPECIFICATIONS B. The crystal X4 of phase lock loop is Frequency (MHz) VHF 136-174 MHz (MT-174XPS) broken. Please change it. UHF 420-470 MHz (MT-460XPS) C. The oscillator transistor is broken. Channel spacing 12.5 / 25 KHz Please change it. -
Page 15: Declaration Of Conformity Mt-174Xps
Declaration of Conformity MT-174XPS Declaration of Conformity MT-460XPS EC Certificate of Conformity EC Certificate of Conformity (to EC Directive 2006/95, 2004/108, 99/5) (to EC Directive 2006/95, 2004/108, 99/5) DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY With the present declaration, we certify that the following products :...
Need help?
Do you have a question about the MT-174XPS and is the answer not in the manual?
Questions and answers