Table of Contents
Advertisement
The SET SETTING Menu
POWER SAVING
When set to ON, the projector goes into the power
saving mode and the lamp for light source turns off if
no signal is input for about 10 minutes.
The power saving mode is canceled when a signal is
input or any key is pressed.
SET SETTING
INPUT-A
STATUS:
ON
SPEAKER:
ON
LANGUAGE:
ENGLISH
INSTALLATION:
FLOOR-FRONT
OFF
POWER SAVING:
OFF
SIRCS RECEIVER:
ON
FRONT&REAR
GROUP INDEX:
0 1
DEVICE INDEX:
0 1
SIRCS RECEIVER
Selects the remote control detectors to be activated.
Change the setting if the wireless Remote Commander
does not work properly due to the influence of the
fluorescent lamp, etc.
SET SETTING
INPUT-A
STATUS:
ON
SPEAKER:
ON
LANGUAGE:
ENGLISH
INSTALLATION:
FLOOR-FRONT
OFF
POWER SAVING:
SIRCS
RECEIVER:FRONT&REAR
FRONT&REAR
GROUP INDEX:
FRONT
0 1
DEVICE INDEX:
REAR
0 1
OFF
FRONT & REAR: Activates both the front and rear
detectors.
FRONT: Activates the front detector only.
REAR: Activates the rear detector only.
OFF: Activates neither the front nor rear detector.
Note
When set to OFF, the wireless Remote Commander
does not function. Use the keys on the control panel or
the wired Remote Commander.
56
(GB)
GROUP INDEX
Groups multiple projectors or switchers to operate
them simultaneously.
GROUP INDEX: 0 1
You can set the group index number to the desired
number between 01 and 99.
DEVICE INDEX
Displays the index number set with the INDEX
switches on the rear of the projector. You cannot set
the device index number with this menu.
SET SETTING
INPUT-A
STATUS:
ON
SPEAKER:
ON
LANGUAGE:
ENGLISH
INSTALLATION:
FLOOR-FRONT
POWER SAVING:
OFF
SIRCS RECEIVER:
FRONT&REAR
GROUP INDEX: 0 1
DEVICE INDEX:
0 1
For details for setting the number, see page 45 (GB).
The SIGNAL SELECT Menu
The SIGNAL SELECT Menu is used for selecting the
input signal.
Depending on the interface board installed in the
projector, some items may not be displayed in the
menu.
SIGNAL SELECT
INPUT-A
INPUT-A:
RGB
INPUT-B:
RGB
INPUT-C:
RGB
Operation
Use the V or v key to select the input, then press the
ENTER key.
INPUT-A
Selects audio and video signals input from the INPUT
A connectors. You can select the RGB, component or
HDTV (YP
P
) signal.
B
R
SIGNAL SELECT
INPUT-A
INPUT-A:
RGB
RGB
INPUT-B:
COMPONENT
RGB
INPUT-C:
RGB
YP
P
B
R
Note
When the PC-3000 signal interface switcher is
connected to the INPUT A connectors, you cannot
select the item.
INPUT-B
Selects the input signal from the connectors on the
optional IFB-12A interface board installed in the
INPUT B section. You can select the RGB,
component, HDTV (YP
P
), video or S video signal.
B
R
SIGNAL SELECT
INPUT-B
INPUT-A:
RGB
INPUT-B:
RGB
RGB
INPUT-C:
RGB
COMPONENT
VIDEO
S-VIDEO
YP
P
B
R
Note
This item is not displayed when the optional interface
board other than the IFB-12A is installed in the INPUT
B section, or when the output mode is selected on the
IFB-12A.
INPUT-C
Selects the input signal from the connectors on the
optional IFB-12A interface board installed in the
INPUT C section. You can select the RGB,
component, HDTV (YP
P
), video or S video signal.
B
R
SIGNAL SELECT
INPUT-C
INPUT-A:
RGB
INPUT-B:
RGB
INPUT-C:
RGB
RGB
COMPONENT
VIDEO
S-VIDEO
YP
P
B
R
Note
This item is not displayed when the optional interface
board other than the IFB-12A is installed in the INPUT
C section.
57
(GB)
Advertisement
Table of Contents
Troubleshooting
