Page 1
Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.com Professional & Outdoor Hoods F20470I EN (082012)
Dimensions & Specifications IMPORTANT– Please Read and Follow! (VWH 10”H. Wall Hoods w/Standard Ventilator 24”, 30”, & 36”) W A R N I N G To reduce the risk of injury to persons in the event of a rangetop grease fire, observe the following.
Interior Ventilator Dimensions Exterior Ventilator Dimensions (VWH 18”H. Wall Hoods) (VWH 18”H. Wall Hoods) Top View Top View 300 or 600 CFM Interior Ventilator Installation for all Wall Hoods 900 or 1200 CFM Exterior or In-Line Ventilator Installation for all Wall Hoods Top View Top View...
** It is recommended that the 1,500 CFM ventilator be used with longer duct runs. Max duct run is 75 ft. material used for this purpose must be covered with locally-supplied stainless steel. Viking also NOTE: Maximum amp rating for hoods includes recommended ventilator kit rating; All products must be hard wired with 2- wire with ground.
Interior Ventilator Dimensions Exterior Ventilator Dimensions (VCIH Chimney Island Hoods (VCIH Chimney Island Hoods Top View Top View 600 CFM Interior Ventilator Installation 900 or 1200 CFM Exterior or In-Line Ventilator Installation for all Chimney Island Hoods for all Chimney Island Hoods Top View Top View 1200 CFM Interior Ventilator Installation...
Installing Hood Canopy Dimensions & Specifications (VBCV Wall Custom Ventilator System 30”, 36”, 42”, 48”, 54”, 60” & 66”) (Custom Hood Canopy Cutouts Custom Hood Make sure the back wall *For best results, Canopy center the unit over of the custom hood the burners of the canopy is flush with the cutout so the ventilator...
Page 15
Clearance Dimensions Built-In Wall Custom Ventilator System Dimensions (VBCV Wall Custom Ventilator System) (VBCV Models For 900, 1200 or 1500 CFM Exterior For 300, 600 or 1200 CFM Interior or In-Line Ventilator Installation Ventilator Installation 900 or 1200 CFM Exterior 300 or 600 CFM Interior or In-Line Ventilator Installation Ventilator Installation...
Planning Information Built-In Wall Custom Ventilator System Dimensions (VBCV Models Proper installation of ducting is extremely important to ensure maximum performance from any ventilation product. • All CFMs are based on tests at 0.1 static pressure: without applying static pressure, CFM would be greatly overstated.
Installation (VWH 10”H. Wall Hoods w/Standard Ventilator) Check damper for unrestricted movement, adjust if Text goe here. Attach transition to damper. Seal with aluminum tape. Text goe here. CAUTION: Secure vent hood to wall using screws CAUTION: If not using a duct cover, using screws necessary.
Slide filter front over front lip. Push filter rear up, then Attach with screws and lock washers provided. Attach with screws. slide back over rear lip. Duct Cover Option (VWH 10”H. Wall Hoods w/Standard Ventilator) W A R N I N G To reduce the risk of fire, electric shock, or injury to persons, observe the following: •...
Installation (VWH 18”H. Wall & VCWH Chimney Wall Hoods) Connect black to black, white to white, and the Replace electrical box cover. Make connection to Measure down 1-13/16 (4.6 cm) from desired height of Use additional mounting screws to secure hood to green/bare wire under the green screw.
Duct Cover Option (VCWH Chimney Wall Hoods) Slide spacer front over front lip. Push spacer rear up, Slide filter front over front lip. Push filter rear up, then Measure distance from ceiling to canopy. Tape to avoid scratching. then slide back over rear lip. slide back over rear lip.
Installation (VCIH Island Hoods) Run duct work down to bottom edge of duct Attach canopy to duct cover/soffit. Seal top of hood to Check framing where cutout will be. Cut appropriate size hole in ceiling. Either 7” or 10” cover/soffit and secure in place. Make sure the duct duct with aluminum tape.
Installation (DCWH Classic Chimney Wall Hoods) Slide filter front over front lip. Push filter rear up, then Measure down 1-13/16 (4.6 cm) from desired height of Use additional mounting screws to secure hood to slide back over rear lip. hood and secure 1-1/2” x 3/4” wood strip (not wood strip.
Service & Registration Wiring Diagram Service & Parts Only authorized replacement parts may be PROFESSIONAL BUILT-IN HOODS used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.