Jet JBOS-5 Operating Instructions And Parts Manual

Jet JBOS-5 Operating Instructions And Parts Manual

Benchtop oscillating spindle sander
Hide thumbs Also See for JBOS-5:

Advertisement

This .pdf document is bookmarked
Operating Instructions and Parts Manual
Benchtop Oscillating Spindle Sander
Model JBOS-5
For models with serial no. 11095097 and higher
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Part No. M-708404
Ph.: 800-274-6848
Revision C1 06/2013
www.waltermeier.com
Copyright © 2013 Walter Meier (Manufacturing) Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JBOS-5 and is the answer not in the manual?

Questions and answers

Summary of Contents for Jet JBOS-5

  • Page 1 This .pdf document is bookmarked Operating Instructions and Parts Manual Benchtop Oscillating Spindle Sander Model JBOS-5 For models with serial no. 11095097 and higher WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708404 Ph.: 800-274-6848 Revision C1 06/2013 www.waltermeier.com...
  • Page 2: Warranty And Service

    Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local Walter Meier distributor, or visit waltermeier.com. WARRANTY JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW = Woodworking). WHAT IS COVERED? This warranty covers any defects in workmanship or materials subject to the exceptions stated below.
  • Page 3: Table Of Contents

    Insert Plate Diameters ............................9   Optional Accessories (purchased separately) ..................... 10   Replacement Parts .............................. 10   Table Assembly for the JBOS-5 ........................11   Base and Motor Assembly for the JBOS-5 ...................... 12   Parts List for the JBOS-5 ..........................13...
  • Page 4: Warning

    Warning 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this tool until proper training and knowledge have been obtained. 2. Keep guards in place and in working order. 3. Keep fingers and hands away from the spindle while in operation. Avoid getting fingers too close to the drum.
  • Page 5: Introduction

    This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a JET Model JBOS-5 Oscillating Spindle Sander. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.
  • Page 6: Unpacking And Setup

    Unpacking and Setup Contents of the Shipping Container (see Figure 1) Spindle Sander Spindle Storage Plate (pre-installed) Insert Storage Plate (pre-installed) Round Opening Inserts (3/4” and 2”) Oblong Opening Inserts (3/4” and 2”) Sanding Spindles & Sleeves: Figure 1 1/4”x6”; 1/2”x6”; 5/8”x6”; Contents of Shipping Container 1-1/2”x5-1/2”;...
  • Page 7: Insert Plates

    Dust Collection The dust port (B, Figure 5) can be hooked directly to a 2” hose for dust collection. See your local JET distributor for the complete line of dust collectors, as well as Hoses and Accessories. Customize your installation and obtain maximum performance with JET dust hoods, hoses, clamps, fittings, and blast gates.
  • Page 8: Turning The Sander On & Off

    Turning the Sander On & Off Note: Before hooking the sander to the power source, make sure the switch is in off position. The sander can be turned on by flipping the switch to the on position. There is a removable key in the tip of the switch that can be removed in the off position.
  • Page 9: Insert Plate Diameters

    Insert Plate Diameters This will assist you in determining which spindle diameters will work in each insert plate.
  • Page 10: Optional Accessories (Purchased Separately)

    Optional Accessories (purchased separately) 709534 ..3” Dia. Spindle Assembly 6286984 ..Table Insert for 3” Spindle Sanding Sleeves (4 per pack): Stock No. Diameter (in.) Length (in.) Grit 575891 575893 575894 575901 575903 575904 575906 575908 575909 575921 1-1/2 5-1/2 575923 1-1/2...
  • Page 11: Table Assembly For The Jbos-5

    Table Assembly for the JBOS-5...
  • Page 12: Base And Motor Assembly For The Jbos-5

    Base and Motor Assembly for the JBOS-5...
  • Page 13: Parts List For The Jbos-5

    53 ....JBOS5-53....Support Trunnion-Right ................. 1 54 ....JBOS5-54....Support Trunnion-Left ..................1 55 ....JBOS5-55....JET Lock Knob ............M6x15 ......2 56 ....JBOS5-56....Hex Socket Cap Screw ..........M5x15 ......6 57 ....6286492 ....Set Screw ..............M6x5 ......1 58 ....
  • Page 14 ....6286982 ....Round Table Insert (for 1/4" to 1” spindles),not shown ........1 92 ....JBOS5-92....Oil Cap ......................1 93 ....JBOS5-93....JET Label....................... 1 94 ....JBOS5-94....Warning Label....................1 95 ....JBOS5-95....I.D Label ......................1 96 ....
  • Page 16 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com www.waltermeier.com...

Table of Contents