OPERATOR’S MANUAL MODEL ORDER # MODEL HD 2.0/10 Ed 1.575-400.0 HE-201006D HD 1.8/14 Ed 1.575-401.0 HE-201406D To locate your local Kärcher Commercial Pressure Washer Dealer nearest you, visit www.karchercommercial.us 9.800-088.0...
INTRODUCTION & IMPORTANT SAfETy INfORMATION Thank you for purchasing this Pressure Washer. DANGER: Improper connection of the equip- ment-grounding conductor can result in a risk We reserve the right to make changes at any time of electrocution. Check with a qualified electri- without incurring any obligation.
IMPORTANT SAfETy INfORMATION 14. Inlet water must be clean fresh water and no hotter WARNING: Grip cleaning wand WARNINg then 90°F. securely with both hands before starting. Failure to do this could 15. Manufacturer will not be liable for any changes result in injury from a whipping made to our standard machines or any components wand.
ASSEMbLy INSTRUCTIONS Nozzle Spray Wand Coupler Nozzle Safety Extension Spray gun/ Latch Wand High Pressure Hose STEP 1: Attach the high pressure STEP 2: Attach nozzle extension STEP 3: Pull the spring-loaded hose to the spray gun using teflon to spray gun/wand. Tighten both collar of the wand coupler back tape on hose threads.
OPERATINg INSTRUCTIONS Cold Water Source garden Hose STEP 1: Connect garden hose STEP 2: Trigger the spray gun to STEP 4: Connect to appropriate to the cold water source and turn eliminate trapped air then wait for a power supply. water on completely.
DETERgENTS AND gENERAL OPERATINg TECHNIqUES charging the warm water onto the ground. This thermal WARNING: Some detergents WARNINg device prevents internal damage to the pump. may be harmful if inhaled or in- gested, causing severe nausea, CLEANINg TIPS fainting or poisoning. The harm- ful elements may cause property Pre-rinse cleaning surface with fresh water.
SHUTTINg DOWN AND CLEAN-UP STEP 1: Remove deter- STEP 2: Turn off machine STEP 3: Turn off water STEP 4: Press trigger to gent suction tube from by flipping switch on rear supply. release water pressure. container and insert into of motor.
TROUbLESHOOTINg PRObLEM POSSIbLE CAUSE SOLUTION PUMP RUNNINg Check water supply and possibility of air seep- Pump sucking air NORMALLy bUT age. PRESSURE LOW ON Check valves sticking Check and clean or replace if necessary. INSTALLATION Unloader valve seat faulty Check and replace if necessary. Nozzle incorrectly sized Check and replace if necessary.
PREvENTATIvE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance.
AxD PUMP ExPLODED vIEW AxD PUMP ExPLODED vIEW PARTS LIST ITEM PART # DESCRIPTION kIT qTy ITEM PART # DESCRIPTION kIT qTy 89-30.0018.00 Cap, 1/8” 89-110-0407.00 O-Ring 89-3609.0156.00 Screw M8x55 89-110.0405.00 O-Ring 89-10.0045.00 Valve Kit 89-0009.005.00 Ring 89-110.0049.00 O-Ring, 1.78 x 1.4 A-D 89-110.0404.00 O-Ring 89-3009.019.00 Valve Seat 89-0009.004.00 Ring...
AxD PUMP ExPLODED vIEW PARTS LIST ITEM PART NO. DESCRIPTION kIT qTy 89-3410.030.00 Injector Body Kit Mx 1.5 89-3410.0303.00 Injector Body Kit 3/8 NPT 89-180.0197.00 Spring 89-409.0086.00 Check Valve 89-110.0397.00 O-Ring 89-409.0091.00 Check Valve Kit 89-0009.019.00 Ring 89-0009.030.00 Ring 89-141.0055.00 Piston Seal 150 Bar (50G, 300G, 35G) 89-141.0056.00 Piston Seal 180 Bar (305G)
LIMITED NEW PRODUCT Phone: 360-833-1600 WARRANTY—COMMERCIAL fax: 800-248-8409 PRESSURE WASHERS www.karchercommercial.us WHAT THIS WARRANTY COVERS All Kärcher commercial pressure washers are warranted by Kärcher to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below. This Limited Warranty, subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only.