Alto LYNX-MIX244 User Manual page 10

4. CONTROL ELEMENTS
17 ASSIGNMENT Switches
Each channel provides four push-buttons: SUB1-2, SUB3-4, MAIN L-R and SOLO.
Pressing the SOLO button, the corresponding SOLO LED will illuminate and the
SOLO signal will replace other signals send to the Headphone/Control Room and
Meters. We suggest use the SOLO function in live work to preview channels
before they are let into the mix. It is useful to set an instrument's input level and
EQ, and you can also solo any channel that you want to. The SOLO switch never
affects any mix other than the Control Room. The other three buttons can be
considered as signal assignment switches. Pressing the SUB1-2 will assign the
channel signal to Subgroup1/2, you can depend on the PAN switch to adjust the
amount of channel signal sent to the SUB1 versus SUB2, when
completely left, then the signal can be only controlled by Subgroup1 and vice-
versa. In the same way, pressing the SUB3-4 or MAIN L/R will assign the channel
signal to Subgroup3/4 or MAIN MIX L/R, and will also be affected by PAN.
18 FADER
This fader will adjust the overall level of this channel and set the amount of signal
send to the main output.
19 Master AUX SENDS Controls
These four controls are used to determine the master AUX SEND levels, which
can be varied from - to +15 dB. When the external effect units which
no input gain control were connected to mixer, you can get a further +15 dB
gain available from these Aux Send outputs. As to the AUX4, it can also provide
the lovable level adjustment for the internal effect signal.
20 SOLO Button
The function of these SOLO buttons are the same as the channel SOLO button,
they can also be affected by the SOLO MODE switch. Press the Solo button,
the AUX sends ( 1~3) will be routed to the Ctrl Room/Phones outputs and
Meters display.
21 Master STEREO AUX RETURNS Controls
These two controls set the level that received from the stereo AUX RETURN
connectors, which can be varied from -
further gain for low level effects.
22 TO AUX SEND1/2
The both rotary knobs assign the AUX RETURN 2 signals to their respective
AUX SEND outputs: The "TO AUX SEND1" assign the signal to AUX SEND1
bus, and the "TO AUX SEND2" assign the signal to AUX SEND2 bus. The
adjustable range goes from -
8
the PAN
to +15 dB. They are used to provide the
to +15 dB.
internal DSP module and the signal level can be controlled by the EFFECTS
OUT (37) control.
48 CTRL OUT Jacks
These 1/4" phone jacks will be used to send the Control Room signal to the
studio monitor speakers or a second set of PA.
49 PHONES Jacks
These jacks will be used to send the signal to a pair of headphone or to powered
studio monitors.
turned
50 MONO OUTPUT Jack
This 1/4" phone jack is balanced/unbalanced mono mix output connector, it can
be regarded as a sum output of the left and right of MAIN MIX.
51 2-TRACK IN/OUT
- TAPE IN
Use the Tape input if you wish to listen to your mix from a Tape Recorder or DAT.
- TAPE OUT
These RCA jacks will route the main mix into a tape recorder.
Rear Panel
has
54
52 POWER Switch
This switch is used to turn the main power on and off.
53 +48 Volt Phantom Power
It is available only to the XLR MIC sockets. Never plug in a microphone when
phantom power is already on. Before turning phantom power on, make sure
that all faders are totally down. In this way, you will protect your stage
monitors and main loudspeakers.
54 AC Inlet with FUSE Holder
Use it to connect your L YNX-MIX244 mixer to the main AC with the supplied
AC cord. Please check the voltage available in your country and how the
voltage for your L YNX-MIX244mixer is configured before attempting to connect
your L YNX-MIX244 mixer to the main AC.
3. CONTROL ELEMENTS 4. CONTROL ELEMENTS
52 53
POWER PHANTOM CAUTION
ON
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD
- DO NOT OPEN
OFF
AVIS: RISQUE DE CHOC ELECTRIQUE
- NE PAS OUVRIR
Apparaten skall anslutas
CAUTION:
till jordat uttag nar den
ansluts till ett natverk
AC INPUT
REPLACE WITH THE SAME TYPE FUSE AND RATING
100-240V 50/60Hz
Fuse: T-1.6AL
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
RATED POWER CONSUMPTION: 70W
MODEL
SERIAL
13