JVC LX-P1010ZU Service Manual

Lcd data projector
Hide thumbs Also See for LX-P1010ZU:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL

Specifications

Optical mechanisms
Poly-silicon LCD panel × 3 units, Lens × 1,
Display Method
RGB shutter method, using Translucent TN liquid crystal panels
Optical System
Dichroic mirror separation, Dichroic prism composition
LCD panels
Poly-silicon TFT(Thin Film Transistor)
LCD panels × 3 (4:3 Aspect Ratio panels)
Display method : Translucent TN liquid crystal panels
Material : Poly-Silicon
Panel size : 0.7" (diagonal)
Drive method : TFT(Thin Film Transistor) active matrix panel
No. of pixels : 480,000(800 × 600)
stripe pixels × 3 panels (1,440,000 pixels)
Pixel Configuration : Stripe
Projection lens
Manual zoom/focus lens (1:1-1:1.3), F2.3-2.6, f=28mm-37mm
Lens axis shift
6:1 Low position (fixed)
Keystone distortion correction ±15˚
Screen size
30"-300" diagonal (aspect Ratio: 4:3)
Screen aspect ratio
4:3 (16:9 compatible)
Installation
desk, front/rear (menu selection)
Projector lamp
AC 130 Watts UHM Lamp
No. of colors
16,777,216 colors (Full color)
Brightness
700 lumen / ANSI
Light output uniformity
85%
Contrast ratio
300:1
RGB 800 × 600 pixels, Video 500 TV lines
Resolution
Electrical system
PC-RGB input
Display : RGB/Y • P
Type : D-sub HD 15-pin ×1
Input signal : Analog RGB standard input level
Dot clock frequency : 135MHz or less
Scanning frequency : f
HD/SYNC : TTL level, positive/negative(compatible)
DV : TTL level, positive/negative(compatible)
Accessories
•Card remote control unit •Lithium battery (CR2025) •Power cord
•Inst.book (Quick reference manual) •Inst.book (CD-ROM)
LCD DATA PROJECTOR
LX-P1010ZU/ZE
• P
IN
B
R
1pin : R/PR, 2pin:G/Y, 3pin:B/PB,
12pin : DDC data, 13pin:HD/SYNC,
14pin : VD,15pin:DDC clock
(Jack also used for component video
input.Signal type is selected on-screen.)
0.7(p-p)/75Ω terminated
24kHz-80kHz, f
50Hz-86Hz
H
V
•VGA cable •Video cable
COPYRIGHT C 2001 VICTOR COMPANY OF JAPAN, LTD.
Dimensions
:(W)276mm
(Legs are not included)
Mass
:2.5kg
Note:
The attached card remote controller becomes
necessary to adjust the following.
Keep the card remote controller also together
with the product to be repaired.
S-video input
Display : S VIDEO IN
Type : Mini Din 4-pin ×1
Input signal : Y(luminance signal) 1.0V(p-p),
Scanning frequency : f
Composite video
input Display : VIDEO IN
Type : RCA jack (yellow) ×1
Input signal : 1.0V(p-p)/75Ω terminated
Scanning frequency : Refer to S-video
Component video
input Display : RGB/Y • P
(Jack also used for composite video input.
Signal type is selected on-screen.)
Input signal : Y(luminance signal) 1.0V(p-p)/75Ω terminated
Scanning frequency : f
Audio input
Display : AUDIO IN
Type : L/R, M3 stereo mini jack ×1
Input signal : 0.32V(rms)
Serial port
Display : RS-232C
Type : Mini Din 8-pin ×1
Others
Built-in speaker
Size : 36mm round type
Output power : 0.5 Watts, Mono
Power supply
100V-240V AC, 50/60 Hz
Power consumption
210 Watts (standby mode* : 15 Watts) *with fan stopped.
Usage temperature
0˚C-40˚C(0˚F-104˚F)
Usage humidity
20%-80% (no condensation)
Storage temperature
-20˚C-40˚C (-4˚F-104˚F) , 40˚C-60˚C(104˚F-140˚F)
Storage humidity
5%-85% Normal humidity(non-condensing)
Card remote control unit
Battery : Lithium battery (CR2025), DC3V
Range for operation : approximately 7m
•Audio cable •Swivel stand unit •Carrying bag
LX-P1010ZU/ZE
×
×
(H)74mm
(D)208mm
sync negative, 75Ω terminated
C(chrominance signal) burst 0.286V(p-p),
75Ω terminated
15.75kHz, f
60Hz
H
V
(NTSC/NTSC4.43/PAL-M)
f
15.63kHz, f
50Hz
H
V
(PAL/SECAM/PAL-N)
• P
IN
B
R
P
,P
0.7V(p-p)/75Ω terminated
B
R
15.75kHz, f
60Hz (480i),
H
V
f
15.63kHz, f
50Hz (625i),
H
V
f
31.5kHz, f
60Hz (480p),
H
V
f
45kHz, f
60Hz(720p),
H
V
f
33.75kHz, f
60Hz (1080i)
H
V
(Jack used for audio of PC-RGB input,
S-video input and composite video input.)
No.PA014
Apr. 2001

