Related Manuals for Jet JAT-730 505730
Summary of Contents for Jet JAT-730 505730
- Page 1 Pneumatic RO Palm Sander #505730, JAT-730 #505731, JAT-731 Operation & Parts Manual M-505730 Edition 2 06/2015 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
-
Page 2: Warranty And Service
Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
10. The air tool must be properly lubricated before operating. Do not use this tool for other than its intended use. If used for other purposes, JET disclaims 11. Never start a percussion type air tool (chipper, any real or implied warranty and holds itself breaker, buster, etc.) without securing the... - Page 4 33. Do not lubricate the tool with combustible or storing tool. liquids, such as kerosene, diesel or jet fuel. 23. Make sure tool is switched off, and your finger 34. Do not dispose of this tool with normal off the trigger, before connecting to air supply.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
Any missing parts or damage should be reported Grip tool with fingers and palm, pressing ® immediately to your JET distributor. Do not use a down on throttle lever. Allow it to come to full damaged tool. Read this instruction manual speed before placing it on workpiece. - Page 8 Tool Pressure Make sure air compressor supplies clean, dry air at correct CFM for the tool. JET Air Tools operate on 70-to-100 psi (pounds Set air pressure to 90 psi. per square inch) air pressure measured at the tool when the tool is operating. Set tool to 90 psi unless indicated otherwise.
- Page 9 Lubrication Use a light oil containing rust inhibitors, such as SAE #10. Many JET air tools have integral oil reservoirs, which should be kept filled when in-line oilers are not used. If greasing is required, use a grease that is highly water resistant for front case components on air impact wrenches, grinders and sanders.
- Page 10 Troubleshooting JAT-730/731 RO Palm Sander Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 11: Replacement Parts
Replacement parts Replacements are listed on the following pages. To order parts or reach our service department, call 1-800- 274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately. ... - Page 12 #505730, JAT-730, RO 5in. Palm Sander – exploded view JAT-730,731 Random Orbit Palm Sander ...
- Page 13 #505730, JAT-730, RO 5in. Palm Sander – parts list Index Part No. Description Index Part No. Description JAT730-01 Housing JAT730-23 O-Ring 5x2 JAT730-02 Spring pin 3x40L JAT730-24 Lock ring JAT730-03 Air inlet JAT730-25 Grip hat JAT730-04 Throttle lever JAT730-26 Shroud JAT730-05 Throttle valve JAT730-27 Ball bearing 6001ZZ JAT730-06 Bushing...
- Page 14 #505731, JAT-731, RO 6in. Palm Sander – exploded view JAT-730,731 Random Orbit Palm Sander ...
- Page 15 #505731, JAT-731, RO 6in. Palm Sander – parts list Index Part No. Description Index Part No. Description JAT730-01 Housing JAT730-23 O-Ring 5x2 JAT730-02 Spring pin 3x40L JAT730-24 Lock ring JAT730-03 Air inlet JAT730-25 Grip hat JAT730-04 Throttle lever JAT730-26 Shroud JAT730-05 Shaft JAT730-27 Ball bearing 6001ZZ JAT730-06 Bushing...
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-730,731 Random Orbit Palm Sander ...