Table of Contents
Advertisement
Quick Links
This manual should be maintained in legible condition and kept adjacent
to the heat pump or in a safe place for future use.
For additional information call:
The instructions in this manual are for the use of qualified individuals specially
trained and experienced in the installation and maintenance of this type of
equipment and related system components. Installation and service personnel
are required by some states to be licensed.
Persons not qualified must not attempt to install, service, or maintain this
equipment.
Replaces: All Previous Versions
Raypak
Swimming Pool and
Spa Heat Pump
OWNER and
INSTALLATION MANUAL
Model RHP 33
The Pool and Spa Heating Experts
Effective Date: Dec 2004
RHP Series
®
(03) 9757 3333
R
C
US
9900276
Part No.
Advertisement
Table of Contents
Related Manuals for Raypak RHP 33
Summary of Contents for Raypak RHP 33
-
Page 1: Installation Manual
This manual should be maintained in legible condition and kept adjacent to the heat pump or in a safe place for future use. For additional information call: The instructions in this manual are for the use of qualified individuals specially trained and experienced in the installation and maintenance of this type of equipment and related system components. - Page 2 PRODUCT SAFETY SIGNS AND LABELS This manual, as well as the pool/spa heat pump itself, contains product safety signs and labels. Please read these signs and labels, as they convey important safety information about hazards that may be potentially present in and around the heat pump. They are classified according to relative seriousness of the hazard potential, from DANGER at the most serious, to WARNING, or CAUTION at the least serious.
-
Page 3: Table Of Contents
Control Panel Cover Assembly Replacement Parts List ......13 Heat Pump Assembly Replacement Parts List - RHP 33 ......14 Limited Warranty Information . -
Page 4: Introduction
As with all pool/spa heat pumps, compared to other types of pool heat pumps such as gas, this heat pump has lower heating capacity on a KW/hr basis. As a result, it will be required to operate longer to accomplish the desired results. It may, at certain times, operate as much as 24 hours per day. -
Page 5: Electrical Connections
The power supply connections to the unit are located behind the control panel. Remove the control panel to expose the electrical controls. Line voltage connections are made at the line voltage terminals of the compressor contactor. Refer to the Heat Pump Schematic (page 11) and the Control Panel Assembly Replacement Parts List (page 12). -
Page 6: Water Connections
The heat pump inlet and outlet connections are NOT interchangeable. They must be connected as instructed below. 1. Connect the heat pump in the return water line between the pool filter and the pool. See page 10, Plumbing Diagrams. 2. Connect the filter outlet to the fitting marked 3. -
Page 7: Initial Start-Up And Check
Indicator Lamps: There are 6 indicator lamps located on the unit control panel: • (amber lamp): When lit, indicates power is applied to the unit. Power • (green lamp): When lit, indicates normal water flow. Water Flow • (green lamp): When lit, indicates the actual water temperature is below the Heat Demand target water temperature. -
Page 8: Seasonal Start-Up Or Annual Check
6. Turn the control switch to either colder than the setting of the temperature control, the heat pump will start up and run. It will run until the desired water temperature is reached, or until the pool pump shuts OFF. -
Page 9: Summer Shutdown
VIII. Summer Shutdown If you do not plan to use the pool heat pump during the summer months, secure and protect it as follows: 1. From the control panel, turn the control switch to 2. Turn the heat pump power switch to OFF. -
Page 10: Troubleshooting
Use the pool chemistry test kit to confirm there is no chlorine in the condensate. Or, b. Shut the heat pump OFF and leave the filter pump running to see if the water disappears. If the water disappears, it would confirm the water to be condensate. - Page 11 operation. After the desired temperature is reached, return the system to normal operation. • Is airflow through the unit being obstructed? Restrictions such as shrubbery, tall grass, dirty coils, or any other obstruction to airflow will reduce performance. • Is the pool blanket/cover being used? Unblanketed pools can lose up to 6° per night compared to 2 degrees or less when a blanket is used.
- Page 12 POWER SUPPLY • Verify that all circuit breakers are reset and working properly. • If the lamp on the control panel still does not light, contact the installing dealer, Power since it may be a power problem requiring an electrician. WATER FLOW •...
-
Page 13: Plumbing Diagrams
For systems with pumps of 2 HP (1.5Kw) or greater (over 300 l/min), an external bypass is required. Adjust the bypass valve to divert a minimum of 150 l/min gpm through the heat pump. Connections are 50mm pipe slip. Plumb the heat pump after the filter and before any chlorinators. -
Page 14: Heat Pump Schematic
Heat Pump Schematic Pink Coil Coil... -
Page 15: Control Panel Assembly Replacement Parts List
Control Panel Assembly Replacement Parts List ITEM QTY DESCRIPTION Control Panel Contactor Compressor Fan Relay Control Board 24Volt Thermostat Transformer Timer IMC 203 Capacitor Pressure Switch Water Fuse Block Bushing Heyco 2184 Stand-off RLCBSR1 Terminal Strip Clamp Capacitor 04 Ground Lug Fuse 2A Type 3AG PART No. -
Page 16: Control Panel Cover Assembly Replacement Parts List
Control Panel Cover Assembly Replacement Parts List ITEM QTY DESCRIPTION Control Panel Cover Switch Type A403 Knob Label Control Panel Lamp Green Lamp Red Lamp Amber Front Back PART No. RHP Control Panel Cover... -
Page 17: Heat Pump Assembly Replacement Parts List - Rhp 33
Heat Pump Assembly Replacement Parts List - RHP 33 ITEM QTY Assembly Base Evaporator Coil Access Panel Power Input Panel Cover, Top Compressor, Scroll Corner Support Heat Exchanger Retainer, Screen Control Panel Cover Fan Guard Fan Blade Fan Motor Water Manifold Assembly...