Related Manuals for Wyrestorm MX-0808-HDBT
Summary of Contents for Wyrestorm MX-0808-HDBT
- Page 1 8 x 8 Output Full HD Matrix Switch Part Number MX-0808-HDBT Instruction Manual Thank you for choosing this WyreStorm product. Please read these instructions carefully before installing to avoid complications later.
-
Page 2: Table Of Contents
Contents Introduction Introduction The MX-0808-HDBT is a 8x8 matrix switcher that allows any of its 8 HDMI inputs to be routed over distance to Features any combination of the 8 display outputs via UTP cable, regardless of HDCP source encryption. -
Page 3: Features
• Allows up to 8 HDMI audio/video devices to be independently switched through up to 8 HDMI displays or projectors NOTE: WyreStorm reserves the right to make changes to hardware, packaging and any accompanying documentation • Each output requires a UTP receiver behind each display used: without prior written notice. -
Page 4: Package Contents
• 8 x IR TX Emitters (small sensor for Input source) RS485 port - alternative control of the matrix via RS485 cable • 1 x MX-0808-HDBT remote control (incl. battery) LAN port - for controlling the Matrix remotely over an IP... - Page 5 Front Panel Rear Panel 06 07 08 09 HDBaseT Single In-wall HDBaseT Single Cat5e/6/7 Display Receiver Cat5e/6/7 Display Receiver Part Number RX-100IR-HDBT Part Number RX-100IR-HDBT-IW Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343...
-
Page 6: Typical Application
Connect your HDMI input sources (such as: HD-DVD, PS3/, XBOX360, satellite/cable, Blu-Ray etc.) to HDMI Connect the HDMI OUT of the DISPLAY RECEIVER to the inputs 1 – 8 of the MX-0808-HDBT MATRIX. HDMI IN of the display. ATTENTION Do Not Hotplug! - Please insert and Plug the 3.5mm jack of the IR RX receiver into the IR RX... -
Page 7: Basic Operation
Attention – if you make a mistake, press “C” (Clear) to clear the previous number and go back a step. M1 M2 M3 preview observ Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343 save... -
Page 8: Basic Remote Control
1manually. See below. Matrix System Code Switch 0x12 0x08 In the event that two MX-0808-HDBT units are used side by side 0x55 0x4a in the rack, the matrix is capable of switching between two distinct IR System Codes to allow control of either matrix individually via the handset. -
Page 9: Advanced Operation
‘noise’ or interference. The exclusion of Deep Colour from the EDID reduces bandwidth to allow the signal to pass through the switch easier. Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343... - Page 10 Support 1080P7.1 Audio Video: 1080i Video: 1080P Video: 1080P Audio: stereo Audio: 7.1 Audio: stereo Fix EDID DIP: 001 DIP: 001 1080i-2CH Copy AVR’s Copy Tv1’s EDID EDID Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343...
- Page 11 Straight cable runs using solid core UTP are recommended. If cable runs are reaching the upper limit of receiver capabilities, boost the signal by using a WyreStorm HDBT extender set of transmitter and receiver. HDBaseT Extender Set...
- Page 12 16db/-6db 26db/-6db If repeated attempts to calibrate the screen continue to generate M1 M2 M3 16db/-9db 26db/-9db FAILURE messages, contact your authorised WyreStorm dealer for assistance. 19db/0db 27db/0db save 19db/-3db 26db/-3db...
- Page 13 Controlling the MX-0808-HDBT using COM CTL PC software You can also control the matrix via PC using the COM CTL software provided on the disk included with your unit. In addition to the controls found on touch panel display of the matrix itself, COM CTL also offers further information on the status of the system and greater control of settings, including full configuration of the system for optimum performance.
- Page 14 NOT take effect in the matrix itself. This feature of the software is for dual cable PRO matrix models only. HDBT uses single cable transmission. Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343...
- Page 15 Note: your matrix IP address can also be obtained through the Ground Stop bits touch screen by following: Flow control None Male connector - 9 holes Main menu Info navigate to the IP column. Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343...
- Page 16 IR code Set MX-0808-HDBT Control Code The MX-0808-HDBT supports third party control systems and Output 1 < “08” “09”> learning handsets. Pressing the IR SET button in the COM 1 “00” 2 “01” 3 “02” 4 “03” 5 “04” 6 “05”...
- Page 17 Alternatively, you can open EDID from here if you have previously saved output EDID in bin format. Recommended if you frequently need to use specific output EDID, from a particular display, for example Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343...
-
Page 18: Troubleshooting
Note: If you are approaching the limits of the transmission 0808-HDBT, we are confident solutions can be found by capabilities, you will need to use a Wyrestorm HDBT working through the following troubleshooting checklist Extender set in your set up for the signal to transmit before seeking alternative technical support. - Page 19 Are you using WyreStorm emitters and receivers? The use correctly assigned within the system set up. of third party products/magic eyes may not be compatible.
-
Page 20: Faqs
HD content. Unlike competing products, have multiple identical sources yet the IR would be routed WyreStorm matrix switches are legal and comply with HDCP only to the applicable source. regulations. They do this by assigning a “key” to every display connected to the switch. -
Page 21: Maintenance
(HDMI Control Protocol) to the outgoing signal, this can sometimes have an effect on the HDMI signal. Limited warranty period: All WyreStorm products are covered by a 2 year PARTS and LABOUR warranty. During this period there will be no charge for 16. Maintenance unit repair, replacement of unit components or replacement of product if necessary. -
Page 22: Reference Logs
21. Reference Logs WyreStorm 08x08 HDBT Matrix INPUT installation reference log INPUT Input Source Location Source Details Source resolution & audio Cable number on settings Number Matrix Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343... - Page 23 WyreStorm 08x08 HDBT Matrix OUPUT installation reference log OUTPUT Output Output Location Display Details Display Resolution & Audio Cable number on Settings Number Matrix Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343...
- Page 24 Tel: + 901 384 3575 Fax: + 901 384 3574 Unit 22, Ergo Business Park, Swindon, Wiltshire, SN3 3JW UK Tel: +44 (0) 1793 230 343 Fax: +44 (0) 1793 230 583 WyreStorm Technical Support US: +86 6677 0053 UK:- +44 (0) 1793 238 338 Email: support@wyrestorm.com...
Need help?
Do you have a question about the MX-0808-HDBT and is the answer not in the manual?
Questions and answers