VADDIO HD-18 Installation And User Manual
High definition ptz camera featuring the hd-18 quick-connect sr
Hide thumbs
Also See for HD-18:
- Installation and user manual (14 pages) ,
- Manual (4 pages) ,
- Installation and user manual (9 pages)
Table of Contents
Advertisement
Quick Links
Camera and Electronic Products for Integrators
Vaddio™ WallVIEW™ HD-18
High Definition PTZ Camera featuring the HD-18 Quick-Connect™ SR
Model Number 999-6905-000W (North America)
Model Number 999-6905-001W (International)
Arctic White Version
HD-18 Quick-Connect SR Interface
©2010 Vaddio - All Rights Reserved. WallVIEW HD-18 - Document Number 341-888 Rev. C
Installation and User Guide
Model Number 999-6905-000 (North America)
Model Number 999-6905-001 (International)
Advertisement
Table of Contents
Related Manuals for VADDIO HD-18
Summary of Contents for VADDIO HD-18
- Page 1 High Definition PTZ Camera featuring the HD-18 Quick-Connect™ SR Model Number 999-6905-000 (North America) Model Number 999-6905-001 (International) Model Number 999-6905-000W (North America) Model Number 999-6905-001W (International) Arctic White Version HD-18 Quick-Connect SR Interface ©2010 Vaddio - All Rights Reserved. WallVIEW HD-18 - Document Number 341-888 Rev. C...
- Page 2 50dB, delivering clean, clear video. The 7-element Wide Dynamic Zoom lens allows WallVIEW HD-18 to capture a wide angle of view (55.2°) enough to view everyone at a conference room table, as well as capture an individual from a long distance (3.2°).
- Page 3 Tally Light – A tally light is illuminated when the camera receives a VISCA command from an external control system and tally is triggered. IR Sensors – Dual IR sensors are built into the front of the WallVIEW HD-18 to receive IR signals from the IR remote control supplied with the camera.
- Page 4 HD Video Select – A rotary switch allows the user to choose the component HD output video resolution and format. See page 6 for additional information on switch settings. 12 VDC Input – NOTE: The power input is not used with the WallVIEW HD-18 system. This is only used on the standard, ClearVIEW HD-18 camera.
- Page 5 First Time Set-up with the WallVIEW HD-18: WallVIEW HD-18 was designed to be exceptionally easy to use and operate. There is documentation at the back of the manual for pin-outs for all of the connectors on the WallVIEW HD-18 camera. Getting Started: First, set up the HD and SD output resolutions for the camera, along with IR output, baud rate and image flip.
- Page 6 For RS-232, use a standard CAT-5 cable (568B termination for RJ-45 connectors) from the RS-232 port on the back of a Vaddio ProductionVIEW camera controller or switcher. If the camera will be connected to a third-party control system (such as AMX or Crestron), a DB-9 to RJ-45 adapter cable is supplied with the camera for RS-232.
- Page 7 Pre-wire all cabling as required (see wiring diagram examples). • The Thin Profile Wall Mount for the WallVIEW HD-18 can be mounted directly to a 2-gang wall box or can be mounted to the drywall using four dry wall anchors.
- Page 8 Place the camera onto the camera mount and use the ¼”-20 screws to secure the camera to the mount. Step 4: Connect the Vaddio 24 VDC power supply to an AC outlet. Power will travel down the Power/Video Cat. 5 cable to the camera. The camera will “Home” to a centered position ready for control information from the IR remote control or RS-232 camera controller of the integrators’...
-
Page 9: Compliance And Ce Declaration Of Conformity
This device must accept any interference including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the user’s authority to operate this equipment. ICES-003 Compliance This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. -
Page 10: Warranty Information
Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if the unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products. - Page 11 Video Output: DE-15 connector for HD Analog Component (Y,PB,PR) video only – no SD video IR Output: Transmits modulated or non-modulated IR signals received from the HD-18 IR receiver Control In RJ-45: Accepts RS-232 from ProductionVIEW or other non-daisy-chain control systems Control Out RJ-45: Sends RS-232 from Quick-Connect SR to the camera Up to 100’...
-
Page 12: Appendix 2: Camera Dimensions
Appendix 1: Video Pin-out Table for WallVIEW HD-18 YPbPr Pr GND Y GND Pb GND EZCamera Power & HD Video RJ-45 Connector Pin-outs For HD-18 Camera and Quick-Connect HD-18 SR (568B Wiring Standard) YPbPr Power+ Power- 12345678 PB GND Y GND Appendix 2: Camera Dimensions WallVIEW HD-18 Manual 341-888 Rev. -
Page 13: Appendix 3: Communication Specification
The Vaddio ClearVIEW HD-18 Control Protocol is similar, but not identical to the Sony™ NOTE: VISCA™ command set in order to be compatible with several popular control devices. Not all VISCA commands are supported and there are many HD-18 specific commands in the following Command and Inquiry Lists. HD-18 Command List (1/2) - Page 14 81 01 04 01 03 FF ICR Off Additional Information: Pan Range: 8044 – 7FBC (-32,700 to +32,700) Tilt Range: E891 – 4C2B (-5,999 to +19,499) * Actual Pan/Tilt ranges defined in Inquiry list WallVIEW HD-18 Manual 341-888 Rev. C Page 14 of 16...
- Page 15 50 00 00 0p 0q FF pq: ExpComp Pos -Iris Position CAM_ICRModeInq 81 09 04 01 FF y0 50 02 FF ICR On y0 50 03 FF ICR Off WallVIEW HD-18 Manual 341-888 Rev. C Page 15 of 16...
- Page 16 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2010 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, ProductionVIEW, Quick-Connect, ControlVIEW, WallVIEW, EZCamera and PowerRite are registered trademarks of Vaddio.
Need help?
Do you have a question about the HD-18 and is the answer not in the manual?
Questions and answers