Selecting The Analog Or Digital Input Mode - JVC RX-8010VBK Service Manual

Selecting the Analog or Digital Input
Mode
When you have connected digital source components using the
digital terminals (see page 8), you need to change the input mode for
these components to the appropriate digital input mode correctly —
DGTL AUTO, DGTL DTS, or DGTL D.D.
Before you start, remember...
• The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital
input mode for. Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to
digital input even if you follow the procedure below.
On the front panel:
1. Press one of the source selecting button (DVD, TV
SOUND/DBS, CD, CDR, or TAPE/MD)* for which
you want to change the input mode.
The lamp on the front panel button for selected source lights up.
DVD MULTI DVD
VCR 1
PHONO CD CDR
SOURCE NAME
Note:
* Among the source listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See "Digital Input (DIGITAL IN) Terminal Setting"
on page 19.)
2. Press INPUT ANALOG/DIGITAL
(INPUT ATT) briefly to change
the input mode.
• Each time you press the button, the input
mode changes as follows.
DGTL AUTO
(Digital)
DGTL AUTO: Select this for the digital input mode. The
receiver automatically detects the incoming
signal.
ANALOG: Select this for the analog input mode.
ANALOG
When selecting "DGTL AUTO," following indicators showing
detected signals light up on the display.
: Always lights up.
: • Lights up when Linear PCM signals come in.
LINEAR PCM
• The frame flashes when detecting signals.
• LINEAR PCM without frame flashes when
PCM signals are not recognized.
DIGITAL
: Lights up when Dolby Digital signals come in.
: Lights up when DTS Digital Surround signals
come in.
VCR 2 VIDEO TV SOUND/DBS
SOURCE NAME
TAPE / MD USB AUDIO FM / AM
INPUT
ANALOG/DIGITAL
INPUT ATT
ANALOG
always lights up.
When playing a software encoded with the Dolby Digital or
DTS Digital Surround, "DGTL AUTO" may not work properly
and the following symptoms may occur:
• Sound does not come out at the beginning of playback.
• Noise comes out while using the searching or skipping
chapters or tracks.
In this case press CONTROL UP 5/
DOWN ∞ to select "DGTL D.D" or "DGTL
DTS" while "DGTL AUTO" still remains
on the display.
• Each time you press the button, the input
mode changes as follows.
DGTL AUTO
(Digital)
DGTL DTS
(Digital)
When selecting "DGTL D.D" or "DGTL DTS," following
indicators showing detected signals light up on the display.
: Always lights up.
When selecting "DGTL D.D"
DIGITAL : • Lights up when Dolby Digital signals come in.
• The frame flashes when Dolby Digital signals
are not recognized.
When selecting "DGTL DTS"
: • Lights up when DTS Digital Surround signals come in.
• The frame flashes when DTS Digital Surround
signals are not recognized.
Note:
When you turn off the power or select another source, "DGTL
D.D" and "DGTL DTS" settings are canceled and the digital input
mode is automatically reset to "DGTL AUTO."
To change the input mode back to analog input, select
"ANALOG" in step 2.
From the remote control:
1. Press the source selecting
button (DVD, CD, TV/DBS,
CDR, or TAPE/MD)* for
which you want to change
the input mode.
Note:
* Among the source listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See "Digital Input (DIGITAL IN) Terminal Setting"
on page 19.)
2. Press ANALOG/DIGITAL INPUT
to change the input mode.
• Each time you press the button, the
input mode changes as follows:
DGTL AUTO
(Digital)
When playing a software encoded with the Dolby Digital or
DTS Digital Surround, "DGTL AUTO" may not happen to
work well. In this case press CONTROL UP 5/DOWN ∞ on
the front panel to select "DGTL D.D" or "DGTL DTS" (while
"DGTL AUTO" remains on the display).
Note:
You can select "DGTL D.D" or "DGTL DTS" from the remote control by
using the On-Screen Menus (see page 36).
CONTROL
DOWN UP
DGTL D.D
(Digital Dolby Digital)
DVD DVD MUILTI CD
TV/DBS VIDEO CDR
VCR 1 VCR 2 TAPE/MD
ANALOG/DIGITAL
INPUT
ANALOG
FM/AM
PHONO
USB
20