Connecting The Power; Connecting The Supplied Power Cord; Turning On The Power; Turning On The Power From The Remote Conroller - Integra DTR-7.4 Instruction Manual

Connecting the Power

Standby/On
Standby indicator
Display Dimmer
Standby/On
Standby
Direct / Pure Audio Stereo Surround THX
Pure Audio Upsampling
Phones Zone 2 ( GRN )
Rec ( RED )
Audio DVD Video 1 Video 2 Video 3 Video 4 Video 5
Selector
VCR 1 VCR 2
On
On Standby
Standby
1
@. - ' / ABC
4
GHI
7
PQRS
+10
--/---
Custom
Macro
Scroll Wheel
Mode
Dimmer
T V
Input
+
CH
Disc
-
Display
Rec
Audio Subtitle
Surround
Repeat A-B
Pure A Direct
Test Tone CH SEL
Playlist Album
Audio SEL
Caps Delete
• Before you plug in the DTR-7.4, confirm that all con-
nections have been made properly.
• Turning on the power may cause a momentary power
surge, which might interfere with other electrical
equipment on the same circuit, such as computers. If
this happens, use a wall outlet on a different circuit.

Connecting the Supplied Power Cord

Plug the supplied power cord into this AC INLET.
• Do not use a power cord other than the one supplied
with the DTR-7.4. The power cord supplied is
designed for use with the DTR-7.4 and should not be
used with any other device.
• Never have the power cord disconnected from the
DTR-7.4 while the other end is plugged into the wall
outlet. Doing so may cause an electric shock. Always
connect by plugging into the wall outlet last and dis-
connect by unplugging from the wall outlet first.
AC INLET
Power cord
(supplied)
Rec Out Zone 2 Of f
Master Volume
Setup
Tuning
Enter
Return
Preset
DSP Memory FM Mode
A-FO RM Listening Mode Memory
Clear
Video 5 Input
Tape Tuner Phono CD Net Audio
Digital S Video Video L Audio R
DTR-7.4
To wall outlet
T V
Input
+
2 3
DEF TV CH
5 6 -
JKL MNO
8 9
TUV WXYZ
TV VOL
0 Clear
Direct Tuning
Zone 2
Input
Sleep
Enter VOL
Muting
Step / Slow Random
Angle
Last Memory
THX All CH ST Stereo
Search Memory
DSP DSP
Level - Level +
Ar tist Genre
L Night Re-EQ
Language Loca t ion
RC- 550 M
DO NOT con-
nect the
power cord at
this time.

Turning on the Power

1
Plug the power cord into an AC
wall outlet.
Standby
The Standby indicator will light up.
2
Press the Standby/On button to
Standby/On
turn on the DTR-7.4.
The display will light up and the Standby
indicator will turn off.
If you press the Standby/On button
again, the DTR-7.4 returns to the standby
Standby
state.
Turn off
Turning on the Power from the
Remote Controller
Before you can use the remote controller, you must
perform steps 1 above and place the DTR-7.4 in the
standby state.
1 Press the scroll wheel.
"AMP" appears on the remote control-
ler's display. This is the mode for con-
trolling the DTR-7.4.
2
Press the On button to turn on the
DTR-7.4.
On
To set the DTR-7.4 to Standby, press the
Standby button.
Note:
Any components connected via
on when the remote controller's On button is pressed.
Memory backup
The DTR-7.4 uses a battery-less memory backup sys-
tem in order to retain radio presets and other settings
when it is unplugged or in the case of a power failure.
Although no batteries are required, the DTR-7.4 must
be plugged into an AC outlet in order to charge the
backup system.
Once it has been charged, the DTR-7.4 will retain the
settings for several weeks, although this depends on the
environment and time will be shorter in humid climates.
will also be turned
27