Quick Setup Guide Start Here MFC-J4510DW Please read the Product Safety Guide first before you set up your machine. Then, please read this Quick Setup Guide for the correct setup and installation. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death WARNING or serious injuries.
Fan the stack of paper well to avoid paper jams Load plain A4 paper and misfeeds. NOTE Always make sure that the paper is not curled or CAUTION wrinkled. DO NOT carry the machine by holding the scanner Gently put the paper into the paper tray print cover or the Jam Clear Cover.
While holding the paper tray in place, pull out Connect the power cord the paper support until it clicks, and then unfold the paper support flap. and telephone line NOTE WARNING For printing and copying on special media, open the manual feed slot a on the back of the •...
Lift the scanner cover until it locks securely into Lift the scanner cover to release the lock a. the open position. Gently push the scanner cover support down b and close the scanner cover c using both hands. Connect the telephone line cord. Connect one end of the telephone line cord to the socket of the machine marked LINE.
Unpack the ink cartridge. Install the ink cartridges Turn the green release lever on the orange protective packing a counterclockwise until it clicks to release the vacuum seal. Then remove the orange protective packing a as shown. CAUTION If ink gets in your eyes, wash it out with water at once and call a doctor if you are concerned.
Check the print quality Choose a Receive Mode There are four possible receive modes: Fax Only, When the preparation process has finished, the Fax/Tel, Manual and External TAD. Touchscreen shows Set paper and press [OK]. Do you want to use the telephone features of your Press OK.
Set the date and time Set Tone or Pulse dialling mode Press Press Press All Settings. 00:00 01.01.2012 Press (Date and Swipe up or down, or press a or b to display Time). Initial Setup. Press Initial Setup. Press Date. Press Tone/Pulse.
Set the telephone line compatibility (VoIP) If you are connecting the machine to a VoIP service (over the Internet) you need to change the compatibility setting. NOTE If you are using an analogue telephone line you can skip this step. Press Press All Settings.
• If your computer does not have a CD-ROM drive you can download the latest drivers, manuals and utilities for your model from the Brother Solutions Center at http://solutions.brother.com/. Some software applications included on the CD-ROM may not be available as a download.
® Windows For USB interface users ® ® ® (Windows XP Home/XP Professional/Windows Vista /Windows Before you install Connect the USB cable Make sure that your computer is ON and you are logged on with Administrator rights. Install MFL-Pro Suite Put the supplied installation CD-ROM into your CD-ROM drive.
The following screens will appear. • When the Software Update Setting screen appears, choose the software update setting you want and click OK. • When the Brother Product Research and Support Program screen appears, select IMPORTANT your preference and follow the on-screen instructions.
Macintosh For USB interface users (Mac OS X v10.5.8, 10.6.x, 10.7.x) Before you install Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. Connect the USB cable IMPORTANT IMPORTANT Make sure that the cable does not restrict the...
Next. Follow the on-screen instructions. Please wait for the software to install. After the installation, the Brother software will search for the Brother device. This will take a few moments to complete. Choose your machine from the list, and then click OK.
Wired Network ® Windows For wired network interface users ® ® ® (Windows XP Home/XP Professional/Windows Vista /Windows Before you install Make sure that your computer is ON and you are logged on with Administrator rights. Connect the network cable IMPORTANT Make sure that the cable does not restrict the cover from closing, or an error may occur.
Follow the appears, choose the software update setting on-screen instructions. you want and click OK. • When the Brother Product Research and Choose Wired Network Connection Support Program screen appears, select (Ethernet), and then click Next.
Wired Network Macintosh For wired network interface users (Mac OS X v10.5.8, 10.6.x, 10.7.x) Before you install Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. Connect the network cable...
Please wait for the software to install. After the installation, the Brother software will search for the Brother device. This will take a few moments to complete. If the machine is configured for your network, choose your machine from the list, and then click OK.
For Wireless Network Users For wireless network interface users Before you begin Although your Brother machine can be used in both a wired and wireless network, only one of the connection methods can be used at a time. NOTE If you have previously configured the wireless settings of the machine you must reset the network settings before you can configure the wireless settings again.
For Wireless Network Users SSID (Network Name) / Network Key Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings. Item Record the current wireless network settings...
For Wireless Network Users Setup using the Temporarily connect the USB cable (not included) directly to the computer and the installation CD-ROM and machine. ® a USB cable (Windows If the confirmation screen appears, check the box and click Next, go to g. &...
For Wireless Network Users Enter the Network Key you wrote down on page 19, and then click Next. NOTE If your network is not configured for Authentication and Encryption, the following screen will appear. To continue configuration, click OK and go to j. Click Next.
For Wireless Network Users Manual setup from the Enter the Network Key you wrote down in step 17-b on page 19 using the Touchscreen. control panel using the Setup Wizard (Macintosh, Press to cycle between lower case and mobile devices and upper case.
Put the supplied installation CD-ROM into your sensitive. CD-ROM drive. Follow the on-screen instructions. The installation of the Brother drivers will automatically start. The installation screens The CD-ROM Top menu will appear. appear one after another. Click Install MFL-Pro Suite and click Yes if you accept the license agreements.
The following screens will appear. • When the Software Update Setting screen appears, choose the software update setting you want and click OK. • When the Brother Product Research and Support Program screen appears, select your preference and follow the on-screen instructions.
If your wireless settings fail, the Wireless Device Setup Wizard screen appears. Follow the on-screen instructions to complete the wireless configuration. Choose your machine from the list, and then click OK. The installation of the Brother drivers will automatically start. Please wait for the software to install.
Install Optional Applications ® Windows Install optional Install FaceFilter Studio applications Help You can install the following applications. To run FaceFilter Studio, go to FaceFilter Studio and BookScan & Start/All Programs/Reallusion/ Whiteboard Suite supported by FaceFilter Studio on your computer. Reallusion, Inc Click Check for Updates on the screen.
For Network Users Reset the network settings to factory default To restore all network settings of the internal Print/Scan server to the factory default, please follow the steps below. Make sure the machine is not operating, then disconnect all the cables from the machine (except the power cord).
The contents of this manual and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication.