Raypak 5350 Series Installation & Operating Instructions Manual
Heat pump pool & spa heater
Hide thumbs
Also See for 5350 Series:
- Installation & operating instructions manual (29 pages) ,
- Installation and operating instructions manual (60 pages)
Table of Contents
Advertisement
INSTALLATION & OPERATING
Heat Pump
Pool & Spa
Heater
Model Series
5350, 6350,
6350HC, 8350 &
8350HC
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and
liquids or other combustible materials in the vicinity of this or any other appliance. To
do so may result in an explosion or fire.
NOTE: The instructions in this manual are for the use of qualified individuals specially trained and experienced
in the installation and maintenance of this type of equipment and related system components. Installation and
service personnel are required by some states to be licensed. Persons not qualified shall not attempt to install,
service, or maintain this equipment.
This manual should be maintained in legible condition and kept adjacent to the heat pump pool heater or in a
safe place for future use.
Catalog No. RP6000.552E
INSTRUCTIONS
Effective: 06-28-13
Replaces: 11-23-10
P/N 241377 Rev. 7
92-103778-03-07
R
C
US
Advertisement
Table of Contents
Related Manuals for Raypak 5350 Series
Summary of Contents for Raypak 5350 Series
-
Page 1: Heat Pump
Heat Pump Pool & Spa Heater Model Series 5350, 6350, 6350HC, 8350 & 8350HC FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids or other combustible materials in the vicinity of this or any other appliance. To do so may result in an explosion or fire. - Page 2 Rev. 7 reflects the following: Changes to: Installation Considerations on pages 6-7, High Wind Installation diagram on page 8, Table C on page 16, Wiring diagrams on pages 21-24. Additions: Wiring diagram on page 25. Deletions: None.
-
Page 3: Water Chemistry
Water Chemistry (Corrosive water voids all warranties) For your health and the protection of your pool equipment, it is essential that your water be chemically balanced. The following levels must be used as a guide for balanced water. Recommended Level(s) Fiberglass Pools Fiberglass Spas Other Pool &... -
Page 4: Table Of Contents
ONTENTS Water Chemistry Troubleshooting Warnings Service Call Verification Pay Attention to These Terms Power Supply Water Flow Introduction Time Clock Adjustment Installation Considerations Electrical Connections Plumbing Diagrams Water Connections Wiring Diagram — 208V/230V Pressure Drop Single-Phase — Analog Models Controls & Indicator Lamps Wiring Diagram —... - Page 5 — Warnings Pay Attention to These Terms Indicates the presence of immediate hazards which will cause severe personal injury, death DANGER: or substantial property damage if ignored. Indicates the presence of hazards or unsafe practices which could cause severe personal WARNING: injury, death or substantial property damage if ignored.
-
Page 6: Introduction
Introduction Installation Considerations WARNING: Do not install the unit within 3 ft of WARNING: This pool/spa heat pump pool heater is fossil fuel burning heaters. Air intake along the an electromechanical machine that incorporates a sides of this heat pump pool heater could disturb pressurized refrigerant gas in a sealed system. -
Page 7: Electrical Connections
60” AIR FLOW OUT 3 FT 12” FLOW FLOW HEATER Fig. 1: Installation Clearances • Irrigation water should be directed away from the All wiring must be in accordance with the National heat pump pool heater-water spray can damage Electrical Code, NFPA No. 70, latest edition, and all the heat pump pool heater. -
Page 9: Water Connections
Minimum Circuit Maximum Breaker Model No. VAC in - Phase - Hz Ampacity (A) Size (A) 5350 208/230 - 1 - 60 40.0 6350/6350HC 208/230 - 1 - 60 42.0 208/230 - 1 - 60 42.0 8350/8350HC 208/230 - 3 - 60 34.0... - Page 10 Defrost Switch: Prevents heat pump pool heater WARNING: Install a check valve and/or a Hartford operation if ambient air temperature falls below a pre- loop AFTER the heat pump pool heater and determined safe minimum (approximately 42° F). BEFORE any chlorinating devices. Install any auto- matic chemical feeders AFTER the heat pump pool Delay Timer: Prevents compressor from short cycling, heater.
-
Page 11: System Start-Up
• Compressor Delay Active (amber lamp): Under 4. Allow the heat pump pool heater to operate for a normal operation, when lit, indicates compressor few minutes to stabilize operating pressures and to anti-short cycle timer is active. The fan will run but allow various component temperatures to normal- the compressor will be OFF for 6 to 8 minutes. -
Page 12: Instructions
Digital Controls Operating Heat/Cool Operation (Models Instructions 6350HC and 8350HC Only) The electronic board has the capability of memorizing The heat/cool model is designed to both heat and cool two different programmed temperature settings as fol- the pool. To select heat or cool mode, push the SET key until H/C is displayed. -
Page 13: Seasonal Start-Up Or Annual Check
System Start-Up Summer Shutdown If you do not plan to use the heat pump pool heater 1. Verify that the Digital Board is displaying a temper- during the summer months, secure and protect it as ature and the pool pump is running and water is follows: circulating properly. -
Page 14: Cabinet Care (Optional)
Maintenance Troubleshooting If your unit does not operate, or simply does not heat NOTE: The heat pump pool heater MANUFACTUR- your pool water, Fault Codes (digital models), or the ER IS NOT RESPONSIBLE for maintenance indicator lamps (analog models) on the front control adjustments. -
Page 15: Water Flow
• Is airflow through the unit being obstructed? Restrictions such as shrubbery, tall grass, dirty Service Call Verification coils, or any other obstruction to airflow will reduce performance. NOTE: The Raypak Service number is 800-260-2758. • pool blanket/cover being used? - Page 16 Fault Code Meaning of Code The desired programmed temperature point is lower than 60°F (15°C). Shortage of refrigerant gas in the unit or faulty low pressure control. The unit will show LP & LP3 (LP3) after 3 LP faults and shuts down the unit and pool pump for protection. If this occurs, you should call for service.
-
Page 17: Plumbing Diagrams
Plumbing Diagrams Fig. 6: For systems with pumps of less than 2 HP (under 80 gpm), no external bypass is required. Connections are 2-inch unions. Plumb the heat pump pool heater AFTER the filter and BEFORE any chlorinators. - Page 18 Fig. 7: For systems with pumps of 2 HP or greater (over 80 gpm), an external bypass is required. Adjust the bypass valve to divert a minimum of 40 gpm through the heat pump pool heater. Connections are 2-inch unions. Plumb the heat pump pool heater AFTER the filter and BEFORE any chlorinators.
- Page 19 Fig. 8: Pool Piping for Heat Pump Pool Heater and Gas Pool Heater...
- Page 20 Fig. 9: Pool Piping for Heat Pump Pool Heaters, Multiple, Primary/Secondary...
-
Page 21: Wiring Diagram — 208V/230V Single-Phase — Analog Models
Wiring Diagram — 208V/230V Single-Phase — Analog Models... -
Page 22: Wiring Diagram — 208V/230V Single-Phase — Digital Models
Wiring Diagram 208V/230V Single-Phase Digital Models... -
Page 23: Wiring Diagram — 208V/230V Three-Phase — Analog Models
Wiring Diagram 208V/230V Three-Phase Analog Models... -
Page 24: Wiring Diagram — 208V/230V Three-Phase — Digital Models
Wiring Diagram 208V/230V Three-Phase Digital Models... -
Page 25: Wiring Diagram — 460V Three-Phase — Analog Models
Wiring Diagram 460V Three-Phase Analog Models... -
Page 26: Installing A Remote Control Device
Installing a Remote Control Installing a Remote Control Device on Analog Heaters Device on Digital Heaters Wiring Wiring For a 2-wire control, use the TOTAL and COMMON For a 2-wire control, use the TOTAL and COMMON connections on the heat pump pool heater wiring connections on the heat pump pool heater wiring block. - Page 28 Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 Fax (805) 278-5468 Heat Pump Service 1-800-260-2758 Litho in U.S.A.