Table of Contents
Advertisement
Sys tem Check list & Trou ble shoot ing (Con tin ued)
Step 2.
Test the Im mo bi li za tion cir cuit.
Arm the Polaris 4 (either from inside or outside the vehicle) and wait 10 seconds. Turn the
ignition to the "ON" position.
n Engine does not respond and alarm triggers. This is the correct response, proceed to
step 3.
n Engine starts or cranks. The starter immobilization cir cuit has been mis wired.
Care fully re test the ve hi cle wires as noted in the Starter or Ignition Immobilization Cir cuit
section on page 10.
n Engine still starts or cranks after retesting all the wiring as noted on page 10, check the
power and ground connections. Then make sure the fuses are in the fuseholders, verify
the control unit connectors are securely fastened, verify the ignition wires are connected
to the true ignition line instead of a 12V or accessory line, and verify that the
transmitters are programmed correctly.
Step 3.
Test the chirps.
Close all doors and arm the Po laris 4 by pressing the
n 2 Chirps: This is the correct response. Proceed to step 4.
n 1 Chirp: If you hear only one chirp, the Polaris 4 had previously armed itself passively
and by pressing the button, the system disarmed (remote disarming is acknowledged
with one chirp and one parking light flash). Disarm and rearm the system.
n 4 Chirps: If you hear 4 chirps ei ther im me di ate ly or 5-10 sec onds af ter the ini tial two
chirps, a trig ger or sen sor is open or active, or the ve hi cle has de layed cour tesy lights and
the De layed Cour tesy Lights fea ture has not been programmed on. Dis arm with the
re mote con trol, en ter the ve hi cle and turn on the ig ni tion. The LED will flash 1–10
times, pause, then re peat the same number of flashes (the flash cy cle re peats five times
for your con ven ience). Ref er to the following chart.
Num ber of LED flashes
be tween pauses
2 flashes
4 flashes*
5 flashes
6 flashes
7 flashes
10 flashes
*
If the de layed cour tesy lights fea ture is ac ti vated, this trig ger in di ca tion will not be pro vided.
§ If the door trig ger is in di cated, ac ti vate the de layed cour tesy lights fea ture.
n No chirps. If there are no chirps, ver ify that the Chirps fea ture (User-Programming -
col umn 2, row 1) is "On" and check the wir ing con nec tions as noted in the High Output
Si ren sec tion on page 11.
NOTE: If none of the troubleshooting techniques described in steps 3 - 7
corrects the problem, perform the following diagnostics:
n Make sure the fuses are in the fuse hold ers.
n Check the power and ground con nec tions.
n Ver ify that the con trol unit con nec tor is prop erly in serted into the con trol unit.
n Verify that the ig ni tion in put is con nected to the true ig ni tion line instead of a 12V line.
Find the true ig ni tion line by fol low ing the appropriate steps of the Starter or Ignition
Immobilization Cir cuit sec tion on page 10.
n Ver ify that the trans mit ters are pro grammed cor rectly.
button on the remote control.
Trig ger/sen sor in di ca tion
Dual-Zone Piezo Sensor or Optional Sensor
Door Trigger*
Trunk Trigger (trunk only, if IntelliStart 4 has been installed)
Hood Trigger (only if IntelliStart 4 has been installed)
An attempt was made to turn the ignition "ON" or start the
engine while the system was armed
Power Interruption
18
Advertisement
Table of Contents
