VADDIO CLEARVIEW HD-18 Installation And User Manual
High-definition ptz camera
Hide thumbs
Also See for CLEARVIEW HD-18:
- Installation and user manual (16 pages) ,
- Manual (4 pages) ,
- Installation and user manual (9 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VADDIO CLEARVIEW HD-18
Summary of Contents for VADDIO CLEARVIEW HD-18
- Page 1 Installation and User Guide Camera and Electronic Products for Integrators ™ C VIEW™ HD-18 ADDIO LEAR High-Definition PTZ Camera Model Number 999-6900-000 (North America) Model Number 999-6900-001 (International) ©2010 Vaddio - All Rights Reserved. ClearVIEW HD-18 - Document Number 341-885 Rev. B...
- Page 2 50dB, delivering clean, clear video. The multi-element Wide Dynamic Zoom lens allows ClearVIEW HD-18 to capture a wide angle of view (55.2°) enough to view everyone at a conference room table, as well as capture an individual from a long distance (3.2°).
- Page 3 Tally Light – A tally light is illuminated when the camera receives a VISCA command from an external control system and tally is triggered. IR Sensors – Dual IR sensors are built into the front of the ClearVIEW HD-18 to receive IR signals from the IR remote control supplied with the camera.
- Page 4 First Time Set-up with the ClearVIEW HD-18: ClearVIEW HD-18 was designed to be exceptionally easy to use and operate. There is documentation at the back of the manual for pin-outs for all of the connectors on the ClearVIEW HD-18 camera. Getting Started: First, set up the HD and SD output resolutions for the camera, along with IR output, baud rate and image flip.
- Page 5 IR Remote Operation: Follow the instructions provided with the IR Remote for moving the camera, as well as setting preset camera positions. Figure 5: Dip Switch and HD Video Output Resolution Setting Options for the ClearVIEW HD-18 Camera DIP SWITCH SETTINGS HD VIDEO SELECT 720p/59.94...
-
Page 6: Optional Accessories
ClearVIEW HD-18 Figure 6: Standard wiring configuration of the camera to a Vaddio Joystick controller. Rear Panel of ClearVIEW HD-18 YPbPr HD Monitor RS-232 (Simulated Feed) 12V - 3A PowerRite Power Supply ProductionVIEW Precision Camera Controller NOTE: Strain relief for the 15-pin connector on the back of the camera is highly recommended. -
Page 7: Compliance And Ce Declaration Of Conformity
This device must accept any interference including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the user’s authority to operate this equipment. ICES-003 Compliance This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. -
Page 8: Warranty Information
Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if the unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products. - Page 9 Y GND Pb GND EZCamera Power & HD Video RJ-45 Connector Pin-outs For HD-18 Camera and Quick-Connect HD-18 SR ONLY (568B Wiring Standard) YPbPr Power+ Power- 12345678 PB GND Y GND ClearVIEW HD-18 Manual 341-885 Rev. B Page 9 of 14...
-
Page 10: Appendix 3: Communication Specification
ClearVIEW HD-18 Appendix 2: ClearVIEW HD-18 Dimensions Appendix 3: Communication Specification ClearVIEW HD-18 Manual 341-885 Rev. B Page 10 of 14... -
Page 11: Command List
TXD (to RXD of control source) No Flow control The Vaddio ClearVIEW HD-18 Control Protocol is similar, but not identical to the Sony™ NOTE: VISCA™ command set in order to be compatible with several popular control devices. Not all VISCA commands are supported and there are many HD-18 specific commands in the following Command and Inquiry Lists. - Page 12 81 01 04 01 03 FF ICR Off Additional Information: Pan Range: 8044 – 7FBC (-32,700 to +32,700) Tilt Range: E891 – 4C2B (-5,999 to +19,499) * Actual Pan/Tilt ranges defined in Inquiry list ClearVIEW HD-18 Manual 341-885 Rev. B Page 12 of 14...
- Page 13 50 00 00 0p 0q FF pq: ExpComp Pos -Iris Position CAM_ICRModeInq 81 09 04 01 FF y0 50 02 FF ICR On y0 50 03 FF ICR Off ClearVIEW HD-18 Manual 341-885 Rev. B Page 13 of 14...
- Page 14 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2010 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, ProductionVIEW, ClearVIEW, EZCamera, ControlVIEW and PowerRite are registered trademarks of Vaddio.
Need help?
Do you have a question about the CLEARVIEW HD-18 and is the answer not in the manual?
Questions and answers