Related Manuals for Sensata Dimensions 12/800N
Summary of Contents for Sensata Dimensions 12/800N
- Page 1 DC to AC POWER INVERTERS Pure Sine Wave Output OWNER’S MANUAL MODELS: 12/800N 12/1200N 12/1500N MODELS: 12/1800N 12/2400N 12/3000N 12/3600N...
- Page 2 Typical Wiring Diagram for 12/8000N, 12/2400N, 12/3000N, & 12/3600N ............7 Typical DC Cable Connections for 12/800N, 12/1200N & 12/1500N Typical DC Cable Connections for 12/800N, 12/1200N & 12/1500N ................8 Typical DC Cable Connections for 12/1800N, 12/2400N, 12/3000N, & 12/3600N Typical DC Cable Connections for 12/1800N, 12/2400N, 12/3000N, &...
- Page 3 Laboratories Inc., File E100666. Sensata Technologies is an ISO 9001:2008 Registered Company. Sensata uses the following special notices to provide warning of possible safety related problems which could cause serious injury and to provide information to help prevent dam- age to equipment.
-
Page 4: Inverter Power Mode
Battery Safety Information: WARNING: Working in the vicinity of lead-acid batteries is dangerous. There is a risk of acid exposure. WARNING: Batteries generate explosive gases during operation. WARNING: There is risk of high current discharge from shorting a battery that can cause fire and explosion. -
Page 5: Installation Tools
The following tools are required for inverter installation: Crimper, Cable Ties, Cutter, Drill, #2 Phillips Screw Driver, Tape Measure, Wire Cutters, and Wire Strippers. Inverter Mounting Recommendations 1.5 2.5 CASE “I” Inverter Models CASE “L” 12/800N & 12/1200N, & 12/1500N CASE “O” 15.5 Inverter Models 12/1800N, 12/2400N & 12/3000N... -
Page 6: Cable Recommendations
ANN type fuses to 500A and Bussmann ANL for 600A. Cross reference the inverter model, and the estimated cable length in Table 1 to determine the proper cable gauge and fuse size. The Inverter Cable kit may be purchased directly from Sensata Technologies. - Page 7 The hardwire A.C output is not ground fault interrupt, (GFCI) protected unless the inverter has option “A”. GFCI outlets should be installed at all appropriate locations per NEC 551. The GFCI outlet should be Leviton Type 7899 or N7899, 20Amp., 125VAC. WIRING DIAGRAMS Typical Wiring Diagram for 12/800N, 12/1200N & 1500N...
- Page 8 Typical Wiring Diagram for 12/1800N, 12/2400N, 12/3000N, 12/3600N...
- Page 9 Typical DC Cable Connections for 12/800N, 12/1200N & 12/1500N...
- Page 10 Typical DC Cable Conn’s for 12/1800N, 12/2400N, 12/3000N, &12/3600N...
- Page 11 12/3000N, & 12/3600N Status Panel 12/800N & 12/1200N Plug a 100-watt light bulb into the inverter’s AC outlet. Switch on the remote On/Off switch (if available). Switch the inverter’s AC outlet On/Off for 5 seconds: then, switch it back ON. If the work light lights, the inverter works.
- Page 12 (chassis) in the battery system or poor battery cable connections. Locate and correct the short or poor connections; then, retest the system. 2. If no fuse is defective, the battery/charging system is suspect. Contact Sensata at 1-800- 553-6418 for technical assistance.
- Page 13 SPECIFICATIONS GENERAL SPECIFICATIONS 12/800N 12/1200N 12/1500N 12/1800N 12/2400N 12/3000N 12/3600N Output Power (Watts 1200 1500 1800 2400 3000 3600 Continous) Output Current (Amps AC) Up to 7 Up to 10 Up to 12.5 Up to 15 Up to 20 Up to 25...
- Page 14 Sensata and the manufacturer’s written instructions. Sensata sole liability and the Purchaser’s sole remedy for a failure of goods under this limited warranty and for any and all claims arising out of the purchase and use of the goods shall be limited to the repair or replacement of the goods that do not conform to this warranty.
- Page 15 Notes:...
- Page 16 Sensata Technologies Manufacturer of Dimensions Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000; 800-553-6418 Fax: 651-653-7600; 888-439-3565 inverterinfo@sensata.com www.dimensions.sensata.com Form No. 122187 (03/21/14) © Sensata Technologies 2014 Printed in U.S.A.