All-in-one console extender dual video, amplified or line-level audio, rs-232, and 3 separate usb extensions: two direct plus one with 4-port hub to 150 meters (500 ft) (20 pages)
HDMI, VGA/YPbPr, and Serial over Single Fiber TRADEMARKS USED IN THIS MANUAL Hall Research and its logo are trademarks of Hall Research. Any other trademarks mentioned in this manual are acknowledged as the property of the trademark owners. FEDERAL COMMUNICATIONS COMMISSION...
6.2 HR-733-S LCD Menu System ............9 6.3 LCD Menu Detailed Descriptions ..........13 6.4 More on RS-232 ................15 6.5 Using the HR-733-S in Command Mode ........16 6.6 RS-232 Control Commands ............17 7.0 Troubleshooting ................18 8.0 Specifications ..................18...
HDMI inputs, and provides separate R/L analog or SPDIF (TOSLINK) digital audio inputs for the VGA input. The HR-733 can also extend a bi-directional data channel (CEC, or RS- 232 Serial) over a single multi-mode (OM2 or OM3) fiber optic cable spanning distances of up to 1000m (3280ft).
Class 3R devices. This device is sensitive to Electrostatic Discharge (ESD). Prior to touching the unit (especially the connectors), touch a grounded object, and make sure the devices that will be plugged in to the HR-733 are properly grounded.
HDMI. Currently CEC is seldom used in pro-AV installations, and its implementation varies from one TV manufacturer to another, so as default the HR-733 uses the data lane for RS-232 communication and control. However, the CEC can be selected by the user, in which case the RS-232 port on the remote unit will not serve any function (the RS-232 port on the Sender can still be used for source selection).
The HR-733-R has l HDMI output and 1 bi-directional RS232 port. 5.3 Fiber Optic Cable Requirements Each end of the HR-733 uses a single SC connector and requires a multi- mode fiber-optic cable. Unlike some other fiber-optic equipment that may...
HDMI, VGA/YPbPr, and Serial over Single Fiber Data Rate (62.5/125 µm ) (50/125 µm ) (50/125 µm ) 1.65 Gb/s 250 m (820 ft) 500 m (1640 ft) 1000 m (3280 ft) (HDMI 1.2a) 3.4 Gb/s 150 m (500 ft) 250 m (820 ft) 500 m (1640 ft) (HDMI 1.3, 1.4)
Model HR-733 6.0 Operation The HR-733-S has 4 buttons and an LCD display on the front panel which allows users to easily navigate through the menu and change the settings. 6.1 Front Panel Buttons The 4 buttons are used to do the following tasks: ...
HDMI, VGA/YPbPr, and Serial over Single Fiber 6.2 HR-733-S LCD Menu System Screen toggles View Menu, Use HR-733 Extender every 3 seconds Figure 6 - Idle Menu (1.1) HDMI/DVI 1 SOURCE SELECT HDMI/DVI 2 HDMI/DVI 2 VGA/YPbPr VGA/YPbPr ADJUST (3.1)
Page 12
Model HR-733 VGA/YPbPr ADJUST (2.1) (2.11) Auto INPUT TYPE Auto YPbPr (2.2) OUTPUT (2.3) AUDIO Full Overscan (2.4) (2.4a) Underscan Letterbox SIZE Full Panscan (2.5) (2.5a) Standard PICTURE MODE Movie Movie Vivid User (2.6) (2.6a) CONTRAST Contrast: 43 (2.7) (2.7a)
Page 13
HDMI, VGA/YPbPr, and Serial over Single Fiber (2.2a) (2.2) Native 640x480 OUTPUT 1600x1200 800x600 1024x768 1024x800 1440x900 1280x1024 1400x1050 1600x1200 1680x1050 1920x1200 480i 480p 576i 576p 720p at 50 720p at 60 1080i at 50 1080i at 60 1080p at 50 1080p at 60 Figure 9 - VGA/YPbPr Output Resolution Menu (2.3)
Page 14
Model HR-733 (2.8) (2.8a) (2.8aa) FINE TUNE PHASE Phase: 61 (2.8b) (2.8ba) CLOCK Clock: 49 (2.8c) (2.8ca) H-POSITION H-Position: 50 (2.8da) (2.8d) V-Position: 98 V-POSITION Figure 11 - VGA/YPbPr Fine Tune Menu (2.9) COLOR (2.9b) (2.9c) (2.9a) GREEN BLUE (2.9aa) (2.9ba)
HDMI, VGA/YPbPr, and Serial over Single Fiber RS232 SETTINGS (4.1) (4.2) (4.3) RS232 BAUD RS232 PARITY RS232 FLOW CTRL CCTRL (4.3a) (4.2a) (4.1a) None None 19200 1200 None None 2400 4800 Even 9600 19200 38400 57600 115200 Figure 13 – RS-232 Settings Menu NOTE If there is no user activity for 1 minute, the idle menu will be shown and LCD backlight will be off.
Page 16
The output resolution setting can automatically match the native resolution of the display that the receiver HR-733-R is connected to, or may be specified by the user. (2.3) AUDIO – The audio source of VGA/YPbPr can be either a line level analog as L/R or optical digital as Optical.
(such as turning it on or off). Depending on the specification of the remote display, the baud rate of the remote unit can vary. Through the OSD menu of the HR-733 or the serial port in command...
HR-733-R remote unit. Most commands (such as input channel selection), can be issued to the HR-733-S regardless of how its data channel is configured (CEC or RS- 232 pass through). There are a few commands that cannot be executed in...
HDMI, VGA/YPbPr, and Serial over Single Fiber 6.6 RS-232 Control Commands All commands are prefixed with ==> All commands and responses are followed with a carriage return <CR> Wrong commands will get a response of ERR1 stands for input Source Channel where n=(0-3,?). (0 = Command: Blank, 1= HDMI#1, 2 = HDMI#2, 3 =VGA/YPbPr, ? = query input) Response:...
Cable Simplex (only 1 fiber) Multi-Mode. OM2 or OM3 Temperature Operating: 32 to 122°F (0 to 50°C); Storage: –40 to +185°F (–40 to +85°C) Enclosure HR-733-S: Steel, HR-733-R: Steel & Aluminum MTBF 90,000 hours (calculated estimate) Power 5V DC, 2.6A Size Sender: 1.66 H x 8.2 W x 7.826 D (4.2x20.8x19.8 cm)
Page 21
HDMI, VGA/YPbPr, and Serial over Single Fiber...