Professional vwh, vcwh, vcih, vbcv & vewdo series (2 pages)
Summary of Contents for Viking 24"
Page 1
Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.com Professional Hoods F20470H EN (080311)
All Viking Range ventilator kits are designed Protection Association (NFPA), and the Exterior Ventilator Dimensions ___________________________________________________ 25 specifically for use with Viking Range hoods. Use of any American Society for Heating, Refrigeration and non-Viking Range ventilator kit will void the hood warranty.
Dimensions & Specifications IMPORTANT– Please Read and Follow! (VWH 10”H. Wall Hoods w/Standard Ventilator 24”, 30”, & 36”) W A R N I N G To reduce the risk of injury to persons in the event of a rangetop grease fire, observe the following.
** It is recommended that the 1,500 CFM ventilator be used with longer duct runs. Max duct run is 75 ft. material used for this purpose must be covered with locally-supplied stainless steel. Viking also NOTE: Maximum amp rating for hoods includes recommended ventilator kit rating; ll products must be hard wired with 2- wire with ground.
Installing Hood Canopy Dimensions & Specifications (VBCV Wall Custom Ventilator System 30”, 36”, 42”, 48”, 54”, 60” & 66”) (Custom Hood Canopy Cutouts C C u u s s t t o o m m H H o o o o d d *For best results, M M a a k k e e s s u u r r e e t t h h e e b b a a c c k k w w a a l l l l C C a a n n o o p p y y...
Page 15
Built-In Wall Custom Ventilator Clearance Dimensions System Dimensions (VBCV Wall Custom Ventilator System) (VBCV Models 1-1/2” 7/8” 1” (3.8 cm) 1-1/2” (2.2 cm) (2.54 cm) (3.81 cm) ( C u s t o 11-1/2” (29.2 cm) 17-1/4” (43.8 cm) 6” 5/8”...
Built-In Wall Custom Ventilator Dimensions & Specifications System Dimensions (VICV Island Custom Ventilator System 36”, 42”, 54” & 66”) (VBCV Models 5-1/2” (14.0 cm) *For best results, center the unit over M M a a k k e e s s u u r r e e t t h h e e b b a a c c k k w w a a l l l l the burners of the o o f f t t h h e e c c u u s s t t o o m m h h o o o o d d cooking product...
Installing Hood Canopy Clearance Dimensions (Custom Hood Canopy Cutouts (VICV Island Custom Ventilator System) C C u u s s t t o o m m H H o o o o d d C C a a n n o o p p y y ( C u s t o ”...
Installation (VWH 10”H. Wall Hoods w/Standard Ventilator) Planning Information Proper installation of ducting is extremely 300 or 600 CFM important to ensure maximum performance Roof cap single blower from any ventilation product. interior-power 7” round duct typical ductwork • All CFMs are based on tests at 0.1 static pressure: without applying static pressure, CFM would be greatly overstated.
Slide filter front over front lip. Push filter rear up, then CAUTION: Secure vent hood to wall using screws CAUTION: If not using a duct cover, using screws slide back over rear lip. provided, make sure top mounting screws are secured provided.
Page 21
BARE OR GREEN GREEN BLACK WHITE BLACK WHITE Connect black to black, white to white, and the Attach with screws and lock washers provided. Attach with screws. Replace electrical box cover. Make connection to green/bare wire under the green screw. breaker box.
Installation Duct Cover Option (VCWH Chimney Wall Hoods) (VIH/VCIH Island Hoods) Measure distance from ceiling to canopy. Tape to avoid scratching. Check framing where cutout will be. Cut appropriate size hole in ceiling. Either 7” or 10” NOTE: 200 lb. limit. depending on your specific unit and ventillator kit.
Service & Registration Service & Parts Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.