Optional Accessories - Sony SRW-5800 Operation Manual

A full range of editing functions
Two SRW-5800 units can be connected allowing
automatic or manual assemble and insert editing. The VTR
also features a full range of editing functions, including
preview, review, preroll, and the setting or changing of edit
points.
Quick access to edit points
The following methods are provided for the setting of edit
points:
• Multi-cuing for up to 100 edit points
• Search dial with shuttle and jog functions
• Direct input through numeric buttons
DMC (Dynamic Motion Control) editing
®
Using the DT (Dynamic Tracking) heads, you can play
back a section of an edit at speeds between –1 and +2 times
normal speed and store the speed variation in memory for
later use in automatic editing.
Note
When this unit is used as a player, DMC playback cannot
be selected for HDCAM-SR format.
Split editing
In insert mode, audio and video edit points can be set
separately.
Audio editing
With this unit, only fade-in and fade-out can be performed.
Note
When edited audio is played with this unit, fade-out/fade-
in processing is carried out in normal-speed playback only.
To play the same edited audio with the SRW-5000/5500,
upgrading of internal software may be required.
Display of duration between edit points
The duration between any two of IN, OUT, AUDIO IN, or
AUDIO OUT points can be displayed by simultaneously
pressing two buttons corresponding to those edit points.
Digital time counter
The time counter display shows CTL and time codes
3)
(LTC/VITC ), or user bits data for precise setting of edit
points.
3) LTC (Longitudinal Time Code):
Time code recorded on a longitudinal track
VITC (Vertical Interval Time Code):
Time code recorded on a video track during the vertical blanking interval

1-2 Optional Accessories

The following accessories can be used with this unit.
HKSR-5001 Format Converter Board
This allows format conversion described below:
• 2-3 pulldown (23.98PsF to 59.94i, 24PsF to 60i)
• Conversion between 1080 and 720P
• 4:2:2 between 4:4:4
(Conversion of 4:4:4 to 4:2:2 is possible only when the
HKSR-5803SQ or HKSR-5803HQ is additionally
installed.)
Note
When the serial number of this unit is 12001 or higher, the
format conversion above is available when the HKSR-
5001 is installed. The HKSR-5803SQ or HKSR-5803HQ
is not required for the format conversion above.
For details on format conversion, see "Recording and
playback tape formats and conversion output" on
page 199.
HKSR-5802 Digital Betacam/HDCAM Processor
Board
This allows you to play back Digital Betacam or HDCAM
tapes and output SD and HD signals.
When the system is operated in 4:4:4 mode, up conversion
of the output to HD signals are possible as follows,
depending on the system setting.
1080: Up conversion to 1080.
720: Up conversion to 720P.
When the system is operated in 4:4:4 mode, no up-
converted HD output can be obtained.
HKSR-5803SQ RGB SQ Processor Board
This allows you to accept dual link HD SDI input, and
record and play back in RGB (4:4:4) SQ mode.
Note
When the serial number of this unit is 12001 or higher,
recording and playing back in RGB (4:4:4) SQ mode do
not require the HKSR-5803SQ.
HKSR-5803HQ Advanced HQ Processor Board
This allows double-speed playback for the applicable
system settings (see page 11). Also, recording and
playback for the for the 4:2:2/1080/50P, 59P, or 60P signal
and the dual-stream (3D) signal are supported. Normal-
speed recording and playback in RGB (4:4:4) HQ mode as
well as RGB (4:4:4) SQ mode are also supported.
Note
When the serial number of this unit is 12001 or higher,
recording and playback at normal speed in RGB (4:4:4)
13
1-2 Optional Accessories