Advertisement

Table of Contents
loading

Summary of Contents for JVC LX-P1010ZU

  • Page 1: Specifications

    LX-P1010ZU/ZE SERVICE MANUAL LCD DATA PROJECTOR LX-P1010ZU/ZE × × Dimensions :(W)276mm (H)74mm (D)208mm (Legs are not included) Mass :2.5kg Note: The attached card remote controller becomes necessary to adjust the following. Keep the card remote controller also together with the product to be repaired.
  • Page 2: Table Of Contents

    LX-P1010ZU/ZE Table of Contents 5.7. POWER/AUDIO SECTION SCHEMATIC Important safety precautions ...... I DIAGRAM (MAIN PWB) V-LSEP3030D1 .... 36 5.8. AD/DA/TG SECTION SCHEMATIC INSTRUCTION BOOK(CD-ROM) DIAGRAM (MAIN PWB) V-LSEP3030D1 .... 38 5.9. IO/ROM SECTION SCHEMATIC 1 SERVICE CAUTIONS AND NOTES DIAGRAM (MAIN PWB) V-LSEP3030D1 ....
  • Page 3: Service Cautions And Notes

    LX-P1010ZU/ZE 1 SERVICE CAUTIONS AND NOTES 1. In the order described in the “2.2. Disassembly Method of Cabinet 1.1. SERVICE POSITION Parts” of “2. Disassembly/Assembly Procedures”, remove the Because of this projector’s structure, service should be Bottom Case Unit. provided by turning this projector over, accordingly the 2.
  • Page 4: How To Display Lamp Operation Time (Service Mode)

    LX-P1010ZU/ZE 1.2. How to display Lamp operation time 1.3. How to initialize EEPROM IC (Service Mode) If EEPROM IC (IC2006) on Main PWB are replaced: After replacing EEPROM IC (IC2006), be sure to perform each of 1. Remove the BOTTOM CASE UNIT according to the procedures following steps in the order presented.
  • Page 5: Lamp Replacement Procedure

    LX-P1010ZU/ZE 1.4. Lamp replacement procedure Caution: Because of possibility of injury, strictly follow the replacement procedure below. 1. After the cooling fan has stopped, and STANDBY(R) ON(G) indicator turns solid red, unplug the power cord. Note: Please wait more than one hour for lamp replacement.
  • Page 6: Cleaning The Projection Lens

    LX-P1010ZU/ZE • Installation 1.5. Cleaning the Projection Lens 1. Insert the end of the Flexible Cable into the Trap Connector. Use lens cleaning paper and cleaner available at your local camera 2. Without twisting the Cable, press the Locking Tab in into its shop, etc.Dampen the cleaning paper with cleaner and gently wipe...
  • Page 7: Disassembly/Assembly Procedures

    LX-P1010ZU/ZE 2 DISASSEMBLY/ASSEMBLY PROCEDURES 2.1. DISASSEBLY FLOWCHART OF 2.2.2. Removal of the Bottom Case Unit CABINET PARTS 1. Remove 4 screws (B), 6 screws (C) and a screw (D) as shown in Fig. 2-2-2. This flowchart indicates the disassembly steps of the cabinet parts and the P.W.
  • Page 8: Optical Unit

    LX-P1010ZU/ZE 2.2.3. Removal of the Lamp Unit 1. Push the portion (a) of the Lamp Hold Lever to the direction of the arrow as shown in Fig. 2-2-4 and release the Lamp Hold Lever from the Fastening Hook. 2. Carefully pull the Lamp Unit.
  • Page 9: Removal Of The Front Cover

