Fire Sense LIP-09A-TGG Instruction Manual

Outdoor patio heater

Hide thumbs Also See for LIP-09A-TGG:

Manual (15 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Fire Sense LIP-09A-TGG

Page 1 Outdoor Patio Heater Model # LIP-09A-TGG Item # 61166 ATTACH YOUR RECEIPT HERE Serial Number ___________ Purchase Date ______ Manufacturer: Changzhou Wellife Furnace Co., Ltd Questions, problems, missing parts? Before returning to your retailer, call our customer service hotline at 1-866-985-7877, 9 a.m.
Page 2: Table Of Contents
TABLE OF CONTENTS Table of Contents………………………………….....Page 2 Before You Begin............Page 2 Safety Information............Page 3-4 Package Contents………………………………….....Page 5 Hardware Contents............Page 6 Assembly.................Page 6-10 Operating Instructions……………........Page 11-13 Care and Maintenance……………………......Page 14 Troubleshooting……………………………………......Page 15 Replacement Parts List.............Page 16 Warranty Information……………........…Page 17 BEFORE YOU BEGIN Please read and understand this entire manual before attempting to assemble, operate or install this appliance.
Page 3: Safety Information
SAFETY INFORMATION...
Page 4 SAFETY INFORMATION...
Page 5: Package Contents
PACKAGE CONTENTS ASSEMBLY PART DESCRIPTION Reflector Emitter Upper Supports Lower Supports Mesh Guards Glass Tube Connector Glass Tube 2 pcs Burner Tank Housing/Base Assembly (with wheels) Regulator/Hose assembly Cylinder Holder...
Page 6: Hardware Contents
HARDWARE CONTENTS ASSEMBLY ASSEMBLY PREPARATION Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package contents list and hardware contents as listed on pages 2 and 3 of this manual. If any part is missing or damaged, do not attempt to assemble this product.
Page 7: Assembly
ASSEMBLY 1. Locate 4 pieces of Upper Supports and 4 pieces of Lower Supports. Slide 1 - Mesh Guard Connector over bottom end of Upper Support, then screw Upper Support onto Lower Support (Note: Mesh Guard Connector will remain loose and able to slide on the supports.) Repeat with remaining Upper and Lower Supports and Mesh Guard Connectors until you have 4 assembled Supports.
Page 8 ASSEMBLY . Fit the Emitter (B) down over the threaded end of the assembled Supports by lining up the holes in the corners of the Emitter with the Supports and sliding the Emitter down over the Supports. Secure the Emitter to the Supports using 4 pieces of B - M8 Spacer. Tighten with an open end wrench.
Page 9 ASSEMBLY 5. Attach Reflector (A) to top of Supports. Align holes in bottom of Reflector with Supports and slide Reflector down over Supports. 6. Secure Reflector to Supports with 4 pieces A - M8 Nut. Tighten with an open end wrench. Hardware Used: 4 x A, M8 Nut 7.
Page 10 ASSEMBLY 9. Attach Mesh Guards to Supports. Hint: It is best to begin with bottom pieces of Mesh Guards. Locate one Mesh Guard. Slide the Mesh Guard Connectors up the Support and hold them in the center of the Support. Then insert the longer tabs at the bottom of the Mesh Guard into the holes on Tank Housing/Base.
Page 11: Operating Instructions
OPERATING INSTRUCTIONS A minimum supply pressure of .5 psi is required for the purpose of input adjustment of propane gas. Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance. A cylinder must be stored outdoors in a well-ventilated area out of the reach of children. A disconnected cylinder must have dust caps tightly installed and must not be stored in a building, garage, or any other enclosed area.
Page 12: Before Turning Gas Supply On
OPERATING INSTRUCTIONS Caution: Do not attempt to operate this appliance until you have read and understand all Safety Information in this manual and all assembly is complete and leak checks have been performed. WARNING CONCERNING THE GLASS TUBE: ●NEVER use this heater when it is raining. The glass tube will break when it comes in contact with water. ●NEVER splash any liquid on the glass tube while the heater is in operation.
Page 13 OPERATING INSTRUCTIONS When Heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners.
Page 14: Care And Maintenance
CARE AND MAINTENANCE After Operation: 1. Gas control knob is in OFF position. 2. Gas tank valve is OFF. 3. Disconnect gas line. To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Keep exterior surfaces clean.
Page 15: Troubleshooting
TROUBLESHOOTING If you have any questions regarding this product, please call our customer service hotline at 1-866-985-7877, 9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Gas valve may be off Turn gas valve ON Fuel tank may be empty Refill LPG tank...
Page 16: Replacement Parts List
REPLACEMENT PARTS LIST ASSEMBLY For questions regarding this product or to purchase replacement parts, please call our customer service hotline at 1-866-985-7877, 9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net. PART DESCRIPTION Reflector Emitter Upper Supports Lower Supports Mesh Guards Glass Tube...
Page 17: Warranty Information
Customer Service Hours: Mon. – Fri. 9:00 a.m. – 6:00 p.m. (EST) Fire Sense®, Mojave Sun ®, and Well Traveled Living® are registered trademarks of Well Traveled Imports, Inc®. All assembly instruction presentations are the property of Well Traveled Imports, Inc.® and are protected by U.S. copyrights and trademarks.

Fire Sense LIP-09A-TGG Instruction Manual

Quick Links

Related Manuals for Fire Sense LIP-09A-TGG

Summary of Contents for Fire Sense LIP-09A-TGG

Table of Contents