Sony VPL-X2000U Service Manual page 67

The SERVICE MODE Menus
The SERVICE SETTING Menu
The SERVICE SETTING menu is for the settings to
be adjusted before operation.
S SERVICE SETTING INPUT-A
LENS CONTROL: O N
DIRECT POWER ON: O F F
ON DELAY: O F F
RS-232C/422A: 3 8 . 4 K
PJ COM: 3 8 . 4 K
Operation
1. Select an item
Use the V or v key to select the item, then press the b
or the ENTER key.
2. Change the setting
Press the V or v key to change the setting.
3. Restore the original screen
Press the B or the ENTER key.
The original screen is restored.
LENS CONTROL
When set to OFF, the SHIFT, FOCUS and ZOOM
keys on the Remote Commander and the control panel
do not function. To activate the keys, set to ON.
S SERVICE SETTING INPUT-A
LENS CONTROL: O N
DIRECT POWER ON: O F F
ON DELAY: O F F
RS-232C/422A: 3 8 . 4 K
PJ COM: 3 8 . 4 K
DIRECT POWER ON
Set to ON when you want to turn on the projector by
simply plugging in the AC power cord.
S SERVICE SETTING INPUT-A
LENS CONTROL: O N
DIRECT POWER ON: O F F
ON DELAY: O N
RS-232C/422A: 3 8 . 4 K
PJ COM: 3 8 . 4 K
60
(GB)
ON DELAY
When connecting multiple projectors, set to ON to turn
on the projectors sequentially one by one. The delay
time depends on the device index number on each
projector.
S SERVICE SETTING INPUT-A
LENS CONTROL: O N
DIRECT POWER ON: O F F
ON DELAY: O N
O F F
RS-232C/422A: O N 3 8 . 4 K
PJ COM: 3 8 . 4 K
RS-232C/422A
Sets the data transmission rate of the RS-232C/422A
connector.
S SERVICE SETTING INPUT-A
LENS CONTROL: O N
DIRECT POWER ON: O F F
ON DELAY: O F F
RS-232C/422A: 3 8 . 4 K
PJ COM: 3 8 . 4 K 1 9 . 2 K
9 6 0 0
Note
Set the same data transmission rate for all the
projectors and computers.
PJ COM
Sets the data transmission rate of the PJ COM
connector.
S SERVICE SETTING INPUT-A
LENS CONTROL: O N
DIRECT POWER ON: O F F
ON DELAY: O F F
RS-232C/422A: 3 8 . 4 K
PJ COM: 3 8 . 4 K 3 8 . 4 K
1 9 . 2 K
9 6 0 0
Note
Set the data transmission rate of all equipment
connected via the PJ COM connector to the same rate.
The W/B ADJUST Menu
The W/B ADJUST menu sets the values of the
COLOR TEMP in the PICTURE CTRL menu.
S W/B ADJUST INPUT-A
HIGH
LOW
SAVE TO MEMORY
Operation
1. Select the COLOR TEMP item to be set
Use the V or v key to select HIGH or LOW, then press
the b or ENTER key.
The projector enters into GAIN/BIAS adjustment
mode.
INPUT-A
HIGH
GAIN
R: 1 2 8
G: 1 2 8
B: 1 2 8
2. Select the item to be adjusted
Use the v key to select the item.
Each time the v key is pressed, the selected color item
appears in the following order.
R (GAIN) → G (GAIN) → B (GAIN)
↑ ↓
B (BIAS) ←G (BIAS) ← R (BIAS)
3. Adjust an item
To increase the number, press the b key.
To decrease the number, press the B key.
4. Restore the original screen
Press the ENTER key.
The original screen is restored.
To cancel the adjusted values
Turn off the projector. The saved data in the memory
will be retrieved when the projector is turned on again.
HIGH
Changes the color temperature of the COLOR TEMP's
HIGH setting value in the PICTURE CONTROL
menu.
INPUT-A
HIGH
GAIN
R: 1 2 8
G: 1 2 8
B: 1 2 8
LOW
Changes the color temperature of the COLOR TEMP's
LOW setting value in the PICTURE CONTROL
menu.
INPUT-A
LOW
GAIN
R: 1 2 8
G: 1 2 8
B: 1 2 8
SAVE TO MEMORY
Saves the settings of HIGH and LOW levels of
COLOR TEMP if you select SAVE TO MEMORY
with the V or v key and press the ENTER key.
S W/B ADJUST INPUT-A
HIGH
LOW
SAVE TO MEMORY
61
(GB)