    LX-P1010ZU/ZE 2.2.7. Removal of the Front Cover 1. Remove 3 screws (F) as shown in Fig. 2-2-10. 2. Carefully pull and remove the portion (a) of the Front cover in the direction of the arrow with paying attention to the Tab (A).
  • Page 10: Removal Of The Optical Unit

    LX-P1010ZU/ZE 2.2.9. Removal of the Optical Unit 1. Remove the Main Grounding Plate as shown in Fig. 2-2-12. 2. Carefully pull out the Optical Unit. Fig. 2-2-12 3. Remove a screw (H) as shown in Fig. 2-2-13 and remove the Lamp Connector.
  • Page 11 LX-P1010ZU/ZE 2.2.10. Removal of the Speaker Unit 1. Detach the tape and carefully pull out the Speaker Unit as shown in Fig. 2-2-13. Fig. 2-2-14 Assembly Note: After the installation of the speaker, put on the tape in the original position.
  • Page 12: Disassebly Flowchart Of Optical Unit

    LX-P1010ZU/ZE 2.2.12. Removal of the Operation PWB 1. Remove 2 screws (J) as shown in Fig. 2-2-17. 2. releasing 2 tabs, remove the Eject Knob. 3. Remove the Remote Control Holder Unit. Fig. 2-2-19 2.3. DISASSEBLY FLOWCHART OF OPTICAL UNIT This flowchart indicates the disassembly steps of the main parts of Optical Unit.
  • Page 13: Disassembly Method Of Optical Unit

    LX-P1010ZU/ZE 2.4.2. Removal of the Lamp House Unit 2.4. DISASSEMBLY METHOD OF OPTICAL UNIT 1. Remove a screw (B) as shown in Fig. 2-4-3. 2. Remove the Lamp Duct. 2.4.1. Removal of the Polarizer Units 1. Remove 3 screws (A) to remove the Polarizer Red Unit, the Polarizer Green unit and the Polarizer Blue Unit as shown in Fig.
  • Page 14: Adjustment Procedures

    All Electrical Adjustments are performed on the “FACTORY 8. Test pattern signal (Service Engineerring Section,System ADJUST” mode which is used remote control unit instead of Engineerring Dept. JVC Projection & System Network variable resistor to control the adjustment value. Business Unit.(AVS)Consult with (AVS).) 1.
  • Page 15: How To Read The Adjustment Procedures

    LX-P1010ZU/ZE LX-P1010ZU/ZE 3.3. HOW TO READ THE ADJUSTMENT TEST POINT PROCEDURES LENS SIDE Fig. 3-4-1 MAIN PWB R5017 R3003 R5076 R3005 R5015 R3008 R3007 R5011 R5077 R5019 R5013 R5016 C5039 R3009 R3004 R5020 R5078 C5052 R5053 C5008 C2055 C5016 IC4001...
  • Page 16 LX-P1010ZU/ZE ADJ. INPUT / Test Pattern signal softwear menu TP3501 RGB Input Connector) TP3502 =6 Bar=4 3Division 3 SCALE: TP3503 EQUIPMENT SPECIFICATION OSCILLOSCOPE Refer to Description below TEST PATTERN SIGNAL Note: Fig. 3-4-5 TP3501, TP3502, TP3503: Main PWB 1. Supply Gray Scale Pattern Signal (3 scales).
  • Page 17 LX-P1010ZU/ZE INPUT / 3.4.3. VIDEO INPUT ADJUSTMENT ADJ. Test Pattern signal softwear menu Purpose: RGB Input Connector) TP3503 To set the optimum signal level. Symptom of Misadjustment: The picture will be too light or too dark. ADJ. INPUT / Test Pattern signal softwear menu...
  • Page 18: Black Level Adjustment

    LX-P1010ZU/ZE 1. Supply Gray Scale Pattern Signal (3 scales). ADJ. INPUT / Test Pattern signal softwear menu 2. Connect the oscilloscope to TP3505. (RGB Input Connector) 3. Press 5 or ∞ button on remote control to select “WHITE 70 % Red Horizontal Siganal 70 % Green Horizontal Siganal LEVEL”.
  • Page 19: White Balance Adjustment

