Specifications - Toa Venas VM-2120 Cookbook

SPECIFICATIONS

Model No.
System Management Amplifier
Power Requirement AC: mains, 50/60 Hz
DC: 24 V DC/7.5 A, M3.5 screw terminal,
Barrier distance: 8 mm, Applicable
cable diameter: AWG22 – AWG14
Power Consumption With no signal present: 37 W
on AC Mains Under normal operating conditions
according to
EN60065: 1998 sec. 4.2: 107 W
With rated output signal: 201 W
Current Consumption With no signal present: 0.7 A
Under normal operating conditions
on 24V DC Power Input
according to
EN60065: 1998 sec. 4.2: 2.1 A
With rated output signal: 5.2 A
120 W
Rated Output
100 V/83 Ω, 70 V/42 Ω, 50 V/21 Ω
Output Voltage/Impedance
(selectable by the internal wiring change)
50 – 16,000 Hz
Frequency Response
Distortion Under 1%
Signal-to-Noise Ratio Over 60 dB
Bass: 100 Hz ±10 dB, Treble: 10 kHz ±10 dB
Tone Control
(Inputs 1 – 3 and BGM individually adjustable.)
Remote Microphone/ 2 RJ45 female connectors for connecting the RM-200M Remote Microphone and the VM-
Expansion Amplifier Connection 2120 or VM-2240 unit used as an expansion amplifier. Maximum distance: 800 m in total,
Link cable: Category 5 shielded Number of connectable RM-200M's: Up to 4
Twisted-Pair straight cable (TIA/EIA-568A standard)
1
Input Inputs 1 – 3: –60 dB* (MIC)/–10 dB*
connector (female)/phone jack
(Only Input 1 is additionally equipped with DIN connector*
Telephone paging input: Push-in terminal block*
terminal* 2
Control: No-voltage make contact input, open voltage: 30 V DC,
short-circuit current: under 0.1 A
1
BGM 1 - 2 –20 dB* , 10 kΩ, RCA pin jack, monaural (internally mixed)
1
Power amplifier input: 0 dB* , 10 kΩ, RCA pin jack
External speaker line input: 100 V line, for All-Zone Broadcast
(This input is selected when the "Unit's broadcast cutoff" control is activated.)
Output Speaker output: Plug-in screw connector*
5-zone selector with attenuator (all zones simultaneously selectable)
Direct speaker line output: Direct output from the power amplifier output transformer (attenuator bypassed),
Plug-in screw connector*
1
Line output 0 dB* , 10 kΩ, RCA pin jack
1
Recording output 0 dB* , 10 kΩ, RCA pin jack
1
Preamplifier output 0 dB* , 10 kΩ, RCA pin jack
For controlling Inputs 1 – 3, Push-in terminal block
Control Input
No-voltage make contact input, open voltage: 3.3 V DC, short-circuit current: under 1 mA
D-sub connector (25-pin, female)
Control Input and Output
Input: No-voltage make contact input, open voltage: 3.3 V DC,
short-circuit current: under 1 mA
Output: Open collector output, withstand voltage: 30 V DC, control current: under 10 mA
(1)External control input
•Activation of messages*
•Activation of power
•Activation and stop of Emergency Broadcast
•Unit's broadcast cutoff (when activated by an external emergency equipment)
(2)Status output
•Irregularity of communications with the Remote Microphone and an expansion amplifier
•AC power condition
•DC power condition
•Irregularity of the sound source of the Voice Announcement Board
•Failure (FAULT) indication on
•Power switch on
External Attenuator Plug-in screw connector*
withstand voltage: 30 V DC, 125 V AC, contact current: under 7 A (DC), under 7 A (AC)
Control Output
Surveillance Input D-sub connector (25-pin, female)
7 Input: No-voltage make contact input, open voltage: 3.3 V DC,
and Output*
short-circuit current: under 1 mA
Output: Open collector output, withstand voltage: 30 V DC,
control current: under 10 mA
24 V DC/0.1 A, for supplying power to an optional Amplifier
Power Supply
Control Unit RU-2001/2002, push-in terminal block*
Chime Tone Built-in chime: 2-tone chime/2-tone chime (fast repeat)/4-tone chime (Up)/
Voice Announcement Board sound source: Pre-recorded chime*
Function Two units stacking (VM-2120 or VM-2240)
Emergency broadcast (sequential control)
Broadcast priority control
Surveillance (failure detection) function*
Power supply to only one Remote Microphone (RM-200M)
Line resistance: Under 24 Ω (one way)
Operating Temperature 0°C to +40°C
Panel: ABS resin, dark gray, paint
Finish
Case: Steel plate, dark gray, paint
419 (W) ×143.3 (H) × 355.7 (D) mm
Dimensions
12.5 kg
Weight
Power cable (2m) ...1,
Accessory
Miniature type time-lag fuse...1,
Name label...1, Volume cover...4
Option Rack mounting bracket: MB-36, Input transformer: IT-450,
Voice announcement board: EV-200, Surveillance board: SV-200M
1
* 0 dB = 1 V
2
* Can be transformer-balanced with the addition of an optional IT-450 input transformer.
* 3 For connection of the Paging Microphone PM-660D with a remote control switch.
* 4 Usable cable diameter: AWG26 – AWG20, 0.5 mm 2 .
* 5 Usable cable diameter: AWG24 – AWG12, 2.5 mm 2 .
6
* An optional EV-200 Voice Announcement Board is required.
