Related Manuals for AirStage UTY-LNH series
Summary of Contents for AirStage UTY-LNH series
-
Page 1: Wireless Remote Controller
OPERATING MANUAL PERATING ANUAL AIR CONDITIONER WIRELESS REMOTE CONTROLLER Remote Controller UTY-LNH KEEP THIS MANUAL FOR FUTURE REFERENCE P/N9379143004-06 FUJITSU GENERAL LIMITED... -
Page 2: Table Of Contents
CONTENTS ECONOMY OPERATION ..........9 SAFETY PRECAUTIONS ..........1 FILTER RESET ............... 9 FEATURES AND FUNCTIONS ........2 SELECTING THE REMOTE CONTROL UNIT NAME OF PARTS ............3 SIGNAL CODE .............. 10 PREPARATION ............... 4 OPERATING TIPS ............11 TIMER OPERATION ............7 TROUBLESHOOTING .......... -
Page 3: Features And Functions
FEATURES AND FUNCTIONS AUTOMATIC OPERATION WIRELESS REMOTE CONTROL UNIT The WIRELESS REMOTE CONTROL UNIT allows convenient ● COOLING MODEL control of air conditioner operation. Merely press the “START/STOP” button, and the unit will begin automatic operation in the Cooling or Dry mode as appropriate, in accordance with the temperature setting and the actual temperature of the room. -
Page 4: Name Of Parts
NAME OF PARTS Remote control unit Display panel Display To facilitate explanation, the accompanying illustration has been drawn to show all possible indicators; in actual opera- tion, however, the display will only show those indicators appropriate to the current operation. F Signal Transmitter 1 “MODE”... -
Page 5: Preparation
PREPARATION Load Batteries (AAA/LR03/R03 x 2) WARNING Never allow the alkaline batteries to short- circuit. Never disassemble, heat or place Press and slide the battery compartment lid on the them in fi re. reverse side to open it. Doing so can cause the strong alkaline ●... - Page 6 OPERATION To Select Mode Operation Press the “START/STOP” button. The receiver unit control panel’s OPERATION Indicator Lamp (green) will light. The air conditioner will start operating. Press the “MODE” button to select the desired mode. Each time the button is pressed, the mode will change in the following order. AUTO COOL HEAT...
- Page 7 To Stop Operation Press the “START/STOP” button. The OPERATION Indicator Lamp (green) will go out. About AUTO CHANGEOVER Operation AUTO: ● When AUTO CHANGEOVER operation fi rst selected, the fan will ope-rate at very low speed for about 1 minute, during which time the unit detects the room conditions and selects the proper operating mode.
-
Page 8: Timer Operation
TIMER OPERATION Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (☞ P. 4). To Use the ON timer or OFF timer Press the “START/STOP” button To Cancel the Timer Use the “TIMER MODE”... -
Page 9: Sleep Timer Operation
SLEEP TIMER OPERATION Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped. To Use the SLEEP Timer To Cancel the Timer: While the air conditioner is operating or stopped, press the Use the “TIMER MODE”... -
Page 10: Economy Operation
ECONOMY OPERATION Begin Air Conditioner operation before performing this procedure. To Use the ECONOMY Operation Press the “ECONOMY” button. “ECO” appears on the Remote Control Unit display. Economy operation begins. To Stop the ECONOMY Operation Press the “ECONOMY” button again. “ECO”... -
Page 11: Selecting The Remote Control Unit Signal Code
SELECTING THE REMOTE CONTROL UNIT SIGNAL CODE When 2 or more air conditioners are installed in a room and the remote control unit is operating an air conditioner other than the one you wish to set, change the signal code of the remote control unit to operate only the air conditioner you wish to set (4 selections pos- sible). -
Page 12: Operating Tips
OPERATING TIPS ● Remote control unit may not be available depending on the functions, while local operation with a standard remote control unit, including a wireless remote control unit, is prohibited. ● Display of operating condition on the indoor unit and this unit may differ while indoor unit is operated with the RC Prohibition control. - Page 13 About Mode Operation *Heating: ● Use to warm your room. During Heating mode: ● When Heating mode is selected, the air conditioner will operate at very low Set the temperature to a temperature setting fan speed for about 3 to 5 minutes, after which it will switch to the selected that is higher than the current room tempera- fan setting.
-
Page 14: Troubleshooting
TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “HEAT PUMP MODEL”. In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the power supply plug or turn off the circuit breaker, and consult authorized service personnel. Merely turning off the unit’s power switch will not completely disconnect the unit from the power source. -
Page 15: Specifications
Instructions relating to heating (*) are applicable only to “HEAT PUMP MODEL”. Symptom Items to check See Page CHECK ONCE Doesn’t operate at all: ● Has the circuit breaker been turned off? — MORE ● Has there been a power failure? ●...