    LX-P1010ZU/ZE 3.4.8.2. METHOD 2 ADJ. INPUT / Test Pattern signal softwear menu (RGB Input Connector) 50 % WHITE(GRAY) ADJUSTMENT SIGNAL (Right Click menu=1 Coror=9 Gray) EQUIPMENT SPECIFICATION TEST PATTERN SIGNAL LUMINANCE COLOR METER, *When vertical side of the setting is in reversal, the pattern on the screen...
  • Page 20 LX-P1010ZU/ZE 3. FULL MIRROR BULE ADJUSTMENT a. Supply 100 % White Signal and project on the screen. b. Loosen 2 Screws (C) of the Full Mirror Blue. c. Insert a (-) screwdriver into Portion (c) and move the Full Mirror Blue in the direction shown by the arrows so that color uniformity is achieved over the whole screen.
  • Page 21 LX-P1010ZU/ZE Note: This adjustment should be done in a darkroom. • POLARIZER RED ADJUSTMENT 1. Supply Black Signal (0 %) and project on the screen. 2. Loosen a Screw (A) of Polarizer Red Unit. 3. Move the Polarizer Red Unit to the right and left so that the whole screen becomes the blackest possible value, and then tighten a Screw (A).
  • Page 22: Troubleshooting Hints

    LX-P1010ZU/ZE 4 TROUBLESHOOTING HINTS Status Code Display Indications Following Status Code will be displayed in the STATUS CODE display. STATUS Symptom Problem Possible Solution CODE Lamp Unit automaticaliy 1) Confirm that all cabies are connected to Main PWB of connectors •...
  • Page 23 LX-P1010ZU/ZE STATUS Problem Possible Solution Symptom CODE • The surrounding tem- • Relocate projector to a proper location. perature of the place of • Place projector so that surrounding temperature is between 0 °C (32 °F) and 40 °C (104 °F) andthe humidity is between use may be too low.
  • Page 24 LX-P1010ZU/ZE Caution: POWER DOSE NOT Use a separate Isolation Transformer for this TURN ON unit when servicing. Because a Hot Chassis Ground is preset in the Main Power Circuit, an Isolation Transformer must be used. Turn the Power ON Lamp dose not light up...
  • Page 25 LX-P1010ZU/ZE WAVEFORM OF CHECK POINTS NO PICTURE (VIDEO INPUT) Lamp or Power circuit is defective. Is Lamp ON? See troubleshooting of "Power deos not turn on" Are all voltages at P1905 connector of Main Are all voltages at P1905 connector of Main Power circuit is defective.
  • Page 26: Schematic Diagram

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5 SCHEMATIC DIAGRAM 5.2. BLOCK DIAGRAM 5.1. SCHEMATIC DIAGRAM NOTES OVERALL SCREEN POWER SUPPLY/BALLAST 1. Important safety notice BLOCK PROJECTION Components identified by the sign ! have special characteristics important for safety. When replacing any of these components.
  • Page 27: Interconnection Schematic Diagram

    5.3. INTERCONNECTION SCHEMATIC DIAGRAM INTERCONNECTION MAIN PWB BALLAST PWB INLET PWB V-LSEP3030D1:LX-P1010ZU/ZE V- LSEP1062A1 V- LSEP1063A1 P1151 P1102 POWER CORD P1852 V-LSJA0308 : LX-P1010ZU P1904 AC_IN(L) AC_IN(L) V-VJAS0188 : LX-P1010ZE(EU) AC_IN(N) AC_IN(N) L_ON_H L_ON V-VJAS0189 : LX-P1010ZE(EK) JK5001 L_ERR L_ERR...
  • Page 28: Digital Section Schematic Diagram (Main Pwb) V-Lsep3030D1

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.4. DIGITAL SECTION SCHEMATIC DIAGRAM (MAIN PWB) V-LSEP3030D1 DIGITAL SECTION AD/DA/TG IO/ROM U2001 PNA4611M00YA U2002 PNA4611M00YA IR RECEIVER IR RECEIVER IR_R IR_F R2298 R2299 R2300 R2301 TO POWER/ UNSW5V AUDIO C2008 C2001 /PBRST IC2016 /RST DS1708SESA L2008 JK2003...
  • Page 29: Lcd Drive Section Schematic Diagram (Main Pwb) V-Lsep3030D1

