Connecting; Compatible Av Components; Connections For Remote Control - Integra DTR-7.4 Instruction Manual

Connecting

The terminal on the DTR-7.4 is for connecting other
Integra/Onkyo components equipped with the same
terminal. When a component is connected to the
terminal, it can be operated by the remote controller
supplied with the DTR-7.4. In addition, when you
connect a component to the
perform the system operations given below.
Power on/ready function
When the DTR-7.4 is in the standby state, if an
connected component is turned on, the DTR-7.4 also
turns on and the input source selected at the DTR-7.4
automatically switches to that component.
Be aware that this function will not work if the power cord for the
-connected component is connected to the AC OUTLET on
the DTR-7.4, or if the DTR-7.4 has already been turned on.
Direct change function
When the play button is pressed on an
component, the input source selected at the DTR-7.4
automatically changes to that component.
Power off function
When the DTR-7.4 is placed in the standby state, all
-connected components are also automatically put
into the standby state.
Also, if you press the On button on the DTR-7.4 remote
controller while the DTR-7.4 is turned on, all
connected components (DVD players, CD players, MD
recorders, tuners, etc.) are also turned on.

Connections for Remote Control (

To connect components using the
connect a remote control cable from this
terminal of the other component. An
cable with a 1/8 inch (3.5 mm) miniature two-conductor plug
comes with every cassette tape deck, compact disc player,
MD recorder, and DVD player that has an
Integra/Onkyo DVD player
DIGITAL OUT
COAX
DIGITAL
IN
R
COAX
1
DIGITAL PRE OUT
IN ANTENNA
R L
COAX FRONT
1
SUB
CENTER
AM
2
SURR
3
SURR
R L
BACK/
OPT
ZONE 2
FM
1
75
FRONT
MULTI CH
2
INPUT
AUDIO
R L
R L
SUB CENTER
3 PHONO
IN
SURR
DIGITAL
IN
OUT
R L
OPT
OUT
1
SURR
BACK
TAPE
2
IN
GND
R L
AUDIO
26

-compatible AV Components

terminal, you can also
-connected
terminal, simply
terminal to the
remote control
terminal.
REMOTE
CONTROL
L
R
Remote
ANALOG
OUTPUT
control
cable
AUDIO
L REMOTE
CONTROL
IN
AUDIO VIDEO S VIDEO COMPONENT
VIDEO FRONT SPEAKERS
MONITOR OUTPUT
R L
OUT
Y
R L
OUT ZONE 2 P
B
IN DVD P
R
INPUT 1
OUT Y
ETHERNET
(Net -Tune)
VIDEO 1
CENTER
IN P B
SPEAKER
OUT P
R
VIDEO 2
INPUT 2
CD IN Y
I R
IN
RS232
IN VIDEO 3 P B
IN VIDEO 4 P R
OUT
R L
AUDIO VIDEO S VIDEO
• When performing operations with
components using the
remote zone (Zone 2).
• For remote control operation, the audio connection
cables must also be connected.
• If a component has two
either one to connect to the DTR-7.4. The other one
can be used to daisy chain with another component.
-
• With Integra/Onkyo DVD players, you can enter the
pre-program code so that you can operate the DVD
player directly with the remote controller without
connecting the
Ex: Onkyo cassette tape
-
deck
)
SURR SPEAKERS
R L
R L
A
A ZONE 2
12 V
TRIGGER OUT
B REMOTE
CONTROL
system, do not use the
terminals, you can use
terminals (See page 89).
DTR-7.4
REMOTE
CONTROL
connector
Ex: Integra/Onkyo CD
player
connector
Remote control cable
-connected