Table of content 1. How to Use the Mobeye 1.1 To get ready in three steps 1.2 Step 1: SIM Card 1.3 Step 2: Place the batteries 1.4 Step 3: Program the phone numbers 1.5 Switching the motion detector on/off 1.5.1 Switching on...
Page 3
• Do not use in an environment where any inflammable gases, vapours or dust are present or could be present. ® • Reparation of the device may only be carried out by people, trained for Mobeye repair. • In case the device must be repaired, only original replacement components may be ®...
Page 4
It is also possible to let the siren sound. After an alarm the Mobeye will be in standby status for about 5 minutes. Hereafter it is able to report new movements.
1. Place the SIM card in the Mobeye Make sure this SIM card is not secured by a PIN code. 2. Place the four batteries. ® 3. Enter at least one phone number in the Mobeye 1.2 STEP 1: SIM CARD ® To use the Mobeye a SIM card of any provider is needed.
1.5 SWITCHING THE MOTION DETECTOR ON/OFF 1.5.1 Switching on ® To activate the Mobeye motion detector with your personal user code. Enter your user code Press “OK” The light turns red shortly and an indication tone is started. This repetitive tone will last during the exit delay of 30 seconds.
“OK” twice. Warning ® In case of a weak signal, the Mobeye can still be used, but there is a risk that message cannot be sent or will be received with a delay. In case of no reach, it is advised to use a SIM card of a provider with a stronger network.
Mobeye is in active mode. 1.8.1.6 Siren After the entry delay, the siren can sound during two minutes. At the same time the SMS text messages and telephone calls will be done. At soon as the Mobeye is switched off, the siren will stop.
Page 9
It is possible to test the loud alarm. During the test the siren will be heard until it is cancelled by <OK> <OK>. This test is also possible in case the Mobeye i110 is programmed as a silent alarm. 1.8.1.7 Temperature alarm ®...
In about 30 seconds the telephone programmed at memory place 01 will receive the settings in an SMS text message. 1.8.2.1 Reset to factory settings After entering your personal code – menu – 99 –OK the Mobeye is back to factory settings. You personal code will be 1111 again.
It is possible to send an extra text in the SMS text messages, in order to recognize ® which Mobeye the message has sent. This text (max. 20 characters) can be ® programmed by sending an SMS to the Mobeye Please follow the instructions:...
Page 12
The Mobeye first prepares the programming mode. The light flashes red (interval ® ca. 1 sec). As soon as the light turns green, the Mobeye is able to receive SMS- messages. In order to program the extra message text, send an SMS in following structure: ...
Page 13
1.9.1.2 Special functions Via the keypad it is possible to activate some special functions. Enter your 4-digit personal code Press “menu” -> light turns green Enter the menu number belonging to the function Press “OK” Menunr Description Send an SMS containing the settings to the 1 telephone number...
You do not receive a SMS with Telephone number is not Re-program the the settings. correct. telephone number Change the menunr.06 to „01‟. For other questions, please refer to the site www.mobeye.eu...
Batteries: 4 x CR123 Lithium 3.0 V • Power: 50 μA, short peaks of max. 2 A Support ® For support on technical problems regarding Mobeye please contact info@mobeye.eu. CONRAD IM INTERNET http://www.conrad.de ® This manual is published by Mobeye All rights, the translation included are reserved.
Need help?
Do you have a question about the i110 and is the answer not in the manual?
Questions and answers