The chime sound source must be pre-recorded into a CF (CompactFlash) card to be inserted into the EV-200 Board.
* 7 An optional SV-200M Surveillance Board is required.
VM-2120 VM-2240
System Management Amplifier
AC: mains, 50/60 Hz
DC: 24 V DC/15 A, M3.5 screw terminal,
Barrier distance: 8 mm, Applicable
cable diameter: AWG22 – AWG14
With no signal present: 54 W
Under normal operating conditions
according to
EN60065: 1998 sec. 4.2: 255 W
With rated output signal: 549 W
With no signal present: 1 A
Under normal operating conditions
according to
EN60065: 1998 sec. 4.2: 5 A
With rated output signal: 14 A
240 W
100 V/42 Ω, 70 V/21 Ω, 50 V/10 Ω
(selectable by the internal wiring change)
(LINE) (changeable), 600 Ω, electronically balanced*
1
3
.)
4 1
Voice sound: –10 dB* , 10 kΩ, electronically-balanced input with shield
5
5
6
5
, relay, no-voltage make contact output, transfer type,
4
Single-tone chime/4-tone chime (Up & Down)/Gong/off
6
7
14.5 kg
Power cable (2 m) ...1,
Miniature type time-lag fuse...1,
Name label...1, Volume cover...4
Model No.
Power Requirement
Current Consumption
Distortion
Frequency Response
Signal-to-Noise Ratio
Audio Output
Microphone
Speaker Control
Emergency Broadcast
Voice Message Control
Volume Control
Connection Cable and Connector
Finish
Dimensions
Weight
Accessory
1
* 0 dB = 1 V
2
* Use the AC adapter AD-4800 optionally available as our service component.
3
* An optional EV-200 Board must be mounted in the VM-2120 or VM-2240 Amplifier.
2
, combined XLR
The voice messages must be pre-recorded into a CF (CompactFlash) card to be inserted into the EV-200 Board.
Model No.
Current Consumption
Connection
Function
Finish
Dimensions
Weight
Accessory
Model No.
Power Requirement
Power Consumption
Output
Frequency Response
Distortion
Memory Card
Playback Mode
No. of Playback Program
Operating Temperature
Operating Humidity
Dimensions
Weight
Accessory
1
* 0 dB = 1 V
2
* Trademark of SanDisk Corporation.
Note: Use the CompactFlash card adapter on the market for recording by the EV-350R.
Model No.
Power Requirement
Current Consumption
Control Input and Output
Failure Detection
Speaker Line Surveillance
Set Time
Operating Temperature
Operating Humidity
Weight
8
RM-200M
Remote Microphone
24 V DC (Operating range: 14 – 28 V DC)
Power input jack: Non-polarity type
2
Usable power input plug* : Outer diameter ø5.5 mm,
inner diameter ø2.1 mm, length 9.5 mm
100 mA maximum
Under 1%
100 – 20,000 Hz
Over 60 dB
, 600 Ω, balanced
1
0 dB*
Unidirectional electret condenser microphone
Zones 1 – 5 or Zones 1 – 10 (2 stacked amplifiers connection),
Groups 1 – 2, and All-Zone Broadcast
Activation of Emergency Broadcast (pre-recorded announcement*
or live microphone announcement) by Emergency Broadcast Switch
3
Activation of 5 messages*
Microphone volume control
Category 5 STP cable, RJ45 connector
ABS resin, bluish gray
190 (W) × 76.5 (H) × 215 (D) mm
(Gooseneck microphone excluded)
750 g
Link cable (3 m) ...1
RM-210
Remote Microphone Extension Unit
20 mA maximum (in terms of RM-200M's DC power input)
Connection to RM-200M by dedicated cable
Activation of Voice Announcement Board's voice messages
when controlling speakers in 10 zones at RM-200M
ABS resin, bluish gray
110 (W) × 76.5 (H) × 215 (D) mm
350 g
Extension cable ...1, Linkage bracket A...2,
Linkage bracket B...1, Screw for linkage bracket...12
EV-200
Voice Announcement Board
24 V DC, 0.1 A
3 W
1
0 dB*
20 – 20,000 Hz (44.1 kHz sampling)
20 – 14,000 Hz (32 kHz sampling)
Under 0.3% (44.1 kHz, recording method: Extremely High)
2 2
SanDisk* CompactFlash* card is optionally required.
Number of mountable card: 1
Single source playback
8 programs
0°C to +50°C
Less than 90% (must be free from dew condensation)
120 (W) × 18.6 (H) × 121 (D) mm
110 g
Mounting screw...2
SV-200M
Surveillance Board
24V DC
0.1 A
Input: No-voltage make contact input, open
voltage: 3.3 V DC, short circuit current: under 1 mA
(1) Speaker line initial setting activation signal
(2) Speaker line surveillance activation signal
Output: Open collector output, withstand
voltage: 30 V DC, control current: under 10 mA
(1) Monitoring short or open of individual
speaker line (zone 1 – 5)
(2) Ground fault (insulation resistance: under 50 kΩ)
(3) Power amplifier failures
Connector: D-sub connector (25-pin, female)
Power amplifier failure: 20 kHz pilot tone detection
Speaker line failure: 40 Hz impedance detection
Speaker lines are automatically monitored at set time intervals
(10 – 60 min, at 10 min intervals)
0°C to +50°C
Less than 90% (must be free from dew condition)
70 g
3