Advertisement
1 1 - - 4 4 I I G G N N I I T T I I O O N N U U N N L L O O C C K K O O N N / / O O F F F F : : When ON this feature will unlock the doors when the ignition is turned off.
1 1 - - 5 5 A A C C T T I I V V E E / / P P A A S S S S I I V V E E L L O O C C K K I I N N G G : : If passive arming is selected in Menu One, Feature 1-1, then the system can be
programmed to either lock the doors when passive arming occurs, or only lock the doors when the system is armed
with a transmitter. Active locking means the doors will not lock when the system passively arms. Passive locking
means that the doors will lock whenever the system passively arms the optional starter kill (if connected).
1 1 - - 6 6 P P A A N N I I C C W W I I T T H H I I G G N N I I T T I I O O N N O O N N / / O O F F F F : : This feature allows the user to panic the system sounding the siren while the
ignition is on.
1 1 - - 7 7 D D O O O O R R L L O O C C K K P P U U L L S S E E D D U U R R A A T T I I O O N N : : Some European vehicles, such as Mercedes-Benz and Audi, require longer lock
and unlock pulses to operate the vacuum pump. Programming the system to provide 3.5 second pulses will accom-
modate the door lock interface in these vehicles. The default setting is 0.8 second door lock pulses.
1 1 - - 8 8 D D O O U U B B L L E E P P U U L L S S E E U U N N L L O O C C K K O O F F F F / / O O N N : : Some vehicles require two pulses on a single wire to unlock the doors. When
the double pulse unlock feature is turned on, the BLUE H4/3 wire will supply two negative pulses instead of a
single pulse. At the same time, the GREEN H4/1 wire will supply two positive pulses instead of a single pulse.
This makes it possible to directly interface with double pulse vehicles without any extra parts.
1 1 - - 9 9 C C H H A A N N N N E E L L 2 2 O O U U T T P P U U T T : :
In the d d e e l l a a y y e e d d v v a a l l i i d d i i t t y y default setting the Channel 2 output will output a negative (-) signal after the
button is pressed for more than 1.5 seconds and will continue until the button is released.
The l l a a t t c c h h e e d d output selection will output a negative signal as soon as the
continue until the button is pressed again.
The l l a a t t c c h h e e d d / / r r e e s s e e t t w w i i t t h h i i g g n n i i t t i i o o n n output selection operates just like the latched output but will reset or stop
when the ignition is turned on.
The 3 3 0 0 - - s s e e c c o o n n d d t t i i m m e e d d output selection will latch the Channel 2 output on for 30 seconds when the remote
button is pressed or until the button is pressed again within the 30 seconds.
1 1 - - 1 1 0 0 F F A A C C T T O O R R Y Y A A L L A A R R M M D D I I S S A A R R M M ( ( F F A A D D ) ) W W I I T T H H C C H H A A N N N N E E L L T T W W O O O O N N / / O O F F F F : : Any time Channel 2 is activated from the
remote transmitter the factory disarm output will pulse to disarm the vehicle's factory anti-theft device. This
option can be programmed off if desired.
1 1 - - 1 1 1 1 S S E E C C U U R R I I T T Y Y F F E E A A T T U U R R E E S S O O N N / / O O F F F F : : When On the security features (starter kill and panic) will activate if the igni-
tion key is turned On while the doors are locked. When Off the security features (starter kill and panic) will not
activate if the ignition key is turned On while the doors are locked.
1 1 - - 1 1 2 2 C C O O D D E E - - H H O O P P P P I I N N G G O O N N / / O O F F F F : : The system features Code-Hopping as an option. To use Code-Hopping technology,
this feature must be programmed On.
1 1 - - 1 1 3 3 C C H H A A N N N N E E L L 4 4 : : This output can be programmed to produce a validity output that will stay active as long as the
transmitter button assigned to that channel is pressed, a latched output, a latched output reset with ignition,
or a 30-second timed output.
© 2004 Directed Electronics, Inc. Vista, CA
button is pressed and will
3 3 3 3
Advertisement
