Sony VPL-X2000U Service Manual page 44

Location and Function of Controls
Rear
6 5 4 3 2
INPUT C INPUT B
INPUT A VIDEO
IN
LIGHT +
R/R-Y Y
MUTING
G/Y C OUT
PCI AUDIO
8 8
B/B-Y INPUT SELECT
VIDEO VIDEO
SELECT VIDEO/
VIDEO
S VIDEO
SYNC
VIDEO VIDEO
/HD
INPUT A INPUT B INPUT C
AUDIO OUT
VD
POWER SAVING LAMP FAIL
(MONO) L L
AUDIO COVER FAIL 1
L (MONO)
IN
FAN FAIL
AUDIO
IN R R 3
HIGHT TEMP
R
REMOTE CONTROL S TRIG DEVICE INDEX
RS- RS- RS-232C/422A IN RS-485 OUT IN OUT
232C 422A
0
PLUG IN POWER
7 8 9 !º
1 Control panel
For details, see pages 12 (GB) and 13 (GB).
2 AUDIO OUT L/R jacks (phono type)
Connect to external active speakers.
The volume of the speakers can be controlled by the
VOLUME keys on the Remote Commander or the
control panel.
3 VIDEO connectors
Connect to external video equipment, such as a VCR.
Y IN/C IN (BNC type): Connect to the Y and C
video outputs of the video equipment.
S VIDEO IN (mini DIN 4-pin): Connects to the Y/C
video output of the video equipment.
S VIDEO OUT (mini DIN 4-pin): Used as loop-
through output via the Y/C IN connectors or the S
VIDEO IN connector.
VIDEO IN (BNC type): Connects to the composite
video output connector of the video equipment.
VIDEO OUT (BNC type): Used as loop-through
output of the VIDEO IN connector.
AUDIO IN L (MONO)/R jacks (phono type):
Connect to the audio output jacks of equipment,
such as a VCR. For stereo equipment, use both the
L and R jacks; for monaural equipment, use the L
(MONO) jack only.
14
(GB)
1
MENU
APA
+
RESET ENTER
VOLUME
– PATTERN ZOOM SHIFT FOCUS
2
4
0
!¡ !™
Note
If you have video equipment connected to both the Y/
C IN and S VIDEO IN connectors, the signal from the
Y/C IN connectors are selected prior to the S VIDEO
IN connector. When projecting video connected to the
S VIDEO IN connector, be sure not to connect any
cable to the Y/C IN connectors.
Note on the VPL-X2000E model
The optional IFB-X2000E interface board is required
for using the VIDEO connectors.
4 INPUT A connectors
RGB input connectors (R/R-Y/P , G/Y, B/B-Y/P
R
SYNC/HD, VD) (BNC type): Connect to the
video outputs of equipment such as a computer or
a video camera.
According to the connected equipment, the RGB
or component (R-Y, Y, B-Y) or HDTV (P , Y, P
R
signal is selected.
AUDIO IN L (MONO)/R jacks (phono type):
Connect to the audio output jacks of equipment
such as a computer or a video camera. For stereo
equipment, use both the L and R jacks; for
monaural equipment, use the L (MONO) jack
only.
Note
The INPUT A connectors do not function when the
PC-3000 signal interface switcher is connected.
5 Signal interface board attachment part
(INPUT B)
Optional signal interface board can be attached
according to your requirements. If you install the IFB-
12A interface board to this section and select the
output mode, you can output the signal input through
the INPUT A connectors.
For details on installing the interface boards, consult with
qualified Sony personnel.
6 Signal interface board attachment part
(INPUT C)
Optional signal interface board can be attached
according to your requirements.
Note
You cannot select the output mode when attaching the
IFB-12A interface board.
7 REMOTE connectors
Used to expand system capability.
RS-232C/RS-422A select switch: Selects according
to the interface connected to the RS-232C/RS-
422A connector.
RS-232C/RS-422A connector (D-sub 9-pin,
female): Connect to a computer to operate the
projector from the computer.
PJ COM IN/OUT connectors (D-sub 9-pin,
female): The connectors conform to the RS-485
standards and are used to expand system
capability for Sony projectors.
For details on connections, see the PJ COM protocol
manual for Sony projectors.
8 CONTROL S IN/OUT jacks (stereo minijack)
Connect to the control S jacks of other Sony
equipment.
,
B
CONTROL S IN/PLUG IN POWER (DC 5 V
output) jack: Connects to the CONTROL S OUT
jack of the supplied Remote Commander when
using as a wired Remote Commander. In this case,
you do not need to install the batteries in the
)
B
Remote Commander, since the power is supplied
from this jack.
CONTROL S OUT jack: Outputs the control S
signal.
Note
When connecting the remote commander cable to the
CONTROL S IN jack, the remote control detectors
will not function.
9 TRIG (trigger output) jack (monaural minijack)
The signal is transmitted from this jack to the
connected equipment whether the projector is on or
off. (This is not a power source for external
equipment.) When the power is on, the TRIG jack
transmits approximately 12 V trigger signal to external
equipment connected to the projector. This signal is
useful when you connect a system integrator, etc., to
the projector; you can pull down an electric screen,
draw an electric curtain, or dim lights at the same time
as you turn on the projector power. (You cannot use
the trigger signal as a power source.)
This jack outputs 0 V DC when the power is off.
!º DEVICE INDEX switch
Set the device index number of the projector when
using multiple projectors. You can set the numbers
between "01" and "99". It is set to "01" at the factory.
You can also set the group index number in the menu
for system setup.
Note
Do not set the device index number to "00". If you do,
the projector will be operated only with the keys on the
control panel.
!¡ AC IN socket
Connect the supplied AC Power cord.
!™ Lamp cover
15
(GB)