Vivotek FD8363 Quick Installation Manual
  1. Manuals
  2. Brands
  3. Vivotek Manuals
  4. Security Camera
  5. Supreme FD8363
  6. Quick installation manual
Vivotek FD8363 Quick Installation Manual

Vivotek FD8363 Quick Installation Manual

Fixed dome network camera
Hide thumbs Also See for FD8363:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual

Advertisement

Table of Contents
loading

Related Manuals for Vivotek FD8363

Summary of Contents for Vivotek FD8363

  • Page 2: Package Contents

    Do not insert sharp or tiny objects Do not drop the Network Camera. into the Network Camera. Package Contents FD8363 Mounting Plate Alignment Sticker / L-type Hex Key Wrench / Dessicant Ceiling Hole Template Sticker Bag / DC Connector / Screws / Hex...

  • Page 3: Inner View

    Physical Description Remove the foam pad Inner View Vari-focal Lens IR LEDs (8 units, effective up to 15m) Black Cover Tilt Adjustment Screw Auto Focus Button Micro SD/SDHC/SDXC Card Slot Reset Button Jumpers Microphone Video Output NTSC Internal 60Hz Audio/Video Out (green) External 50Hz...

  • Page 4: Hardware Installation

    Record the MAC address under the camera base before installing the camera. Replace the side opening cover with the included side outlet bushing if you want to route cables from the side of camera. The 1/2" protection conduits and tubing are separately purchased. Hardware Installation First, use the included T20 hex key wrench to loosen the four screws and detach the dome cover from the camera base.

  • Page 5: Cabling Assembly

    Cabling Assembly Connect power lines and if you have external devices such as sensors and alarms, make the connection from the general I/O terminal block. Pin Definitions Top View DC 12V- DC 12V+ AC24V_2 AC24V_1 DI- (GND) DO+ (+12V) Power and IO cables pass through a waterproof connector. The Ethernet cable should be routed through a rubber seal plug.

  • Page 6: Connecting Rj45 Ethernet Cable

    Connecting RJ45 Ethernet Cable RJ45 Cable Dimension (unit: mm) Recommended cable gauge: 24AWG (0.51 mm) Assembling Steps Rubber Seal 1. Drill a hole on the rubber seal plug and Plug insert an Ethernet cable through the opening. 2. Strip part of the sheath from the Ethernet cable.

  • Page 7: Mounting The Camera

    Mounting the Camera 1. Attach the supplied alignment sticker to the wall. 2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall. Then hammer the four supplied plastic anchors into the holes. 3.

  • Page 8: Network Deployment

    Network Deployment General Connection (without PoE) Pin 1 DC 12V Non-PoE Switch Pin 2 Pin 3 Pin 4 AC 24V±10% Ethernet 1. Connect RJ45 Ethernet cable to a switch. 2. Connect the AC cables from the terminal block as an alternate power source. The IO cables are user-supplied.

  • Page 9: Assigning An Ip Address

    2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN.

  • Page 10: Adjusting The Lens

    Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by doing the following: To adjust the viewing angle -- 3-axis mechanism design 1. Loosen the tilt adjustment screws and then turn the lens module up or down. Upon completion, tighten the screw.
  • Page 11 Completion 1. Attach the dome cover to the camera by combining it to the retainer and aligning with the mounting holes. 2. Secure the four dome screws with the supplied hex key wrench. Make sure all parts of the camera are securely installed.

Table of Contents