Table of Contents
Advertisement
5
PROGRAMMING
Setting Your Energy Saving Programs cont..
5.4
Using Quick Program Groups or Individual Day Programming cont..
5.4.2
Weekend –
allows you to program the weekend days (SA, SU will show in the display) at the same time.
Again, individual day programming can be used to change specific setpoint times or
temperatures.
Individual Days –
allows you to program each day of the week individually to give you the greatest schedule
flexibility. Often used to fine tune programming after initially programming the thermostat
using Whole Week, Weekday or Weekend groups.
IMPORTANT NOTE!
When in group
selection, the thermostat will check if all of the
days of that group have the same program
setpoint times and temperatures. If so, the
time and temperature of the individual setpoint
(MORN, DAY, EVE, NIGHT) will be displayed.
Otherwise, the individual setpoint time and
temperature will be blanked. User is allowed to change the daily programs for this
setpoint time and temperature by pressing the
daily programs of the group for that specific individual setpoint (MORN, DAY, EVE,
NIGHT) time and temperature to the startup default for that setpoint. Continued
pressing of the
or
buttons by the user will change setpoint time and temperature
settings as desired.
Entering Your Program
5.4.3
1. Place the system switch in the HEAT mode of operation. The display will show HEAT.
2. Press PROG button to enter Program setting
mode. MORN setpoint of the Whole Week Quick
Program Group will be displayed. The display will
show M, TU, W, TH, F, SA, SU to indicating the
whole week is being programmed. The hour
portion of the setpoint time and the AM/PM
indicator will be flashing.
3. If you desire to use a different Quick Program Group or Individual Day program mode you
can change by pressing the DAY/TIME button to select another group in the following
sequence, Whole Week - Weekday - Weekend - Monday - Tuesday - Wednesday -
Thursday - Friday - Saturday - Sunday - Whole Week.
4. Once you have finished your Quick Program Group or Individual Day selection. Press the
or
buttons to change the time to the desired hour in one hour increments, press PROG
button. The minute portion of the setpoint time will begin flashing.
5. Press the
or
buttons to change the time to the desired minute in 10-minute
increments, press PROG button. The SET TEMP will begin flashing.
6. Press the
or
buttons to change the setpoint temperature to the desired setting in 1˚ F
increments (0.5˚ C), press PROG button. The thermostat will now display the DAY setpoint
time and temperature. Again, you will see the hour portion of the setpoint time and the
AM/PM indicator will be flashing.
7. Follow steps 4 through 6 to set the setpoint times and temperatures for the DAY, EVE and
NIGHT setpoints for the Quick Program Group or Individual Day selection for the HEAT mode.
5
PROGRAMMING
CONTINUES ON PAGE
cont.
or
buttons. This will reset all the
9
8
5
PROGRAMMING
Setting Your Energy Saving Programs cont.
5.4
8. Place the system switch in the COOL mode of operation. The display will show COOL.
Follow steps 2 through 6 to program the setpoint times and temperatures for the Quick
Program Group or Individual Day selection for the COOL mode.
9. Repeat steps 3 through 8 for additional Quick Program Groups or Individual Day
programming as required.
NOTE:
To erase all entered programs, current time of day, day of week and other user
settings, gently press RESET button using a paper clip or a small pencil tip. This will return
all Thermostat settings to their default values.
ADDITIONAL
6
OPERATION FEATURES
Review Set Temperature
6.1
1. Press and hold
or
buttons. The current
setpoint temperature will be displayed in the place
of the current room temperature, and the indicator
SET TEMP will be displayed.
2. The display will return to normal operating mode
when the
or
buttons are released. Continuing
to hold the
or
buttons for 3 seconds or longer will allow the user to temporarily
override the current programmed setpoint (See Temporary Program Override).
Temporary Program Override
6.2
1. Press and hold
or
buttons for 3 seconds. The
entire display will flash once and the SET TEMP
indicator will be flashing. Release the
buttons and press the
or
buttons again as
desired to adjust the set temperature.
2. The display will return to normal operating mode
after 15 seconds or you can press RESUME button.
3. The program indicator (MORN, DAY, EVE OR NIGHT) will be flashing in the display
indicating that a Temporary Program Override is in effect. The Temporary Program
Override will reset when the next setpoint time occurs.
Permanent Hold (Vacation) Mode
6.3
1. Press the HOLD button to permanently bypass the
program schedule. The current setpoint
temperature will be held permanently and HOLD
and TEMP will show in the display.
2. Press the HOLD button again to return the
thermostat to normal program operation.
3. You can view or change your setpoint at any time using the
(see Review Set Temperature or Temporary Program Override).
cont.
or
or
buttons
9
- Quick Links:
- Programming
Hide quick links:
Advertisement
Table of Contents
