Summary of Contents for AMX Video Sync Sensor VSS2
Page 1
instruction manual VSS2 Video Sync Sensor C o n t r o l S y s t e m A c c e s s o r i e s...
Page 2
RMA number. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party.
Page 3
ANY REASON AND UPON WRITTEN NOTICE TO LICENSEE. In the event that AMX terminates this License, the Licensee shall return or destroy all originals and copies of the AMX Software to AMX and certify in writing that all originals and copies have been returned or destroyed.
Table of Contents Product Information ...1 Front Panel... 1 Rear Panel ... 1 Applications ... 2 Features ... 2 Specifications ... 3 Installing The VSS2 ...5 Connecting the Wiring ... 5 Video 1 and 2 connectors ... 5 Sense out connector ... 5 12 VDC power supply connector...
Page 6
Table of Contents VSS2 Video Sync Sensor...
You can use the VSS2 for systems that require true power status for a VCR, tuner, or satellite receiver. The VSS2 monitors the video output of each source and sends a logic signal to a AMX input port in the AXCESS Central Controller. You can also use the logic signal output to control AMX closure-driven peripherals such as a PC1 Power Controller.
Two RCA jacks for each channel to allow loop-through operation Two solid-state outputs that send a logic low signal when video sync is present Front-panel LEDs that display on/off status for each channel Compatible with all AMX solid-state and closure input ports Video Destination 1 12 VDC...
Specifications The table below lists the specifications for the VSS2 Video Synch Sensor. Specifications Power Supply Power Consumption Sensitivity Front Panel Rear Panel Enclosure Dimensions (HWD) Weight Included Accessories Optional Accessories VSS2 Video Sync Sensor 12 VDC at 20 mA 2.4 W maximum •...
Page 10
Product Information VSS2 Video Sync Sensor...
You can connect up to two video devices to the RCA plug-in connectors on the VSS2. Once attached, you can connect up to two external sensing devices, a television manager, or a AMX control system to the four-pin Sense out connector on the rear panel. The following describes how...
Sense out connector 12 VDC power supply connector FIG. 6 Television manager and power supply wiring diagram FIG. 7 shows a typical connection of a AMX control system and power supply. Sense out connector 12 VDC power supply connector FIG. 7 AMX AXCENT Control System and power supply wiring diagram 12 VDC power supply connector FIG.
Installing The VSS2 Rack-Mounting the VSS2 (optional) To rack-mount the VSS2 into the optional AC-RK Accessory Rack Kit: 1. Remove any connected power, AXlink, and RS-232 connectors from the rear panel. 2. Remove the two screws on the front panel of the VSS2. 3.
Page 14
Installing The VSS2 VSS2 Video Sync Sensor...
Page 15
Installing The VSS2 VSS2 Video Sync Sensor...
Page 16
ATLANTA • BOSTON • CHICAGO • CLEVELAND • DALLAS • DENVER • INDIANAPOLIS • LOS ANGELES • MINNEAPOLIS • PHILADELPHIA • PHOENIX • PORTLAND • SPOKANE • TAMPA 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com...
Need help?
Do you have a question about the Video Sync Sensor VSS2 and is the answer not in the manual?
Questions and answers