Sony CDX-GT520 Operating Instructions Manual page 20

FM/AM
Compact Disc Player
SON~
Installation/Connections
3-217-595-11 (1)
6
A
SUB OUT (MONO)
Installation/Connexions
-
Bo
BUS AUDIO IN
Source selector*
Selecteur de source*
XA.. C40
CDX-GT520
CDX-GT52W
BUS CONTROL IN *
not supplied
non fourni
© 2007 Sony Corporation Printed in Thailand
Notes (fJ-A)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Tips (fJ-B)
• When connecting only a single Co/Mo changer or other
optional device, connect directly to this unit.
• For connecting two or more Co/Mo changers or other
optional devices, the source selector XA-C40 (not supplied) is
necessary.
o
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
f) To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with
a
manually-operated telescopic antenna (aerial).
• When your car has
a
built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
e
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
o
To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If
there is no accessory position, connect to the + 12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
o
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to
a
metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies + 12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
• The numbers in the list are keyed to those in the
instructions.
• The bracket
CD
and the protection collar
@
are
attached to the unit before shipping. Before mounting
the unit, use the release keys
®
to remove the bracket
CD
from the unit. For details, see "Removing the
protection collar and the ·bracket (EI)" on the reverse
side of the sheet.
• Keep the release keys
®
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
CD
carefully to avoid injuring your
fingers.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power supply leads only
after all other leads have been connected.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
®
x2
Power amplifier
Amplificateur de puissance
CD/MD
changer
Changeur de CD/MD
x4
®
®
Rear speaker
Haut-parleur arriere
Front speaker
Haut-parleur avant
Equipment used in illustrations (not supplied)
Appareils utilises dans les illustrations (non fournis)
o
Catch
Active subwoofer
Caisson de graves actif
Rotary commander RM-X4S
Satellite de commande RM-X4S
Note
Before installing, make sure that the catches on both sides of
the bracket
CD
are bent inwards 2 mm (3/32 in).
If
the catches are
straight or bent outwards, the unit will not be installed securely
and may spring out.