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.5. LCD DRIVE SECTION SCHEMATIC DIAGRAM (MAIN PWB) V-LSEP3030D1 LCD DRIVE SECTION TP3507 P3501 LSJS07BC030 VSSY VSSY NRS2 SW15.3V NRS1 TO POWER/ C3596 UNSW5V AUDIO LCCOM SW5V VSSX SIG6 TP3504 SIG5 SIG4 SIG3 L3504 SIG2 SIG1 R3502 R3504...
  • Page 30: Rgb/Video Section Schematic Diagram (Main Pwb) V-Lsep3030D1

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.6. RGB/VIDEO SECTION SCHEMATIC DIAGRAM (MAIN PWB) V-LSEP3030D1 RGB/VIDEO SECTION L3001 TO POWER/ SW9V AUDIO RGB1 C3001 10/16V JK3001 LSJJ0125A R3001 C3002 10/16V R3002 TO IO/ROM DTV_L GREEN C3003 10/16V BLUE R3003 TO POWER/ CSYNC(MAC2) UNSW5V RED_RETURN AUDIO...
  • Page 31: Power/Audio Section Schematic Diagram (Main Pwb) V-Lsep3030D1

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.7. POWER/AUDIO SECTION SCHEMATIC DIAGRAM (MAIN PWB) V-LSEP3030D1 POWER/AUDIO SECTION IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED BY THE SINE HAVE SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE POWER ON H FROM MCON ONLY THE SPECIFIED PARTS.
  • Page 32: Ad/Da/Tg Section Schematic Diagram (Main Pwb) V-Lsep3030D1

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.8. AD/DA/TG SECTION SCHEMATIC DIAGRAM (MAIN PWB) V-LSEP3030D1 AD/DA/TG SECTION TO DIGITAL SW5V L2022 VLPS0090 POWER/AUDIO SW9V C2135 47/16V L2023 VLPS0090 L2009 Q2009 2SC563200L FBM2125HS420 C2134 10/10V 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103...
  • Page 33: Io/Rom Section Schematic Diagram (Main Pwb) V-Lsep3030D1

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.9. IO/ROM SECTION SCHEMATIC DIAGRAM (MAIN PWB) V-LSEP3030D1 IO/ROM SECTION R2003 DTV_L R2060 RGB/VIDEO S_IN_L R2061 MUTE2_H POWER/AUDIO R2062 ICE CONNECT YUV_L R2063 CPS_L R2064 RGB/VIDEO PC_NC_H R2065 P2001 S1_L R2067 POWER_ON_H R2068 LCD_ON_H R2069 STBY R2070 L_ON_H L2018 UNSW3.3V...
  • Page 34: Operation Schematic Diagram (V-Lesp0A34A1)

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.10. OPERATION SCHEMATIC DIAGRAM (V-LESP0A34A1) 5.12. OPERATION PWB (V-LESP0A34A1) OPERATION PWB OPERATION D7007 D7006 SW7005 SW7007 SW7010 LSSP0014 LSSP0014 LSSP0014 DOWN INPUT D7002 P7001 D7004 SW7002 SW7006 SW7008 SW7011 LSSP0014 LSSP0014 LSSP0014 LSSP0014 AUTO SETUP MENU ENTER RIGHT...
  • Page 35: Main Pwb (V-Lsep3030D1)

    LX-P1010ZU/ZE LX-P1010ZU/ZE 5.14. MAIN PWB (V-LSEP3030D1) MAIN PWB IO/ROM DIGITAL LCD DRIVE POWER/ IO/ROM SECTION SECTION P2001 SECTION Q2001 Q2002 AUDIO SECTION R3560 SECTION P2004 IC3502 IO/ROM FL2002 RGB/VIDEO SECTION SECTION P1901 IC3501 C2097 R2150 IC2003 FL2003 R5009 D1964 Q3513...
  • Page 36 LX-P1010ZU/ZE LX-P1010ZU/ZE MAIN PWB IO/ROM AD/DA/TG Q3503 DIGITAL SECTION SECTION P2001 FL2009 SECTION P2002 C2153 D3501 R2317 FL2011 R3526 R3529 Q3511 RGB/VIDEO R3506 R2163 R2153 TP2044 R2156 SECTION P2003 Q3505 Q3510 TP3503 D3505 R3555 R3562 R2285 R2171 R2318 Q3502 R3521...
  • Page 37: Voltage Chart

