Table of Contents
Advertisement
Quick Links
24 VOLT CORDLESS
SET up AnD OpERATing inSTRuCTiOnS
Distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THiS mAnuAL.
©
Copyright
2009 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements,
actual product may differ slightly from the product described herein.
For technical questions or replacement parts, please call 1-800-444-3353.
AngLE gRinDER
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
. All rights reserved. No portion of this manual or any artwork
66672
®
.
Advertisement
Table of Contents
Related Manuals for Chicago Electric 66672
Summary of Contents for Chicago Electric 66672
- Page 1 24 VOLT CORDLESS AngLE gRinDER 66672 SET up AnD OpERATing inSTRuCTiOnS ® Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
-
Page 2: Important Safety Information
Do not use any adapter not avoided, could result in plugs with grounded power tools. minor or moderate injury. SKU 66672 For technical questions, please call 1-800-444-3353. Page 2... - Page 3 ANSI-approved and breath- use personal protective equip- ing protection must be NIOSH-ap- ment. Always wear eye protection. proved for the specific hazards in the Safety equipment such as dust mask, work area. SKU 66672 For technical questions, please call 1-800-444-3353. Page 3...
- Page 4 SKU 66672 For technical questions, please call 1-800-444-3353. Page 4...
-
Page 5: Grinding, Sanding Or Wire Brushing Operation Safety Warnings
The arbor size of wheels, flanges, Fragments of work piece or of a backing pads or any other acces- SKU 66672 For technical questions, please call 1-800-444-3353. Page 5... - Page 6 • Lead from lead-based paints ing, contact Harbor Freight Tools for a • Crystalline silica from bricks and ce- replacement. ment or other masonry products • Arsenic and chromium from chemi- SKU 66672 For technical questions, please call 1-800-444-3353. Page 6...
-
Page 7: Kickback And Related Warnings
Such blades create frequent the edge of the wheel that is entering into kickback and loss of control. SKU 66672 For technical questions, please call 1-800-444-3353. Page 7... -
Page 8: Safety Warnings Specific For Grinding Operations
SKU 66672 For technical questions, please call 1-800-444-3353. Page 8... -
Page 9: Grounded Tools: Tools With Three Prong Plugs
If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk SKU 66672 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Double Insulated Tools: Tools With Two Prong Plugs
Association, and the National Electri- use. cal Code. (See Outlets for 2-prong plug.) Make sure the extension cord is prop- erly wired and in good electrical con- SKU 66672 For technical questions, please call 1-800-444-3353. Page 10... - Page 11 150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions per Minute n 0 xxxx/min. (RPM) SKU 66672 For technical questions, please call 1-800-444-3353. Page 11...
-
Page 12: Specifications
Bolt and Nut (17, 18) subheadings therein before set to secure the Guard in place - See up or use of this product. Figure 2. SKU 66672 For technical questions, please call 1-800-444-3353. Page 12... - Page 13 Spindle (14) - See Figure 6. through the arbor hole. Thread the Clamp Nut (20) onto the Spindle. Wrench tighten only enough so that the wheel is securely held on SKU 66672 For technical questions, please call 1-800-444-3353. Page 13...
-
Page 14: Charging The Battery
80 minutes for the battery to cool down first. After the charging cycle is completed, al- low the Battery to cool prior to use. REV 09f SKU 66672 For technical questions, please call 1-800-444-3353. Page 14... -
Page 15: Operating Instructions
OpERATing inSTRuCTiOnS TO pREVEnT SERiOuS injuRY: Grip the tool firmly in both hands. Grinder Battery Figure 10 Button Install the charged Battery onto the Grinder - See Figure 10. SKU 66672 For technical questions, please call 1-800-444-3353. Page 15... -
Page 16: Maintenance And Servicing
TO pREVEnT SERiOuS service technician. injuRY FROm TOOL FAiLuRE: Do not use damaged equipment. if abnormal noise or vibration occurs, have the problem corrected before further use. SKU 66672 For technical questions, please call 1-800-444-3353. Page 16... -
Page 17: Troubleshooting
Power shuts off to Circuit breaker tripped. Check circuit breaker and flip switch if tool while running. tripped. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. SKU 66672 For technical questions, please call 1-800-444-3353. Page 17... -
Page 18: Parts List
Battery Charger (not shown below) Transformer (not shown below) pARTS DiAgRAm note: Some parts are listed and shown for illustration purposes only, and are not available indi- vidually as replacement parts. SKU 66672 For technical questions, please call 1-800-444-3353. Page 18... -
Page 19: Limited 90-Day Warranty
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 Record product’s Serial number Here: note: If product has no serial number, record month and year of purchase instead. SKU 66672 For technical questions, please call 1-800-444-3353. Page 19...