    LX-P1010ZU/ZE LX-P1010ZU/ZE 6 VOLTAGE CHART 6.3. RGB/VIDEO SECTION VOLTAGE CHART PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE 6.1.
  • Page 38: Ad/Da/Tg Section Voltage Chart

    LX-P1010ZU/ZE 6.5. AD/DA/TG SECTION VOLTAGE CHART PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE...
  • Page 39: Waveform

    LX-P1010ZU/ZE 7 WAVEFORM 0.7 V [p-p] 0.5 V [p-p] 0.5 V [p-p] 0.5 V [p-p] 0.76 V [p-p] 1.45 V [p-p] 3.5 V [p-p] 3.5 V [p-p] 1.45 V [p-p] 1.45 V [p-p] 3.5 V [p-p] 10 V [p-p] 10 V [p-p]...
  • Page 40: Parts List

    LX-P1010ZU/ZE IMPORTANT SAFETY NOTICE: 8 PARTS LIST COMPONENTS IDENTIFIED BY THE SIGN ! HAVE SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. 8.1. EXPLODED VIEW WHEN REPLACING ANY OF THESE COMPONENTS, USE (BOTTOM CASE SECTION)M1 ONLY THE SPECIFIED PARTS. (PA014) 52...
  • Page 41: Top Chassis Section

    LX-P1010ZU/ZE IMPORTANT SAFETY NOTICE: 8.2. EXPLODED VIEW COMPONENTS IDENTIFIED BY THE SIGN ! HAVE (TOP CHASSIS SECTION)M2 SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS. 53 (PA014)
  • Page 42: Optical Block Section

    LX-P1010ZU/ZE IMPORTANT SAFETY NOTICE: 8.3. EXPLODED VIEW COMPONENTS IDENTIFIED BY THE SIGN ! HAVE (OPTICAL BLOCK SECTION)M3 SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS. (PA014) 54...
  • Page 43: Top Cover Section

    LX-P1010ZU/ZE IMPORTANT SAFETY NOTICE: 8.4. EXPLODED VIEW COMPONENTS IDENTIFIED BY THE SIGN ! HAVE (TOP COVER SECTION)M4 SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS. 55 (PA014)
  • Page 44: Front Cover Section

    LX-P1010ZU/ZE IMPORTANT SAFETY NOTICE: 8.5. EXPLODED VIEW COMPONENTS IDENTIFIED BY THE SIGN ! HAVE (FRONT COVER SECTION)M5 SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS. (PA014) 56...
  • Page 45: Packing Section

    LX-P1010ZU/ZE 8.6. EXPLODED VIEW (PACKING SECTION)M6 57 (PA014)
  • Page 46: Assembly Parts List

    LX-P1010ZU/ZE 8.7. ASSEMBLY PARTS LIST PARTS LIST (BOTTOM CASE SECTION)M1 REF No. PART No. PART NAME, DESCRIPTION V-LSVQ0037 BOTTOM CASE UNIT US (LX-P1010ZU) V-LSVQ0038 BOTTOM CASE UNIT EU (LX-P1010ZE) V-LSYF0485 LAMP COVER UNIT V-LSYF0475 LENS CAP UNIT V-LSGK0079 JACK DOOR...
  • Page 47 FUSE 250V 5A(INLET PWB ASS'Y) F1102 V-MTG4A50121C FUSE 250V 4A(INLET PWB ASS'Y) PARTS LIST (PACKING AND ACCESSORY ASS'Y)M6 REF No. PART No. PART NAME, DESCRIPTION V-LSPG1131 PACKING CASE EU(LX-P1010ZU) V-LSPG1132 PACKING CASE EU(LX-P1010ZE) V-LSPN0204 CUSHION(LEFT) V-LSPN0205 CUSHION(RIGHT) V-VPFS0054 V-LSPN0208 ACCESSORY PAD(L)
  • Page 48 LX-P1010ZU/ZE VICTOR COMPANY OF JAPAN, LIMITED Printed in Japan (No.PA014) 0104(V)

This manual is also suitable for:

Lx-p1010ze

Table of Contents